Cristian Castro
MPU9250 Basic Example Code
Diff: MPU9250.h
- Revision:
- 2:55ab1dcffe0c
- Parent:
- 1:fc94c7336b7c
--- a/MPU9250.h Fri Mar 01 09:47:40 2019 +0000
+++ b/MPU9250.h Fri Sep 03 04:53:40 2021 +0000
@@ -1,18 +1,8 @@
-/*****
- Library based on MPU-9250_Snowda library. It has been modified by Josué Olmeda Castelló for imasD Tecnología. It uses the
- mbed I2C class for comunications between the sensor and the master controller.
- Methods related with data filtering have not been tested.
- AD0 should be connected to GND.
- 04/05/2015
-*****/
-
#ifndef MPU9250_H
#define MPU9250_H
#include "mbed.h"
#include "math.h"
-
-#define M_PI 3.14159265358979323846
// See also MPU-9250 Register Map and Descriptions, Revision 4.0, RM-MPU-9250A-00, Rev. 1.4, 9/9/2013 for registers not listed in
// above document; the MPU9250 and MPU9150 are virtually identical but the latter has a different register map
@@ -198,10 +188,9 @@
uint8_t Mscale = MFS_16BITS; // MFS_14BITS or MFS_16BITS, 14-bit or 16-bit magnetometer resolution
uint8_t Mmode = 0x06; // Either 8 Hz 0x02) or 100 Hz (0x06) magnetometer data ODR
float aRes, gRes, mRes; // scale resolutions per LSB for the sensors
-int I2Cstate=1; // If I2Cstate!=0, I2C read or write operation has failed
//Set up I2C, (SDA,SCL)
-//I2C i2c(I2C_SDA, I2C_SCL);
+I2C i2c(I2C_SDA, I2C_SCL);
DigitalOut myled(LED1);
@@ -211,18 +200,12 @@
int16_t accelCount[3]; // Stores the 16-bit signed accelerometer sensor output
int16_t gyroCount[3]; // Stores the 16-bit signed gyro sensor output
int16_t magCount[3]; // Stores the 16-bit signed magnetometer sensor output
-int16_t minMagCount[3] = {INT16_MAX, INT16_MAX, INT16_MAX};
-int16_t maxMagCount[3] = {INT16_MIN, INT16_MIN, INT16_MIN}; // Stores the 16-bit signed magnetometer minimum and maximum sensor output
-
float magCalibration[3] = {0, 0, 0}, magbias[3] = {0, 0, 0}; // Factory mag calibration and mag bias
-float magScale[3] = {1, 1, 1}; // Magnetometer scalig for x, y and z axis
float gyroBias[3] = {0, 0, 0}, accelBias[3] = {0, 0, 0}; // Bias corrections for gyro and accelerometer
float ax, ay, az, gx, gy, gz, mx, my, mz; // variables to hold latest sensor data values
int16_t tempCount; // Stores the real internal chip temperature in degrees Celsius
float temperature;
float SelfTest[6];
-float orientation[1];
-float magn_x, magn_y;
int delt_t = 0; // used to control display output rate
int count = 0; // used to control display output rate
@@ -243,491 +226,456 @@
float eInt[3] = {0.0f, 0.0f, 0.0f}; // vector to hold integral error for Mahony method
class MPU9250 {
-
- private:
-
- I2C i2c;
-
+
protected:
public:
-
- MPU9250(I2C &i2c_ref) : i2c(i2c_ref)
- {
-
- }
-
- //===================================================================================================================
- //====== Set of useful function to access acceleration, gyroscope, and temperature data
- //===================================================================================================================
+ //===================================================================================================================
+//====== Set of useful function to access acceleratio, gyroscope, and temperature data
+//===================================================================================================================
void writeByte(uint8_t address, uint8_t subAddress, uint8_t data)
- {
- char data_write[2];
- data_write[0] = subAddress;
- data_write[1] = data;
- I2Cstate = i2c.write(address, data_write, 2, 0);
- }
+{
+ char data_write[2];
+ data_write[0] = subAddress;
+ data_write[1] = data;
+ i2c.write(address, data_write, 2, 0);
+}
char readByte(uint8_t address, uint8_t subAddress)
- {
- char data[1]; // `data` will store the register data
- char data_write[1];
- data_write[0] = subAddress;
- I2Cstate = i2c.write(address, data_write, 1, 1); // no stop
- I2Cstate = i2c.read(address, data, 1, 0);
- return data[0];
- }
-
- void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest) // count=nº of bytes to read / dest=destiny where data is stored
- {
- char data[14];
- char data_write[1];
- data_write[0] = subAddress;
- I2Cstate = i2c.write(address, data_write, 1, 1); // no stop
- I2Cstate = i2c.read(address, data, count, 0);
- for(int ii = 0; ii < count; ii++) {
- dest[ii] = data[ii];
- }
- }
-
- void getMres() {
- switch (Mscale)
- {
- // Possible magnetometer scales (and their register bit settings) are:
- // 14 bit resolution (0) and 16 bit resolution (1)
- case MFS_14BITS:
- mRes = 10.0*4219.0/8190.0; // Proper scale to return milliGauss
- break;
- case MFS_16BITS:
- mRes = 10.0*4219.0/32760.0; // Proper scale to return milliGauss
- break;
- }
- }
-
- void getGres() {
- switch (Gscale)
- {
- // Possible gyro scales (and their register bit settings) are:
- // 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS (11).
- // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:
- case GFS_250DPS:
- gRes = 250.0/32768.0;
- break;
- case GFS_500DPS:
- gRes = 500.0/32768.0;
- break;
- case GFS_1000DPS:
- gRes = 1000.0/32768.0;
- break;
- case GFS_2000DPS:
- gRes = 2000.0/32768.0;
- break;
- }
- }
-
- void getAres() {
- switch (Ascale)
- {
- // Possible accelerometer scales (and their register bit settings) are:
- // 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs (11).
- // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:
- case AFS_2G:
- aRes = 2.0/32768.0;
- break;
- case AFS_4G:
- aRes = 4.0/32768.0;
- break;
- case AFS_8G:
- aRes = 8.0/32768.0;
- break;
- case AFS_16G:
- aRes = 16.0/32768.0;
- break;
- }
- }
+{
+ char data[1]; // `data` will store the register data
+ char data_write[1];
+ data_write[0] = subAddress;
+ i2c.write(address, data_write, 1, 1); // no stop
+ i2c.read(address, data, 1, 0);
+ return data[0];
+}
- void readAccelData(int16_t * destination){
-
- uint8_t rawData[6]; // x/y/z accel register data stored here
- readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
- destination[0] = (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
- destination[1] = (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
- destination[2] = (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
- }
-
- void readGyroData(int16_t * destination){
- uint8_t rawData[6]; // x/y/z gyro register data stored here
- readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
- destination[0] = (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
- destination[1] = (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
- destination[2] = (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
- }
-
- void readMagData(int16_t * destination){
- uint8_t rawData[7]; // x/y/z gyro register data, ST2 register stored here, must read ST2 at end of data acquisition
- if(readByte(AK8963_ADDRESS, AK8963_ST1) & 0x01) { // wait for magnetometer data ready bit to be set
- readBytes(AK8963_ADDRESS, AK8963_XOUT_L, 7, &rawData[0]); // Read the six raw data and ST2 registers sequentially into data array
- uint8_t c = rawData[6]; // End data read by reading ST2 register
- if(!(c & 0x08)) { // Check if magnetic sensor overflow set, if not then report data
- destination[0] = (int16_t)(((int16_t)rawData[1] << 8) | rawData[0]); // Turn the MSB and LSB into a signed 16-bit value
- destination[1] = (int16_t)(((int16_t)rawData[3] << 8) | rawData[2]) ; // Data stored as little Endian
- destination[2] = (int16_t)(((int16_t)rawData[5] << 8) | rawData[4]) ;
- }
- }
- }
-
- int16_t readTempData(){
- uint8_t rawData[2]; // x/y/z gyro register data stored here
- readBytes(MPU9250_ADDRESS, TEMP_OUT_H, 2, &rawData[0]); // Read the two raw data registers sequentially into data array
- return (int16_t)(((int16_t)rawData[0]) << 8 | rawData[1]) ; // Turn the MSB and LSB into a 16-bit value
+ void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest)
+{
+ char data[14];
+ char data_write[1];
+ data_write[0] = subAddress;
+ i2c.write(address, data_write, 1, 1); // no stop
+ i2c.read(address, data, count, 0);
+ for(int ii = 0; ii < count; ii++) {
+ dest[ii] = data[ii];
}
-
- void resetMPU9250(){
- // reset device
- writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device
- wait(0.1);
- }
-
- void initAK8963(float * destination){
- // First extract the factory calibration for each magnetometer axis
- uint8_t rawData[3]; // x/y/z gyro calibration data stored here
- writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer
- wait(0.01);
- writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x0F); // Enter Fuse ROM access mode
- wait(0.01);
- readBytes(AK8963_ADDRESS, AK8963_ASAX, 3, &rawData[0]); // Read the x-, y-, and z-axis calibration values
- destination[0] = (float)(rawData[0] - 128)/256.0f + 1.0f; // Return x-axis sensitivity adjustment values, etc.
- destination[1] = (float)(rawData[1] - 128)/256.0f + 1.0f;
- destination[2] = (float)(rawData[2] - 128)/256.0f + 1.0f;
- writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer
- wait(0.01);
- // Configure the magnetometer for continuous read and highest resolution
- // set Mscale bit 4 to 1 (0) to enable 16 (14) bit resolution in CNTL register,
- // and enable continuous mode data acquisition Mmode (bits [3:0]), 0010 for 8 Hz and 0110 for 100 Hz sample rates
- writeByte(AK8963_ADDRESS, AK8963_CNTL, Mscale << 4 | Mmode); // Set magnetometer data resolution and sample ODR
- wait(0.01);
- }
-
- void initMPU9250(){
- // Initialize MPU9250 device
- // wake up device
- writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors
- wait(0.1); // Delay 100 ms for PLL to get established on x-axis gyro; should check for PLL ready interrupt
-
- // get stable time source
- writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01); // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001
-
- // Configure Gyro and Accelerometer
- // Disable FSYNC and set accelerometer and gyro bandwidth to 44 and 42 Hz, respectively;
- // DLPF_CFG = bits 2:0 = 010; this sets the sample rate at 1 kHz for both
- // Maximum delay is 4.9 ms which is just over a 200 Hz maximum rate
- writeByte(MPU9250_ADDRESS, CONFIG, 0x03);
-
- // Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)
- writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x04); // Use a 200 Hz rate; the same rate set in CONFIG above
+}
- // Set gyroscope full scale range
- // Range selects FS_SEL and AFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3
- uint8_t c = readByte(MPU9250_ADDRESS, GYRO_CONFIG);
- writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c & ~0xE0); // Clear self-test bits [7:5]
- writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c & ~0x18); // Clear AFS bits [4:3]
- writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c | Gscale << 3); // Set full scale range for the gyro
-
- // Set accelerometer configuration
- c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG);
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c & ~0xE0); // Clear self-test bits [7:5]
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c & ~0x18); // Clear AFS bits [4:3]
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c | Ascale << 3); // Set full scale range for the accelerometer
- // Set accelerometer sample rate configuration
- // It is possible to get a 4 kHz sample rate from the accelerometer by choosing 1 for
- // accel_fchoice_b bit [3]; in this case the bandwidth is 1.13 kHz
- c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG2);
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, c & ~0x0F); // Clear accel_fchoice_b (bit 3) and A_DLPFG (bits [2:0])
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, c | 0x03); // Set accelerometer rate to 1 kHz and bandwidth to 41 Hz
+void getMres() {
+ switch (Mscale)
+ {
+ // Possible magnetometer scales (and their register bit settings) are:
+ // 14 bit resolution (0) and 16 bit resolution (1)
+ case MFS_14BITS:
+ mRes = 10.0*4219.0/8190.0; // Proper scale to return milliGauss
+ break;
+ case MFS_16BITS:
+ mRes = 10.0*4219.0/32760.0; // Proper scale to return milliGauss
+ break;
+ }
+}
- // The accelerometer, gyro, and thermometer are set to 1 kHz sample rates,
- // but all these rates are further reduced by a factor of 5 to 200 Hz because of the SMPLRT_DIV setting
-
- // Configure Interrupts and Bypass Enable
- // Set interrupt pin active high, push-pull, and clear on read of INT_STATUS, enable I2C_BYPASS_EN so additional chips
- // can join the I2C bus and all can be controlled by the Arduino as master
- writeByte(MPU9250_ADDRESS, INT_PIN_CFG, 0x22);
- writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x01); // Enable data ready (bit 0) interrupt
- }
- // Function which accumulates gyro and accelerometer data after device initialization. It calculates the average
- // of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers.
- void calibrateMPU9250(float * dest1, float * dest2)
- {
- uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data
- uint16_t ii, packet_count, fifo_count;
- int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};
-
- // reset device, reset all registers, clear gyro and accelerometer bias registers
- writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device
- wait(0.1);
-
- // get stable time source
- // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001
- writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01);
- writeByte(MPU9250_ADDRESS, PWR_MGMT_2, 0x00);
- wait(0.2);
-
- // Configure device for bias calculation
- writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x00); // Disable all interrupts
- writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable FIFO
- writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Turn on internal clock source
- writeByte(MPU9250_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master
- writeByte(MPU9250_ADDRESS, USER_CTRL, 0x00); // Disable FIFO and I2C master modes
- writeByte(MPU9250_ADDRESS, USER_CTRL, 0x0C); // Reset FIFO and DMP
- wait(0.015);
-
- // Configure MPU9250 gyro and accelerometer for bias calculation
- writeByte(MPU9250_ADDRESS, CONFIG, 0x01); // Set low-pass filter to 188 Hz
- writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set sample rate to 1 kHz
- writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00); // Set gyro full-scale to 250 degrees per second, maximum sensitivity
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity
-
- uint16_t gyrosensitivity = 131; // = 131 LSB/degrees/sec
- uint16_t accelsensitivity = 16384; // = 16384 LSB/g
+void getGres() {
+ switch (Gscale)
+ {
+ // Possible gyro scales (and their register bit settings) are:
+ // 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS (11).
+ // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:
+ case GFS_250DPS:
+ gRes = 250.0/32768.0;
+ break;
+ case GFS_500DPS:
+ gRes = 500.0/32768.0;
+ break;
+ case GFS_1000DPS:
+ gRes = 1000.0/32768.0;
+ break;
+ case GFS_2000DPS:
+ gRes = 2000.0/32768.0;
+ break;
+ }
+}
+
- // Configure FIFO to capture accelerometer and gyro data. This data will be used for bias calculation
- writeByte(MPU9250_ADDRESS, USER_CTRL, 0x40); // Enable FIFO
- writeByte(MPU9250_ADDRESS, FIFO_EN, 0x78); // Enable gyro and accelerometer sensors for FIFO (max size 512 bytes in MPU-9250)
- wait(0.04); // accumulate 40 samples in 80 milliseconds = 480 bytes
+void getAres() {
+ switch (Ascale)
+ {
+ // Possible accelerometer scales (and their register bit settings) are:
+ // 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs (11).
+ // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:
+ case AFS_2G:
+ aRes = 2.0/32768.0;
+ break;
+ case AFS_4G:
+ aRes = 4.0/32768.0;
+ break;
+ case AFS_8G:
+ aRes = 8.0/32768.0;
+ break;
+ case AFS_16G:
+ aRes = 16.0/32768.0;
+ break;
+ }
+}
- // At end of sample accumulation, turn off FIFO sensor read
- writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable gyro and accelerometer sensors for FIFO
- readBytes(MPU9250_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count
- fifo_count = ((uint16_t)data[0] << 8) | data[1];
- packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging
- for (ii = 0; ii < packet_count; ii++) {
- int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};
- readBytes(MPU9250_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging
- accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1] ) ; // Form signed 16-bit integer for each sample in FIFO
- accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3] ) ;
- accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5] ) ;
- gyro_temp[0] = (int16_t) (((int16_t)data[6] << 8) | data[7] ) ;
- gyro_temp[1] = (int16_t) (((int16_t)data[8] << 8) | data[9] ) ;
- gyro_temp[2] = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;
-
- accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases
- accel_bias[1] += (int32_t) accel_temp[1];
- accel_bias[2] += (int32_t) accel_temp[2];
- gyro_bias[0] += (int32_t) gyro_temp[0];
- gyro_bias[1] += (int32_t) gyro_temp[1];
- gyro_bias[2] += (int32_t) gyro_temp[2];
-
- }
- accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases
- accel_bias[1] /= (int32_t) packet_count;
- accel_bias[2] /= (int32_t) packet_count;
- gyro_bias[0] /= (int32_t) packet_count;
- gyro_bias[1] /= (int32_t) packet_count;
- gyro_bias[2] /= (int32_t) packet_count;
-
- if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;} // Remove gravity from the z-axis accelerometer bias calculation
- else {accel_bias[2] += (int32_t) accelsensitivity;}
-
- // Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup
- data[0] = (-gyro_bias[0]/4 >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format
- data[1] = (-gyro_bias[0]/4) & 0xFF; // Biases are additive, so change sign on calculated average gyro biases
- data[2] = (-gyro_bias[1]/4 >> 8) & 0xFF;
- data[3] = (-gyro_bias[1]/4) & 0xFF;
- data[4] = (-gyro_bias[2]/4 >> 8) & 0xFF;
- data[5] = (-gyro_bias[2]/4) & 0xFF;
+void readAccelData(int16_t * destination)
+{
+ uint8_t rawData[6]; // x/y/z accel register data stored here
+ readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
+ destination[0] = (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
+ destination[1] = (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
+ destination[2] = (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
+}
- /// Push gyro biases to hardware registers
- /* writeByte(MPU9250_ADDRESS, XG_OFFSET_H, data[0]);
- writeByte(MPU9250_ADDRESS, XG_OFFSET_L, data[1]);
- writeByte(MPU9250_ADDRESS, YG_OFFSET_H, data[2]);
- writeByte(MPU9250_ADDRESS, YG_OFFSET_L, data[3]);
- writeByte(MPU9250_ADDRESS, ZG_OFFSET_H, data[4]);
- writeByte(MPU9250_ADDRESS, ZG_OFFSET_L, data[5]);
- */
- dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity; // construct gyro bias in deg/s for later manual subtraction
- dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity;
- dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;
+void readGyroData(int16_t * destination)
+{
+ uint8_t rawData[6]; // x/y/z gyro register data stored here
+ readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
+ destination[0] = (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
+ destination[1] = (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
+ destination[2] = (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
+}
+
+void readMagData(int16_t * destination)
+{
+ uint8_t rawData[7]; // x/y/z gyro register data, ST2 register stored here, must read ST2 at end of data acquisition
+ if(readByte(AK8963_ADDRESS, AK8963_ST1) & 0x01) { // wait for magnetometer data ready bit to be set
+ readBytes(AK8963_ADDRESS, AK8963_XOUT_L, 7, &rawData[0]); // Read the six raw data and ST2 registers sequentially into data array
+ uint8_t c = rawData[6]; // End data read by reading ST2 register
+ if(!(c & 0x08)) { // Check if magnetic sensor overflow set, if not then report data
+ destination[0] = (int16_t)(((int16_t)rawData[1] << 8) | rawData[0]); // Turn the MSB and LSB into a signed 16-bit value
+ destination[1] = (int16_t)(((int16_t)rawData[3] << 8) | rawData[2]) ; // Data stored as little Endian
+ destination[2] = (int16_t)(((int16_t)rawData[5] << 8) | rawData[4]) ;
+ }
+ }
+}
- // Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain
- // factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold
- // non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature
- // compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that
- // the accelerometer biases calculated above must be divided by 8.
+int16_t readTempData()
+{
+ uint8_t rawData[2]; // x/y/z gyro register data stored here
+ readBytes(MPU9250_ADDRESS, TEMP_OUT_H, 2, &rawData[0]); // Read the two raw data registers sequentially into data array
+ return (int16_t)(((int16_t)rawData[0]) << 8 | rawData[1]) ; // Turn the MSB and LSB into a 16-bit value
+}
- int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases
- readBytes(MPU9250_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values
- accel_bias_reg[0] = (int16_t) ((int16_t)data[0] << 8) | data[1];
- readBytes(MPU9250_ADDRESS, YA_OFFSET_H, 2, &data[0]);
- accel_bias_reg[1] = (int16_t) ((int16_t)data[0] << 8) | data[1];
- readBytes(MPU9250_ADDRESS, ZA_OFFSET_H, 2, &data[0]);
- accel_bias_reg[2] = (int16_t) ((int16_t)data[0] << 8) | data[1];
-
- uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers
- uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis
-
- for(ii = 0; ii < 3; ii++) {
- if(accel_bias_reg[ii] & mask) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit
- }
- // Construct total accelerometer bias, including calculated average accelerometer bias from above
- accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)
- accel_bias_reg[1] -= (accel_bias[1]/8);
- accel_bias_reg[2] -= (accel_bias[2]/8);
-
- data[0] = (accel_bias_reg[0] >> 8) & 0xFF;
- data[1] = (accel_bias_reg[0]) & 0xFF;
- data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers
- data[2] = (accel_bias_reg[1] >> 8) & 0xFF;
- data[3] = (accel_bias_reg[1]) & 0xFF;
- data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers
- data[4] = (accel_bias_reg[2] >> 8) & 0xFF;
- data[5] = (accel_bias_reg[2]) & 0xFF;
- data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers
-
- // Apparently this is not working for the acceleration biases in the MPU-9250
- // Are we handling the temperature correction bit properly?
