File content as of revision 0:7077d8f28b3e:

/*
 * Licensed under the GNU General Public License version 2 with exceptions. See
 * LICENSE file in the project root for full license information
 */

/** \file
 * \brief
 * EtherCAT RAW socket driver.
 *
 * Low level interface functions to send and receive EtherCAT packets.
 * EtherCAT has the property that packets are only send by the master,
 * and the send packets always return in the receive buffer.
 * There can be multiple packets "on the wire" before they return.
 * To combine the received packets with the original send packets a buffer
 * system is installed. The identifier is put in the index item of the
 * EtherCAT header. The index is stored and compared when a frame is received.
 * If there is a match the packet can be combined with the transmit packet
 * and returned to the higher level function.
 *
 * The socket layer can exhibit a reversal in the packet order (rare).
 * If the Tx order is A-B-C the return order could be A-C-B. The indexed buffer
 * will reorder the packets automatically.
 *
 * The "redundant" option will configure two sockets and two NIC interfaces.
 * Slaves are connected to both interfaces, one on the IN port and one on the
 * OUT port. Packets are send via both interfaces. Any one of the connections
 * (also an interconnect) can be removed and the slaves are still serviced with
 * packets. The software layer will detect the possible failure modes and
 * compensate. If needed the packets from interface A are resent through interface B.
 * This layer is fully transparent for the higher layers.
 */


#include "mbed.h"

#include <stdio.h>
#include <string.h>

#include "osal.h"
#include "oshw.h"

#ifndef MAX
#define MAX(a,b) (((a) > (b)) ? (a) : (b))
#define MIN(a,b) (((a) < (b)) ? (a) : (b))
#endif



/** Redundancy modes */
enum
{
   /** No redundancy, single NIC mode */
   ECT_RED_NONE,
   /** Double redundant NIC connection */
   ECT_RED_DOUBLE
};

/** Primary source MAC address used for EtherCAT.
 * This address is not the MAC address used from the NIC.
 * EtherCAT does not care about MAC addressing, but it is used here to
 * differentiate the route the packet traverses through the EtherCAT
 * segment. This is needed to find out the packet flow in redundant
 * configurations. */
const uint16 priMAC[3] = { 0x0101, 0x0101, 0x0101 };
/** Secondary source MAC address used for EtherCAT. */
const uint16 secMAC[3] = { 0x0404, 0x0404, 0x0404 };

/** second MAC word is used for identification */
#define RX_PRIM priMAC[1]
/** second MAC word is used for identification */
#define RX_SEC secMAC[1]




//******************************************************************************
// driver used:
// \mbed-os-5.5.7\targets\TARGET_STM\TARGET_STM32F7\device\stm32f7xx_hal_eth.c
//******************************************************************************


GPIO_InitTypeDef GPIO_InitStructure;



ETH_HandleTypeDef  hEth;           // ethernet interface handle structure

ETH_DMADescTypeDef DMATxDescTab[ETH_TXBUFNB];        // dma tx descriptors 
ETH_DMADescTypeDef DMARxDescTab[ETH_RXBUFNB];        // dma rx descriptors

uint8_t DmaTxBuff[ETH_TXBUFNB][ETH_MAX_PACKET_SIZE]; // dma tx buffers    
uint8_t DmaRxBuff[ETH_RXBUFNB][ETH_MAX_PACKET_SIZE]; // dma rx buffers      



HAL_StatusTypeDef HalStatus;       // response from Hal functions


//------------------------------------------------------------------------------

void EthInit()
{
                                        // HAL status codes
                                        //    
                                        // HAL_OK       = 0x00U,
                                        // HAL_ERROR    = 0x01U,
                                        // HAL_BUSY     = 0x02U,
                                        // HAL_TIMEOUT  = 0x03U
    
           
    uint8_t MACAddr[6] = {0x12, 0x34, 0x56, 0x78, 0x9A, 0xBC};  // mac address    

    hEth.State = HAL_ETH_STATE_RESET;   // don't know if it is useful !!!  
    
