Fork of Smoothie to port to mbed non-LPC targets.
Fork of Smoothie by
Diff: libs/LPC17xx/LPC17xxLib/src/lpc17xx_i2c.c
- Revision:
- 2:1df0b61d3b5a
diff -r ab59fc9af055 -r 1df0b61d3b5a libs/LPC17xx/LPC17xxLib/src/lpc17xx_i2c.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/libs/LPC17xx/LPC17xxLib/src/lpc17xx_i2c.c Fri Feb 28 18:52:52 2014 -0800 @@ -0,0 +1,1383 @@ +#ifdef __LPC17XX__ + +/********************************************************************** +* $Id$ lpc17xx_gpio.c 2011-03-31 +*//** +* @file lpc17xx_gpio.c +* @brief Contains all functions support for I2C firmware +* library on LPC17xx +* @version 2.1 +* @date 31. Mar. 2011 +* @author NXP MCU SW Application Team +* +* Copyright(C) 2010, NXP Semiconductor +* All rights reserved. +* +*********************************************************************** +* Software that is described herein is for illustrative purposes only +* which provides customers with programming information regarding the +* products. This software is supplied "AS IS" without any warranties. +* NXP Semiconductors assumes no responsibility or liability for the +* use of the software, conveys no license or title under any patent, +* copyright, or mask work right to the product. NXP Semiconductors +* reserves the right to make changes in the software without +* notification. NXP Semiconductors also make no representation or +* warranty that such application will be suitable for the specified +* use without further testing or modification. +**********************************************************************/ + +/* Peripheral group ----------------------------------------------------------- */ +/** @addtogroup I2C + * @{ + */ + +/* Includes ------------------------------------------------------------------- */ +#include "lpc17xx_i2c.h" +#include "lpc17xx_clkpwr.h" +#include "lpc17xx_pinsel.h" + + +/* If this source file built with example, the LPC17xx FW library configuration + * file in each example directory ("lpc17xx_libcfg.h") must be included, + * otherwise the default FW library configuration file must be included instead + */ +#ifdef __BUILD_WITH_EXAMPLE__ +#include "lpc17xx_libcfg.h" +#else +#include "lpc17xx_libcfg_default.h" +#endif /* __BUILD_WITH_EXAMPLE__ */ + + +#ifdef _I2C + + +/* Private Types -------------------------------------------------------------- */ +/** @defgroup I2C_Private_Types I2C Private Types + * @{ + */ + +/** + * @brief I2C device configuration structure type + */ +typedef struct +{ + uint32_t txrx_setup; /* Transmission setup */ + int32_t dir; /* Current direction phase, 0 - write, 1 - read */ +} I2C_CFG_T; + +/** + * @} + */ + +/* Private Variables ---------------------------------------------------------- */ +/** + * @brief II2C driver data for I2C0, I2C1 and I2C2 + */ +static I2C_CFG_T i2cdat[3]; + +static uint32_t I2C_MasterComplete[3]; +static uint32_t I2C_SlaveComplete[3]; + +static uint32_t I2C_MonitorBufferIndex; + +/* Private Functions ---------------------------------------------------------- */ + +/* Get I2C number */ +static int32_t I2C_getNum(LPC_I2C_TypeDef *I2Cx); + +/* Generate a start condition on I2C bus (in master mode only) */ +static uint32_t I2C_Start (LPC_I2C_TypeDef *I2Cx); + +/* Generate a stop condition on I2C bus (in master mode only) */ +static void I2C_Stop (LPC_I2C_TypeDef *I2Cx); + +/* I2C send byte subroutine */ +static uint32_t I2C_SendByte (LPC_I2C_TypeDef *I2Cx, uint8_t databyte); + +/* I2C get byte subroutine */ +static uint32_t I2C_GetByte (LPC_I2C_TypeDef *I2Cx, uint8_t *retdat, Bool ack); + +/* I2C set clock (hz) */ +static void I2C_SetClock (LPC_I2C_TypeDef *I2Cx, uint32_t target_clock); + +/*--------------------------------------------------------------------------------*/ +/********************************************************************//** + * @brief Convert from I2C peripheral to number + * @param[in] I2Cx: I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return I2C number, could be: 0..2 + *********************************************************************/ +static int32_t I2C_getNum(LPC_I2C_TypeDef *I2Cx){ + if (I2Cx == LPC_I2C0) { + return (0); + } else if (I2Cx == LPC_I2C1) { + return (1); + } else if (I2Cx == LPC_I2C2) { + return (2); + } + return (-1); +} + +/********************************************************************//** + * @brief Generate a start condition on I2C bus (in master mode only) + * @param[in] I2Cx: I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return value of I2C status register after generate a start condition + *********************************************************************/ +static uint32_t I2C_Start (LPC_I2C_TypeDef *I2Cx) +{ + I2Cx->I2CONSET = I2C_I2CONSET_STA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + + // Wait for complete + while (!