- // Push accelerometer biases to hardware registers
- /* writeByte(MPU9250_ADDRESS, XA_OFFSET_H, data[0]);
- writeByte(MPU9250_ADDRESS, XA_OFFSET_L, data[1]);
- writeByte(MPU9250_ADDRESS, YA_OFFSET_H, data[2]);
- writeByte(MPU9250_ADDRESS, YA_OFFSET_L, data[3]);
- writeByte(MPU9250_ADDRESS, ZA_OFFSET_H, data[4]);
- writeByte(MPU9250_ADDRESS, ZA_OFFSET_L, data[5]);
- */
- // Output scaled accelerometer biases for manual subtraction in the main program
- dest2[0] = (float)accel_bias[0]/(float)accelsensitivity;
- dest2[1] = (float)accel_bias[1]/(float)accelsensitivity;
- dest2[2] = (float)accel_bias[2]/(float)accelsensitivity;
- }
+void resetMPU9250() {
+ // reset device
+ writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device
+ wait(0.1);
+ }
+
+ void initAK8963(float * destination)
+{
+ // First extract the factory calibration for each magnetometer axis
+ uint8_t rawData[3]; // x/y/z gyro calibration data stored here
+ writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer
+ wait(0.01);
+ writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x0F); // Enter Fuse ROM access mode
+ wait(0.01);
+ readBytes(AK8963_ADDRESS, AK8963_ASAX, 3, &rawData[0]); // Read the x-, y-, and z-axis calibration values
+ destination[0] = (float)(rawData[0] - 128)/256.0f + 1.0f; // Return x-axis sensitivity adjustment values, etc.
+ destination[1] = (float)(rawData[1] - 128)/256.0f + 1.0f;
+ destination[2] = (float)(rawData[2] - 128)/256.0f + 1.0f;
+ writeByte(AK8963_ADDRESS, AK8963_CNTL, 0x00); // Power down magnetometer
+ wait(0.01);
+ // Configure the magnetometer for continuous read and highest resolution
+ // set Mscale bit 4 to 1 (0) to enable 16 (14) bit resolution in CNTL register,
+ // and enable continuous mode data acquisition Mmode (bits [3:0]), 0010 for 8 Hz and 0110 for 100 Hz sample rates
+ writeByte(AK8963_ADDRESS, AK8963_CNTL, Mscale << 4 | Mmode); // Set magnetometer data resolution and sample ODR
+ wait(0.01);
+}
- // Accelerometer and gyroscope self test; check calibration wrt factory settings
- void MPU9250SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass
- {
- uint8_t rawData[6] = {0, 0, 0, 0, 0, 0};
- uint8_t selfTest[6];
- int16_t gAvg[3], aAvg[3], aSTAvg[3], gSTAvg[3];
- float factoryTrim[6];
- uint8_t FS = 0;
+void initMPU9250()
+{
+ // Initialize MPU9250 device
+ // wake up device
+ writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors
+ wait(0.1); // Delay 100 ms for PLL to get established on x-axis gyro; should check for PLL ready interrupt
+
+ // get stable time source
+ writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01); // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001
+
+ // Configure Gyro and Accelerometer
+ // Disable FSYNC and set accelerometer and gyro bandwidth to 44 and 42 Hz, respectively;
+ // DLPF_CFG = bits 2:0 = 010; this sets the sample rate at 1 kHz for both
+ // Maximum delay is 4.9 ms which is just over a 200 Hz maximum rate
+ writeByte(MPU9250_ADDRESS, CONFIG, 0x03);
+
+ // Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)
+ writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x04); // Use a 200 Hz rate; the same rate set in CONFIG above
+
+ // Set gyroscope full scale range
+ // Range selects FS_SEL and AFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3
+ uint8_t c = readByte(MPU9250_ADDRESS, GYRO_CONFIG);
+ writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c & ~0xE0); // Clear self-test bits [7:5]
+ writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c & ~0x18); // Clear AFS bits [4:3]
+ writeByte(MPU9250_ADDRESS, GYRO_CONFIG, c | Gscale << 3); // Set full scale range for the gyro
- writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set gyro sample rate to 1 kHz
- writeByte(MPU9250_ADDRESS, CONFIG, 0x02); // Set gyro sample rate to 1 kHz and DLPF to 92 Hz
- writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 1<<FS); // Set full scale range for the gyro to 250 dps
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, 0x02); // Set accelerometer rate to 1 kHz and bandwidth to 92 Hz
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 1<<FS); // Set full scale range for the accelerometer to 2 g
+ // Set accelerometer configuration
+ c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG);
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c & ~0xE0); // Clear self-test bits [7:5]
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c & ~0x18); // Clear AFS bits [4:3]
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, c | Ascale << 3); // Set full scale range for the accelerometer
+
+ // Set accelerometer sample rate configuration
+ // It is possible to get a 4 kHz sample rate from the accelerometer by choosing 1 for
+ // accel_fchoice_b bit [3]; in this case the bandwidth is 1.13 kHz
+ c = readByte(MPU9250_ADDRESS, ACCEL_CONFIG2);
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, c & ~0x0F); // Clear accel_fchoice_b (bit 3) and A_DLPFG (bits [2:0])
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, c | 0x03); // Set accelerometer rate to 1 kHz and bandwidth to 41 Hz
- for( int ii = 0; ii < 200; ii++) { // get average current values of gyro and acclerometer
+ // The accelerometer, gyro, and thermometer are set to 1 kHz sample rates,
+ // but all these rates are further reduced by a factor of 5 to 200 Hz because of the SMPLRT_DIV setting
+
+ // Configure Interrupts and Bypass Enable
+ // Set interrupt pin active high, push-pull, and clear on read of INT_STATUS, enable I2C_BYPASS_EN so additional chips
+ // can join the I2C bus and all can be controlled by the Arduino as master
+ writeByte(MPU9250_ADDRESS, INT_PIN_CFG, 0x22);
+ writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x01); // Enable data ready (bit 0) interrupt
+}
+
+// Function which accumulates gyro and accelerometer data after device initialization. It calculates the average
+// of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers.