    hEth.Instance = ETH;                               
    hEth.Init.AutoNegotiation = ETH_AUTONEGOTIATION_DISABLE;
    hEth.Init.Speed = ETH_SPEED_100M;
    hEth.Init.DuplexMode = ETH_MODE_FULLDUPLEX;
    hEth.Init.PhyAddress = 0x00;
    hEth.Init.MACAddr = &MACAddr[0];    
    hEth.Init.RxMode = ETH_RXPOLLING_MODE;
    hEth.Init.ChecksumMode = ETH_CHECKSUM_BY_HARDWARE;
    hEth.Init.MediaInterface = ETH_MEDIA_INTERFACE_RMII;
        
    HalStatus = HAL_ETH_Init(&hEth);
    NVIC_DisableIRQ(ETH_IRQn);         // we don't use interrupt
    if (HalStatus != HAL_OK)
    {
        printf ("HAL_ETH_Init err %d\n", HalStatus);    
    }      
     
    HalStatus = HAL_ETH_DMATxDescListInit(&hEth, &DMATxDescTab[0], &DmaTxBuff[0][0], ETH_TXBUFNB);
    if (HalStatus != HAL_OK)
    {
       printf ("HAL_ETH_DMATxDescListInit err %d\n", HalStatus);   
    }    
                                                   
    HalStatus = HAL_ETH_DMARxDescListInit(&hEth, &DMARxDescTab[0], &DmaRxBuff[0][0], ETH_RXBUFNB);
    if (HalStatus != HAL_OK)
    {    
        printf ("HAL_ETH_DMARxDescListInit err %d\n", HalStatus);     
    }
    
    HalStatus = HAL_ETH_Start(&hEth);
    if (HalStatus != HAL_OK)    
    {
        printf ("HAL_ETH_Start err %d\n", HalStatus);  
    }   
}   

//------------------------------------------------------------------------------

int EthWrPacket (uint8_t* pBuff, uint16_t Len)
{
    uint8_t* pDmaBuff;          
            
    if ((hEth.TxDesc->Status & ETH_DMATXDESC_OWN) == (uint32_t)RESET) 
    
    {
        pDmaBuff = (uint8_t*)(hEth.TxDesc->Buffer1Addr);
        
        memcpy (pDmaBuff, pBuff, Len);    
   
        HalStatus = HAL_ETH_TransmitFrame(&hEth, Len);
        if (HalStatus != HAL_OK)
        {
            printf ("HAL_ETH_TransmitFrame err %d\n", HalStatus);       
            return NULL;
        }        
          
        return Len;
    }        
    
    else
    {
        return NULL;
    }
}    

//------------------------------------------------------------------------------

int EthRdPacket(uint8_t* pBuff)
{
    int Len;
    uint8_t* pDmaBuff;
    
    HalStatus = HAL_ETH_GetReceivedFrame(&hEth);            // check if a packet has been received
    
    if (HalStatus == HAL_OK)                                // packet received
    {
        Len = hEth.RxFrameInfos.length;                     // packet lenght        
        pDmaBuff = (uint8_t*)hEth.RxFrameInfos.buffer;      // DMA buffer pointer
               
        memcpy (pBuff, pDmaBuff, Len);                      // read the data 
    
                                                            // release the descriptor                                                           
        hEth.RxFrameInfos.FSRxDesc->Status |= ETH_DMARXDESC_OWN;
        hEth.RxFrameInfos.SegCount = 0;                     // reset segment count
                 
        return Len;                                         // return the number of bytes read
    }   
     
    else
    {   
        return NULL;                                        // no packet received
    }
}   

//*****************************************************************************
//              
//*****************************************************************************



static void ecx_clear_rxbufstat(int *rxbufstat)
{
   int i;
   for(i = 0; i < EC_MAXBUF; i++)
   {
      rxbufstat[i] = EC_BUF_EMPTY;
   }
}

