File content as of revision 0:3214e3bbf25c:

#ifndef MCP_4725_H
#define MCP_4725_H

#include "stdbool.h"
#include "mbed.h"
#include "I2C.h"


/** MCP4725 class.
 *  Used for interfacing with a mcp4725 12-Bit Digital-to-Analog Converter.
 */
class MCP4725
{
    public:
    /** The device supports two types of power modes: normal and power-down. In normal mode the device
     * operates a normal digital to analog conversion. In power-down mode all digitial to analog  
     * conversion is stopped, resulting in the device using less power (typically 60nA). Also, in power 
     * down mode Vout will be pulled to ground using either a 1k, 100k or 500k ohm internal resistors. */
    enum PowerMode {
        /** In normal mode the device operates a normal D2A conversion. */
        Normal=0,
        /** Enter the device into a power down mode, and pull Vout to ground using an internal 1k resistor. */
        PowerDown1k=1,
        /** Enter the device into a power down mode, and pull Vout to ground using an internal 100k resistor. */
        PowerDown100k=2,
        /** Enter the device into a power down mode, and pull Vout to ground using an internal 500k resistor. */
        PowerDown500k=3
    };
    
    /** The device supports 3 different I2C bus frequencies.*/
    enum BusFrequency {
        /** Standard 100kHz bus. */
        Standard100kHz,
        /** Fast 400kHz bus. */
        Fast400kHz,
        /** High Speed 3.4Mhz bus. */
        HighSpeed3_4Mhz
    };
    
    /** Create an mcp4725 I2C interface
     * 
     * @param sda I2C data line pin
     * @param scl I2C clock line pin
     * @param bus_frequency the frequency at which the I2C bus is running.
     * @param device_address_bits The 3bit address bits of the device.
     */
    MCP4725(PinName sda, PinName scl, BusFrequency bus_frequency, int device_address_bits);
    
    
    /* Update the power mode and DAC value.
     *
     * @param   mode The Power mode to set the device into.
     * @param   dac_value The 12bit dac register data value.
     * @param   writeToEeprom True if the config is to be stored 
     *          in eeprom, otherwise false
     * 
     * @returns 
     *       0 on success,
     *   non-0 on failure
     */
    int write(enum PowerMode mode, int dac_value, bool writeToEeprom);
    
        
    /** Read the contents of the dac register, the contents of eeprom, and if an eeprom write is currently active.
     * 
     * @param   mode Pointer to variable to store the current power mode.
     * @param   mode_eeprom Pointer to variable to store the power mode as is stored in eeprom.
     * @param   dac_value Pointer to variable to store the current dac value.
     * @param   dac_value_eeprom Pointer to variable to store the dac value as is stored in eeprom.
     * @param   eeprom_write_in_progress Pointer to variable to store the current eeprom write status.
     *
     * @returns 
     *       0 on success,
     *   non-0 on failure
     */
    int read(enum PowerMode* mode, enum PowerMode* mode_eeprom, int* dac_value, int* dac_value_eeprom, bool* eeprom_write_in_progress);
    
    protected:
    /** mbed I2C interface driver. */
    I2C * _i2c_interface;
    /** The full i2c device address. */
    int _device_address;
    
};

#endif