+void calibrateMPU9250(float * dest1, float * dest2)
+{
+ uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data
+ uint16_t ii, packet_count, fifo_count;
+ int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};
- readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
- aAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
- aAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
- aAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
-
- readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
- gAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
- gAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
- gAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
- }
+// reset device, reset all registers, clear gyro and accelerometer bias registers
+ writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device
+ wait(0.1);
+
+// get stable time source
+// Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001
+ writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x01);
+ writeByte(MPU9250_ADDRESS, PWR_MGMT_2, 0x00);
+ wait(0.2);
- for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average current readings
- aAvg[ii] /= 200;
- gAvg[ii] /= 200;
- }
-
- // Configure the accelerometer for self-test
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0xE0); // Enable self test on all three axes and set accelerometer range to +/- 2 g
- writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s
- wait_ms(25); // Delay a while to let the device stabilize
-
- for( int ii = 0; ii < 200; ii++) { // get average self-test values of gyro and acclerometer
+// Configure device for bias calculation
+ writeByte(MPU9250_ADDRESS, INT_ENABLE, 0x00); // Disable all interrupts
+ writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable FIFO
+ writeByte(MPU9250_ADDRESS, PWR_MGMT_1, 0x00); // Turn on internal clock source
+ writeByte(MPU9250_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master
+ writeByte(MPU9250_ADDRESS, USER_CTRL, 0x00); // Disable FIFO and I2C master modes
+ writeByte(MPU9250_ADDRESS, USER_CTRL, 0x0C); // Reset FIFO and DMP
+ wait(0.015);
- readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
- aSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
- aSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
- aSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
-
- readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
- gSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
- gSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
- gSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
- }
-
- for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average self-test readings
- aSTAvg[ii] /= 200;
- gSTAvg[ii] /= 200;
- }
+// Configure MPU9250 gyro and accelerometer for bias calculation
+ writeByte(MPU9250_ADDRESS, CONFIG, 0x01); // Set low-pass filter to 188 Hz
+ writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set sample rate to 1 kHz
+ writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00); // Set gyro full-scale to 250 degrees per second, maximum sensitivity
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity
+
+ uint16_t gyrosensitivity = 131; // = 131 LSB/degrees/sec
+ uint16_t accelsensitivity = 16384; // = 16384 LSB/g
+
+// Configure FIFO to capture accelerometer and gyro data for bias calculation
+ writeByte(MPU9250_ADDRESS, USER_CTRL, 0x40); // Enable FIFO
+ writeByte(MPU9250_ADDRESS, FIFO_EN, 0x78); // Enable gyro and accelerometer sensors for FIFO (max size 512 bytes in MPU-9250)
+ wait(0.04); // accumulate 40 samples in 80 milliseconds = 480 bytes
+
+// At end of sample accumulation, turn off FIFO sensor read
+ writeByte(MPU9250_ADDRESS, FIFO_EN, 0x00); // Disable gyro and accelerometer sensors for FIFO
+ readBytes(MPU9250_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count
+ fifo_count = ((uint16_t)data[0] << 8) | data[1];
+ packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging
+
+ for (ii = 0; ii < packet_count; ii++) {
+ int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};
+ readBytes(MPU9250_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging
+ accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1] ) ; // Form signed 16-bit integer for each sample in FIFO
+ accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3] ) ;
+ accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5] ) ;
+ gyro_temp[0] = (int16_t) (((int16_t)data[6] << 8) | data[7] ) ;
+ gyro_temp[1] = (int16_t) (((int16_t)data[8] << 8) | data[9] ) ;
+ gyro_temp[2] = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;
+
+ accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases
+ accel_bias[1] += (int32_t) accel_temp[1];
+ accel_bias[2] += (int32_t) accel_temp[2];
+ gyro_bias[0] += (int32_t) gyro_temp[0];
+ gyro_bias[1] += (int32_t) gyro_temp[1];
+ gyro_bias[2] += (int32_t) gyro_temp[2];
+
+}
+ accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases
+ accel_bias[1] /= (int32_t) packet_count;
+ accel_bias[2] /= (int32_t) packet_count;
+ gyro_bias[0] /= (int32_t) packet_count;
+ gyro_bias[1] /= (int32_t) packet_count;
+ gyro_bias[2] /= (int32_t) packet_count;
+
+ if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;} // Remove gravity from the z-axis accelerometer bias calculation
+ else {accel_bias[2] += (int32_t) accelsensitivity;}
+
+// Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup
+ data[0] = (-gyro_bias[0]/4 >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format
+ data[1] = (-gyro_bias[0]/4) & 0xFF; // Biases are additive, so change sign on calculated average gyro biases
+ data[2] = (-gyro_bias[1]/4 >> 8) & 0xFF;
+ data[3] = (-gyro_bias[1]/4) & 0xFF;
+ data[4] = (-gyro_bias[2]/4 >> 8) & 0xFF;
+ data[5] = (-gyro_bias[2]/4) & 0xFF;
+
+/// Push gyro biases to hardware registers
+/* writeByte(MPU9250_ADDRESS, XG_OFFSET_H, data[0]);
+ writeByte(MPU9250_ADDRESS, XG_OFFSET_L, data[1]);
+ writeByte(MPU9250_ADDRESS, YG_OFFSET_H, data[2]);
+ writeByte(MPU9250_ADDRESS, YG_OFFSET_L, data[3]);
+ writeByte(MPU9250_ADDRESS, ZG_OFFSET_H, data[4]);
+ writeByte(MPU9250_ADDRESS, ZG_OFFSET_L, data[5]);
+*/
+ dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity; // construct gyro bias in deg/s for later manual subtraction
+ dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity;
+ dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;
+
+// Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain
+// factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold
+// non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature
+// compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that
+// the accelerometer biases calculated above must be divided by 8.