/** Basic setup to connect NIC to socket.
 * @param[in] port        = port context struct
 * @param[in] ifname      = Name of NIC device, f.e. "eth0"
 * @param[in] secondary   = if >0 then use secondary stack instead of primary
 * @return >0 if succeeded
 */
int ecx_setupnic(ecx_portt *port, const char *ifname, int secondary)
{
   int i;
   int rVal;
   int *psock;

    EthInit();     
        
   if (rVal != 0)
      return 0;

   if (secondary)
   {
      /* secondary port struct available? */
      if (port->redport)
      {
         /* when using secondary socket it is automatically a redundant setup */
         psock = &(port->redport->sockhandle);
         *psock = -1;
         port->redstate                   = ECT_RED_DOUBLE;
         port->redport->stack.sock        = &(port->redport->sockhandle);
         port->redport->stack.txbuf       = &(port->txbuf);
         port->redport->stack.txbuflength = &(port->txbuflength);
         port->redport->stack.tempbuf     = &(port->redport->tempinbuf);
         port->redport->stack.rxbuf       = &(port->redport->rxbuf);
         port->redport->stack.rxbufstat   = &(port->redport->rxbufstat);
         port->redport->stack.rxsa        = &(port->redport->rxsa);
         ecx_clear_rxbufstat(&(port->redport->rxbufstat[0]));
      }
      else
      {
         /* fail */
         return 0;
      }
   }
   else
   {
      port->sockhandle        = -1;
      port->lastidx           = 0;
      port->redstate          = ECT_RED_NONE;
      port->stack.sock        = &(port->sockhandle);
      port->stack.txbuf       = &(port->txbuf);
      port->stack.txbuflength = &(port->txbuflength);
      port->stack.tempbuf     = &(port->tempinbuf);
      port->stack.rxbuf       = &(port->rxbuf);
      port->stack.rxbufstat   = &(port->rxbufstat);
      port->stack.rxsa        = &(port->rxsa);
      ecx_clear_rxbufstat(&(port->rxbufstat[0]));
      psock = &(port->sockhandle);
   }

   /* setup ethernet headers in tx buffers so we don't have to repeat it */
   for (i = 0; i < EC_MAXBUF; i++)
   {
      ec_setupheader(&(port->txbuf[i]));
      port->rxbufstat[i] = EC_BUF_EMPTY;
   }
   ec_setupheader(&(port->txbuf2));

   return 1;
}

/** Close sockets used
 * @param[in] port        = port context struct
 * @return 0
 */
int ecx_closenic(ecx_portt *port)
{
   if (port->sockhandle >= 0)
   {
      close(port->sockhandle);
   }
   if ((port->redport) && (port->redport->sockhandle >= 0))
   {
      close(port->redport->sockhandle);
   }
   return 0;
}

/** Fill buffer with ethernet header structure.
 * Destination MAC is always broadcast.
 * Ethertype is always ETH_P_ECAT.
 * @param[out] p = buffer
 */
 
void ec_setupheader(void *p)  
{   
   ec_etherheadert *bp;                   
     
   bp = (ec_etherheadert*)p;
 
 
   bp->da0 = oshw_htons(0xffff);
   bp->da1 = oshw_htons(0xffff);
   bp->da2 = oshw_htons(0xffff);
   bp->sa0 = oshw_htons(priMAC[0]);
   bp->sa1 = oshw_htons(priMAC[1]);
   bp->sa2 = oshw_htons(priMAC[2]);
   bp->etype = oshw_htons(ETH_P_ECAT);   
}

/** Get new frame identifier index and allocate corresponding rx buffer.
 * @param[in] port        = port context struct
 * @return new index.
 */
int ecx_getindex(ecx_portt *port)
{
   int idx;
   int cnt;

 //  mtx_lock (port->getindex_mutex);               //******//

   idx = port->lastidx + 1;
   /* index can't be larger than buffer array */
   if (idx >= EC_MAXBUF)
   {
      idx = 0;
   }
   cnt = 0;
   /* try to find unused index */
   while ((port->rxbufstat[idx] != EC_BUF_EMPTY) && (cnt < EC_MAXBUF))
   {
      idx++;
      cnt++;
      if (idx >= EC_MAXBUF)
      {
         idx = 0;
      }
   }
   port->rxbufstat[idx] = EC_BUF_ALLOC;
   if (port->redstate != ECT_RED_NONE)
   {
      port->redport->rxbufstat[idx] = EC_BUF_ALLOC;
   }
   port->lastidx = idx;

 //  mtx_unlock (port->getindex_mutex);             //******//

   return idx;
}

/** Set rx buffer status.
 * @param[in] port     = port context struct
 * @param[in] idx      = index in buffer array
 * @param[in] bufstat  = status to set
 */
void ecx_setbufstat(ecx_portt *port, int idx, int bufstat)
{
   port->rxbufstat[idx] = bufstat;
   if (port->redstate != ECT_RED_NONE)
   {
      port->redport->rxbufstat[idx] = bufstat;
   }
}

/** Transmit buffer over socket (non blocking).
 * @param[in] port        = port context struct
 * @param[in] idx         = index in tx buffer array
 * @param[in] stacknumber  = 0=Primary 1=Secondary stack
 * @return socket send result
 */
int ecx_outframe(ecx_portt *port, int idx, int stacknumber)
{
   int lp, rval;
   ec_stackT *stack;

   if (!stacknumber)
   {
      stack = &(port->stack);
   }
   else
   {
      stack = &(port->redport->stack);
   }
   lp = (*stack->txbuflength)[idx];
   (*stack->rxbufstat)[idx] = EC_BUF_TX;
 
   rval = EthWrPacket ((*stack->txbuf)[idx], lp); 
 
   return rval;
}

/** Transmit buffer over socket (non blocking).
 * @param[in] port        = port context struct
 * @param[in] idx = index in tx buffer array
 * @return socket send result
 */
int ecx_outframe_red(ecx_portt *port, int idx)
{
   ec_comt *datagramP;
   ec_etherheadert *ehp;
   int rval;

   ehp = (ec_etherheadert *)&(port->txbuf[idx]);
   /* rewrite MAC source address 1 to primary */
   ehp->sa1 = oshw_htons(priMAC[1]);
   /* transmit over primary socket*/
   rval = ecx_outframe(port, idx, 0);
   if (port->redstate != ECT_RED_NONE)
   {
 //     mtx_lock (port->tx_mutex);                              //******//
      ehp = (ec_etherheadert *)&(port->txbuf2);
      /* use dummy frame for secondary socket transmit (BRD) */
      datagramP = (ec_comt*)&(port->txbuf2[ETH_HEADERSIZE]);
      /* write index to frame */
      datagramP->index = idx;
      /* rewrite MAC source address 1 to secondary */
      ehp->sa1 = oshw_htons(secMAC[1]);
      /* transmit over secondary socket */
      //send(sockhandle2, &ec_txbuf2, ec_txbuflength2 , 0);
      // OBS! redundant not ACTIVE for BFIN, just added to compile
 
      port->redport->rxbufstat[idx] = EC_BUF_TX;
      
      EthWrPacket((uint8_t*)&(port->txbuf2), port->txbuflength2);
        