+
+ int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases
+ readBytes(MPU9250_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values
+ accel_bias_reg[0] = (int16_t) ((int16_t)data[0] << 8) | data[1];
+ readBytes(MPU9250_ADDRESS, YA_OFFSET_H, 2, &data[0]);
+ accel_bias_reg[1] = (int16_t) ((int16_t)data[0] << 8) | data[1];
+ readBytes(MPU9250_ADDRESS, ZA_OFFSET_H, 2, &data[0]);
+ accel_bias_reg[2] = (int16_t) ((int16_t)data[0] << 8) | data[1];
- // Configure the gyro and accelerometer for normal operation
- writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00);
- writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00);
- //delay(25); // Delay a while to let the device stabilize
- wait_ms(25); // Delay a while to let the device stabilize
-
- // Retrieve accelerometer and gyro factory Self-Test Code from USR_Reg
- selfTest[0] = readByte(MPU9250_ADDRESS, SELF_TEST_X_ACCEL); // X-axis accel self-test results
- selfTest[1] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_ACCEL); // Y-axis accel self-test results
- selfTest[2] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_ACCEL); // Z-axis accel self-test results
- selfTest[3] = readByte(MPU9250_ADDRESS, SELF_TEST_X_GYRO); // X-axis gyro self-test results
- selfTest[4] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_GYRO); // Y-axis gyro self-test results
- selfTest[5] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_GYRO); // Z-axis gyro self-test results
+ uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers
+ uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis
+
+ for(ii = 0; ii < 3; ii++) {
+ if(accel_bias_reg[ii] & mask) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit
+ }
- // Retrieve factory self-test value from self-test code reads
- factoryTrim[0] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[0] - 1.0) )); // FT[Xa] factory trim calculation
- factoryTrim[1] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[1] - 1.0) )); // FT[Ya] factory trim calculation
- factoryTrim[2] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[2] - 1.0) )); // FT[Za] factory trim calculation
- factoryTrim[3] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[3] - 1.0) )); // FT[Xg] factory trim calculation
- factoryTrim[4] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[4] - 1.0) )); // FT[Yg] factory trim calculation
- factoryTrim[5] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[5] - 1.0) )); // FT[Zg] factory trim calculation
+ // Construct total accelerometer bias, including calculated average accelerometer bias from above
+ accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)
+ accel_bias_reg[1] -= (accel_bias[1]/8);
+ accel_bias_reg[2] -= (accel_bias[2]/8);
- // Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response
- // To get percent, must multiply by 100
- for (int i = 0; i < 3; i++) {
- destination[i] = 100.0*((float)(aSTAvg[i] - aAvg[i]))/factoryTrim[i]; // Report percent differences
- destination[i+3] = 100.0*((float)(gSTAvg[i] - gAvg[i]))/factoryTrim[i+3]; // Report percent differences
- }
- }
+ data[0] = (accel_bias_reg[0] >> 8) & 0xFF;
+ data[1] = (accel_bias_reg[0]) & 0xFF;
+ data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers
+ data[2] = (accel_bias_reg[1] >> 8) & 0xFF;
+ data[3] = (accel_bias_reg[1]) & 0xFF;
+ data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers
+ data[4] = (accel_bias_reg[2] >> 8) & 0xFF;
+ data[5] = (accel_bias_reg[2]) & 0xFF;
+ data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers
+
+// Apparently this is not working for the acceleration biases in the MPU-9250
+// Are we handling the temperature correction bit properly?
+// Push accelerometer biases to hardware registers
+/* writeByte(MPU9250_ADDRESS, XA_OFFSET_H, data[0]);
+ writeByte(MPU9250_ADDRESS, XA_OFFSET_L, data[1]);
+ writeByte(MPU9250_ADDRESS, YA_OFFSET_H, data[2]);
+ writeByte(MPU9250_ADDRESS, YA_OFFSET_L, data[3]);
+ writeByte(MPU9250_ADDRESS, ZA_OFFSET_H, data[4]);
+ writeByte(MPU9250_ADDRESS, ZA_OFFSET_L, data[5]);
+*/
+// Output scaled accelerometer biases for manual subtraction in the main program
+ dest2[0] = (float)accel_bias[0]/(float)accelsensitivity;
+ dest2[1] = (float)accel_bias[1]/(float)accelsensitivity;
+ dest2[2] = (float)accel_bias[2]/(float)accelsensitivity;
+}
-
- void getCompassOrientation(float * orient){ // Obtains the orientation of the device in degrees. 0 degrees North. 180 degrees South.
- /*
- Remember that it is the earth's rotational axis that defines the geographic north and south poles that we use for map references.
- It turns out that there is a discrepancy of about 11.5 degrees between the geographic poles and the magnetic poles. The last is
- what the magnetometer will read. A value, called the declination angle, can be applied to the magnetic direction to correct for this.