 //     mtx_unlock (port->tx_mutex);                                  //******//      
   }                                                                    

   return rval;
}

/** Non blocking read of socket. Put frame in temporary buffer.
 * @param[in] port        = port context struct
 * @param[in] stacknumber = 0=primary 1=secondary stack
 * @return >0 if frame is available and read
 */
static int ecx_recvpkt(ecx_portt *port, int stacknumber)
{
   int lp, bytesrx;
   ec_stackT *stack;

   if (!stacknumber)
   {
      stack = &(port->stack);
   }
   else
   {
      stack = &(port->redport->stack);
   }
   lp = sizeof(port->tempinbuf);
 
   bytesrx = EthRdPacket(*stack->tempbuf);
  
  
   port->tempinbufs = bytesrx;

   return (bytesrx > 0);
}

/** Non blocking receive frame function. Uses RX buffer and index to combine
 * read frame with transmitted frame. To compensate for received frames that
 * are out-of-order all frames are stored in their respective indexed buffer.
 * If a frame was placed in the buffer previously, the function retrieves it
 * from that buffer index without calling ec_recvpkt. If the requested index
 * is not already in the buffer it calls ec_recvpkt to fetch it. There are
 * three options now, 1 no frame read, so exit. 2 frame read but other
 * than requested index, store in buffer and exit. 3 frame read with matching
 * index, store in buffer, set completed flag in buffer status and exit.
 *
 * @param[in] port        = port context struct
 * @param[in] idx         = requested index of frame
 * @param[in] stacknumber = 0=primary 1=secondary stack
 * @return Workcounter if a frame is found with corresponding index, otherwise
 * EC_NOFRAME or EC_OTHERFRAME.
 */
int ecx_inframe(ecx_portt *port, int idx, int stacknumber)
{
   uint16  l;
   int     rval;
   uint8   idxf;
   ec_etherheadert *ehp;
   ec_comt *ecp;
   ec_stackT *stack;
   ec_bufT *rxbuf;

   if (!stacknumber)
   {
      stack = &(port->stack);
   }
   else
   {
      stack = &(port->redport->stack);
   }
   rval = EC_NOFRAME;
   rxbuf = &(*stack->rxbuf)[idx];
   /* check if requested index is already in buffer ? */
   if ((idx < EC_MAXBUF) && (   (*stack->rxbufstat)[idx] == EC_BUF_RCVD))
   {
      l = (*rxbuf)[0] + ((uint16)((*rxbuf)[1] & 0x0f) << 8);
      /* return WKC */
      rval = ((*rxbuf)[l] + ((uint16)(*rxbuf)[l + 1] << 8));
      /* mark as completed */
      (*stack->rxbufstat)[idx] = EC_BUF_COMPLETE;
   }
   else
   {
   //   mtx_lock (port->rx_mutex);                                  //******//
      /* non blocking call to retrieve frame from socket */
      if (ecx_recvpkt(port, stacknumber))
      {
         rval = EC_OTHERFRAME;
         ehp =(ec_etherheadert*)(stack->tempbuf);
         /* check if it is an EtherCAT frame */
         if (ehp->etype == oshw_htons(ETH_P_ECAT))
         {
            ecp =(ec_comt*)(&(*stack->tempbuf)[ETH_HEADERSIZE]);
            l = etohs(ecp->elength) & 0x0fff;
            idxf = ecp->index;
            /* found index equals requested index ? */
            if (idxf == idx)
            {
               /* yes, put it in the buffer array (strip ethernet header) */
               memcpy(rxbuf, &(*stack->tempbuf)[ETH_HEADERSIZE], (*stack->txbuflength)[idx] - ETH_HEADERSIZE);
               /* return WKC */
               rval = ((*rxbuf)[l] + ((uint16)((*rxbuf)[l + 1]) << 8));
               /* mark as completed */
               (*stack->rxbufstat)[idx] = EC_BUF_COMPLETE;
               /* store MAC source word 1 for redundant routing info */
               (*stack->rxsa)[idx] = oshw_ntohs(ehp->sa1);
            }
            else
            {
               /* check if index exist and someone is waiting for it */
               if (idxf < EC_MAXBUF && (*stack->rxbufstat)[idxf] == EC_BUF_TX)
               {
                  rxbuf = &(*stack->rxbuf)[idxf];
                  /* put it in the buffer array (strip ethernet header) */
                  memcpy(rxbuf, &(*stack->tempbuf)[ETH_HEADERSIZE], (*stack->txbuflength)[idxf] - ETH_HEADERSIZE);
                  /* mark as received */
                  (*stack->rxbufstat)[idxf] = EC_BUF_RCVD;
                  (*stack->rxsa)[idxf] = oshw_ntohs(ehp->sa1);
               }
               else
               {
                  /* strange things happened */
               }
            }
         }
      }
   //   mtx_unlock (port->rx_mutex);            //******//

   }

   /* WKC if matching frame found */
   return rval;
}


/** Blocking redundant receive frame function. If redundant mode is not active then
 * it skips the secondary stack and redundancy functions. In redundant mode it waits
 * for both (primary and secondary) frames to come in. The result goes in an decision
 * tree that decides, depending on the route of the packet and its possible missing arrival,
 * how to reroute the original packet to get the data in an other try.
 *
 * @param[in] port        = port context struct
 * @param[in] idx = requested index of frame
 * @param[in] timer = absolute timeout time
 * @return Workcounter if a frame is found with corresponding index, otherwise
 * EC_NOFRAME.
 */
static int ecx_waitinframe_red(ecx_portt *port, int idx, osal_timert timer)
{
   int wkc  = EC_NOFRAME;
   int wkc2 = EC_NOFRAME;
   int primrx, secrx;

   /* if not in redundant mode then always assume secondary is OK */
   if (port->redstate == ECT_RED_NONE)
   {
      wkc2 = 0;
   }
   do
   {
      /* only read frame if not already in */
      if (wkc <= EC_NOFRAME)
      {
         wkc  = ecx_inframe(port, idx, 0);
      }
      /* only try secondary if in redundant mode */
      if (port->redstate != ECT_RED_NONE)
      {
         /* only read frame if not already in */
         if (wkc2 <= EC_NOFRAME)
            wkc2 = ecx_inframe(port, idx, 1);
      }
   /* wait for both frames to arrive or timeout */                       
    } while (((wkc <= EC_NOFRAME) || (wkc2 <= EC_NOFRAME)) && (osal_timer_is_expired(&timer) == FALSE));
      
   /* only do redundant functions when in redundant mode */
   if (port->redstate != ECT_RED_NONE)
   {
      /* primrx if the received MAC source on primary socket */
      primrx = 0;
      if (wkc > EC_NOFRAME)
      {
         primrx = port->rxsa[idx];
      }
      /* secrx if the received MAC source on psecondary socket */
      secrx = 0;
      if (wkc2 > EC_NOFRAME)
      {
         secrx = port->redport->rxsa[idx];
      }
      /* primary socket got secondary frame and secondary socket got primary frame */
      /* normal situation in redundant mode */
      if ( ((primrx == RX_SEC) && (secrx == RX_PRIM)) )
      {
         /* copy secondary buffer to primary */
         memcpy(&(port->rxbuf[idx]), &(port->redport->rxbuf[idx]), port->txbuflength[idx] - ETH_HEADERSIZE);
         wkc = wkc2;
      }
      /* primary socket got nothing or primary frame, and secondary socket got secondary frame */
      /* we need to resend TX packet */
      if ( ((primrx == 0) && (secrx == RX_SEC)) ||
           ((primrx == RX_PRIM) && (secrx == RX_SEC)) )
      {
         osal_timert read_timer;

         /* If both primary and secondary have partial connection retransmit the primary received
          * frame over the secondary socket. The result from the secondary received frame is a combined
          * frame that traversed all slaves in standard order. */
         if ( (primrx == RX_PRIM) && (secrx == RX_SEC) )
         {
            /* copy primary rx to tx buffer */
            memcpy(&(port->txbuf[idx][ETH_HEADERSIZE]), &(port->rxbuf[idx]), port->txbuflength[idx] - ETH_HEADERSIZE);
         }
         