- On Valencia (Spain) this value is about 0 degrees.
- */
-
- // First of all measure 3 axis magnetometer values (only X and Y axis is used):
- readMagData(magCount); // Read the x/y/z adc values
- // Calculate the magnetometer values in milliGauss
- // Include factory calibration per data sheet and user environmental corrections
- if (I2Cstate == 0){ // no error on I2C
- I2Cstate = 1;
- magn_x = (float)magCount[0]*mRes*magCalibration[0] - magbias[0]; // get actual magnetometer value, this depends on scale being set
- magn_y = (float)magCount[1]*mRes*magCalibration[1] - magbias[1];
- }
-
- // Now obtains the orientation value:
- if (magn_y>0)
- orient[0] = 90.0 - (float) ( atan(magn_x/magn_y)*180/M_PI );
- else if (magn_y<0)
- orient[0] = 270.0 - (float) ( atan(magn_x/magn_y)*180/M_PI );
- else if (magn_y == 0){
- if (magn_x<0)
- orient[0] = 180.0;
- else
- orient[0] = 0.0;
- }
- }
+// Accelerometer and gyroscope self test; check calibration wrt factory settings
+void MPU9250SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass
+{
+ uint8_t rawData[6] = {0, 0, 0, 0, 0, 0};
+ uint8_t selfTest[6];
+ int16_t gAvg[3], aAvg[3], aSTAvg[3], gSTAvg[3];
+ float factoryTrim[6];
+ uint8_t FS = 0;
+
+ writeByte(MPU9250_ADDRESS, SMPLRT_DIV, 0x00); // Set gyro sample rate to 1 kHz
+ writeByte(MPU9250_ADDRESS, CONFIG, 0x02); // Set gyro sample rate to 1 kHz and DLPF to 92 Hz
+ writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 1<<FS); // Set full scale range for the gyro to 250 dps
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG2, 0x02); // Set accelerometer rate to 1 kHz and bandwidth to 92 Hz
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 1<<FS); // Set full scale range for the accelerometer to 2 g
+
+ for( int ii = 0; ii < 200; ii++) { // get average current values of gyro and acclerometer
+
+ readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
+ aAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
+ aAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
+ aAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
+
+ readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
+ gAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
+ gAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
+ gAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
+ }
+
+ for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average current readings
+ aAvg[ii] /= 200;
+ gAvg[ii] /= 200;
+ }
+
+// Configure the accelerometer for self-test
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0xE0); // Enable self test on all three axes and set accelerometer range to +/- 2 g
+ writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s
+ wait_ms(25); // Delay a while to let the device stabilize
-
-
-
-
+ for( int ii = 0; ii < 200; ii++) { // get average self-test values of gyro and acclerometer
+
+ readBytes(MPU9250_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]); // Read the six raw data registers into data array
+ aSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
+ aSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
+ aSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
+
+ readBytes(MPU9250_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]); // Read the six raw data registers sequentially into data array
+ gSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ; // Turn the MSB and LSB into a signed 16-bit value
+ gSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;
+ gSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ;
+ }
+
+ for (int ii =0; ii < 3; ii++) { // Get average of 200 values and store as average self-test readings
+ aSTAvg[ii] /= 200;
+ gSTAvg[ii] /= 200;
+ }
+
+ // Configure the gyro and accelerometer for normal operation
+ writeByte(MPU9250_ADDRESS, ACCEL_CONFIG, 0x00);
+ writeByte(MPU9250_ADDRESS, GYRO_CONFIG, 0x00);
+ wait_ms(25); // Delay a while to let the device stabilize
+
+ // Retrieve accelerometer and gyro factory Self-Test Code from USR_Reg
+ selfTest[0] = readByte(MPU9250_ADDRESS, SELF_TEST_X_ACCEL); // X-axis accel self-test results
+ selfTest[1] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_ACCEL); // Y-axis accel self-test results
+ selfTest[2] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_ACCEL); // Z-axis accel self-test results
+ selfTest[3] = readByte(MPU9250_ADDRESS, SELF_TEST_X_GYRO); // X-axis gyro self-test results
+ selfTest[4] = readByte(MPU9250_ADDRESS, SELF_TEST_Y_GYRO); // Y-axis gyro self-test results
+ selfTest[5] = readByte(MPU9250_ADDRESS, SELF_TEST_Z_GYRO); // Z-axis gyro self-test results
+
+ // Retrieve factory self-test value from self-test code reads
+ factoryTrim[0] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[0] - 1.0) )); // FT[Xa] factory trim calculation
+ factoryTrim[1] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[1] - 1.0) )); // FT[Ya] factory trim calculation
+ factoryTrim[2] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[2] - 1.0) )); // FT[Za] factory trim calculation
+ factoryTrim[3] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[3] - 1.0) )); // FT[Xg] factory trim calculation
+ factoryTrim[4] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[4] - 1.0) )); // FT[Yg] factory trim calculation
+ factoryTrim[5] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[5] - 1.0) )); // FT[Zg] factory trim calculation
+
+ // Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response
+ // To get percent, must multiply by 100
+ for (int i = 0; i < 3; i++) {
+ destination[i] = 100.0*((float)(aSTAvg[i] - aAvg[i]))/factoryTrim[i]; // Report percent differences
+ destination[i+3] = 100.0*((float)(gSTAvg[i] - gAvg[i]))/factoryTrim[i+3]; // Report percent differences
+ }
+
+}
+
+
// Implementation of Sebastian Madgwick's "...efficient orientation filter for... inertial/magnetic sensor arrays"
// (see http://www.x-io.co.uk/category/open-source/ for examples and more details)