         //osal_timer_start(&read_timer, EC_TIMEOUTRET);
  
                        osal_timer_start(&read_timer, 500);       
         
         /* resend secondary tx */
         ecx_outframe(port, idx, 1);
         do
         {
            /* retrieve frame */
            wkc2 = ecx_inframe(port, idx, 1);
         } while ((wkc2 <= EC_NOFRAME) && (osal_timer_is_expired(&read_timer) == FALSE));
         if (wkc2 > EC_NOFRAME)
         {
            /* copy secondary result to primary rx buffer */
            memcpy(&(port->rxbuf[idx]), &(port->redport->rxbuf[idx]), port->txbuflength[idx] - ETH_HEADERSIZE);
            wkc = wkc2;
         }
      }
   }

   /* return WKC or EC_NOFRAME */
   return wkc;
}

/** Blocking receive frame function. Calls ec_waitinframe_red().
 * @param[in] port        = port context struct
 * @param[in] idx       = requested index of frame
 * @param[in] timeout   = timeout in us
 * @return Workcounter if a frame is found with corresponding index, otherwise
 * EC_NOFRAME.
 */
int ecx_waitinframe(ecx_portt *port, int idx, int timeout)
{
   int wkc;
   
   osal_timert timer;
   osal_timer_start (&timer, timeout);
   wkc = ecx_waitinframe_red(port, idx, timer);

   return wkc;
}

/** Blocking send and receive frame function. Used for non processdata frames.
 * A datagram is build into a frame and transmitted via this function. It waits
 * for an answer and returns the workcounter. The function retries if time is
 * left and the result is WKC=0 or no frame received.
 *
 * The function calls ec_outframe_red() and ec_waitinframe_red().
 *
 * @param[in] port        = port context struct
 * @param[in] idx      = index of frame
 * @param[in] timeout  = timeout in us
 * @return Workcounter or EC_NOFRAME
 */
int ecx_srconfirm(ecx_portt *port, int idx, int timeout)
{
   int wkc = EC_NOFRAME;
   
   osal_timert timer;
   osal_timer_start(&timer, timeout);   
   
   do
   {
      osal_timert read_timer;

      /* tx frame on primary and if in redundant mode a dummy on secondary */
      ecx_outframe_red(port, idx);
      osal_timer_start(&read_timer, MIN(timeout, EC_TIMEOUTRET)); 
      
      /* get frame from primary or if in redundant mode possibly from secondary */
      wkc = ecx_waitinframe_red(port, idx, read_timer);
   /* wait for answer with WKC>0 or otherwise retry until timeout */
   } while ((wkc <= EC_NOFRAME) && (osal_timer_is_expired(&timer) == FALSE));

   return wkc;
}


#ifdef EC_VER1
int ec_setupnic(const char *ifname, int secondary)
{
   return ecx_setupnic(&ecx_port, ifname, secondary);
}

int ec_closenic(void)
{
   return ecx_closenic(&ecx_port);
}

int ec_getindex(void)
{
   return ecx_getindex(&ecx_port);
}

void ec_setbufstat(int idx, int bufstat)
{
   ecx_setbufstat(&ecx_port, idx, bufstat);
}

int ec_outframe(int idx, int stacknumber)
{
   return ecx_outframe(&ecx_port, idx, stacknumber);
}

int ec_outframe_red(int idx)
{
   return ecx_outframe_red(&ecx_port, idx);
}

int ec_inframe(int idx, int stacknumber)
{
   return ecx_inframe(&ecx_port, idx, stacknumber);
}

int ec_waitinframe(int idx, int timeout)
{
   return ecx_waitinframe(&ecx_port, idx, timeout);
}

int ec_srconfirm(int idx, int timeout)
{
   return ecx_srconfirm(&ecx_port, idx, timeout);
}
#endif