(I2Cx->I2CONSET & I2C_I2CONSET_SI)); + I2Cx->I2CONCLR = I2C_I2CONCLR_STAC; + return (I2Cx->I2STAT & I2C_STAT_CODE_BITMASK); +} + +/********************************************************************//** + * @brief Generate a stop condition on I2C bus (in master mode only) + * @param[in] I2Cx: I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return None + *********************************************************************/ +static void I2C_Stop (LPC_I2C_TypeDef *I2Cx) +{ + + /* Make sure start bit is not active */ + if (I2Cx->I2CONSET & I2C_I2CONSET_STA) + { + I2Cx->I2CONCLR = I2C_I2CONCLR_STAC; + } + I2Cx->I2CONSET = I2C_I2CONSET_STO; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; +} + +/********************************************************************//** + * @brief Send a byte + * @param[in] I2Cx: I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] databyte: number of byte + * @return value of I2C status register after sending + *********************************************************************/ +static uint32_t I2C_SendByte (LPC_I2C_TypeDef *I2Cx, uint8_t databyte) +{ + /* Make sure start bit is not active */ + if (I2Cx->I2CONSET & I2C_I2CONSET_STA) + { + I2Cx->I2CONCLR = I2C_I2CONCLR_STAC; + } + I2Cx->I2DAT = databyte & I2C_I2DAT_BITMASK; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + + while (!(I2Cx->I2CONSET & I2C_I2CONSET_SI)); + return (I2Cx->I2STAT & I2C_STAT_CODE_BITMASK); +} + +/********************************************************************//** + * @brief Get a byte + * @param[in] I2Cx: I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[out] retdat pointer to return data + * @param[in] ack assert acknowledge or not, should be: TRUE/FALSE + * @return value of I2C status register after sending + *********************************************************************/ +static uint32_t I2C_GetByte (LPC_I2C_TypeDef *I2Cx, uint8_t *retdat, Bool ack) +{ + if (ack == TRUE) + { + I2Cx->I2CONSET = I2C_I2CONSET_AA; + } + else + { + I2Cx->I2CONCLR = I2C_I2CONCLR_AAC; + } + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + + while (!(I2Cx->I2CONSET & I2C_I2CONSET_SI)); + *retdat = (uint8_t) (I2Cx->I2DAT & I2C_I2DAT_BITMASK); + return (I2Cx->I2STAT & I2C_STAT_CODE_BITMASK); +} + +/*********************************************************************//** + * @brief Setup clock rate for I2C peripheral + * @param[in] I2Cx I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] target_clock : clock of SSP (Hz) + * @return None + ***********************************************************************/ +static void I2C_SetClock (LPC_I2C_TypeDef *I2Cx, uint32_t target_clock) +{ + uint32_t temp = 0; + + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + + // Get PCLK of I2C controller + if (I2Cx == LPC_I2C0) + { + temp = CLKPWR_GetPCLK (CLKPWR_PCLKSEL_I2C0) / target_clock; + } + else if (I2Cx == LPC_I2C1) + { + temp = CLKPWR_GetPCLK (CLKPWR_PCLKSEL_I2C1) / target_clock; + } + else if (I2Cx == LPC_I2C2) + { + temp = CLKPWR_GetPCLK (CLKPWR_PCLKSEL_I2C2) / target_clock; + } + + /* Set the I2C clock value to register */ + I2Cx->I2SCLH = (uint32_t)(temp / 2); + I2Cx->I2SCLL = (uint32_t)(temp - I2Cx->I2SCLH); +} +/* End of Private Functions --------------------------------------------------- */ + + +/* Public Functions ----------------------------------------------------------- */ +/** @addtogroup I2C_Public_Functions + * @{ + */ + +/********************************************************************//** + * @brief Initializes the I2Cx peripheral with specified parameter. + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] clockrate Target clock rate value to initialized I2C + * peripheral (Hz) + * @return None + *********************************************************************/ +void I2C_Init(LPC_I2C_TypeDef *I2Cx, uint32_t clockrate) +{ + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + + if (I2Cx==LPC_I2C0) + { + /* Set up clock and power for I2C0 module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCI2C0, ENABLE); + /* As default, peripheral clock for I2C0 module + * is set to FCCLK / 2 */ + CLKPWR_SetPCLKDiv(CLKPWR_PCLKSEL_I2C0, CLKPWR_PCLKSEL_CCLK_DIV_2); + } + else if (I2Cx==LPC_I2C1) + { + /* Set up clock and power for I2C1 module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCI2C1, ENABLE); + /* As default, peripheral clock for I2C1 module + * is set to FCCLK / 2 */ + CLKPWR_SetPCLKDiv(CLKPWR_PCLKSEL_I2C1, CLKPWR_PCLKSEL_CCLK_DIV_2); + } + else if (I2Cx==LPC_I2C2) + { + /* Set up clock and power for I2C2 module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCI2C2, ENABLE); + /* As default, peripheral clock for I2C2 module + * is set to FCCLK / 2 */ + CLKPWR_SetPCLKDiv(CLKPWR_PCLKSEL_I2C2, CLKPWR_PCLKSEL_CCLK_DIV_2); + } + else { + // Up-Support this device + return; + } + + /* Set clock rate */ + I2C_SetClock(I2Cx, clockrate); + /* Set I2C operation to default */ + I2Cx->I2CONCLR = (I2C_I2CONCLR_AAC | I2C_I2CONCLR_STAC | I2C_I2CONCLR_I2ENC); +} + +/*********************************************************************//** + * @brief De-initializes the I2C peripheral registers to their + * default reset values. + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return None + **********************************************************************/ +void I2C_DeInit(LPC_I2C_TypeDef* I2Cx) +{ + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + + /* Disable I2C control */ + I2Cx->I2CONCLR = I2C_I2CONCLR_I2ENC; + + if (I2Cx==LPC_I2C0) + { + /* Disable power for I2C0 module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCI2C0, DISABLE); + } + else if (I2Cx==LPC_I2C1) + { + /* Disable power for I2C1 module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCI2C1, DISABLE); + } + else if (I2Cx==LPC_I2C2) + { + /* Disable power for I2C2 module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCI2C2, DISABLE); + } +} + +/*********************************************************************//** + * @brief Enable or disable I2C peripheral's operation + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] NewState New State of I2Cx peripheral's operation + * @return none + **********************************************************************/ +void I2C_Cmd(LPC_I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + + if (NewState == ENABLE) + { + I2Cx->I2CONSET = I2C_I2CONSET_I2EN; + } + else + { + I2Cx->I2CONCLR = I2C_I2CONCLR_I2ENC; + } +} + +/*********************************************************************//** + * @brief Enable/Disable interrupt for I2C peripheral + * @param[in] I2Cx I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] NewState New State of I2C peripheral interrupt in NVIC core + * should be: + * - ENABLE: enable interrupt for this I2C peripheral + * - DISABLE: disable interrupt for this I2C peripheral + * @return None + **********************************************************************/ +void I2C_IntCmd (LPC_I2C_TypeDef *I2Cx, Bool NewState) +{ + if (NewState) + { + if(I2Cx == LPC_I2C0) + { + NVIC_EnableIRQ(I2C0_IRQn); + } + else if (I2Cx == LPC_I2C1) + { + NVIC_EnableIRQ(I2C1_IRQn); + } + else if (I2Cx == LPC_I2C2) + { + NVIC_EnableIRQ(I2C2_IRQn); + } + } + else + { + if(I2Cx == LPC_I2C0) + { + NVIC_DisableIRQ(I2C0_IRQn); + } + else if (I2Cx == LPC_I2C1) + { + NVIC_DisableIRQ(I2C1_IRQn); + } + else if (I2Cx == LPC_I2C2) + { + NVIC_DisableIRQ(I2C2_IRQn); + } + } + return; +} + + +/*********************************************************************//** + * @brief General Master Interrupt handler for I2C peripheral + * @param[in] I2Cx I2C peripheral selected, should be: + * - LPC_I2C + * - LPC_I2C1 + * - LPC_I2C2 + * @return None + **********************************************************************/ +void I2C_MasterHandler (LPC_I2C_TypeDef *I2Cx) +{ + int32_t tmp; + uint8_t returnCode; + I2C_M_SETUP_Type *txrx_setup; + + tmp = I2C_getNum(I2Cx); + txrx_setup = (I2C_M_SETUP_Type *) i2cdat[tmp].txrx_setup; + + returnCode = (I2Cx->I2STAT & I2C_STAT_CODE_BITMASK); + // Save current status + txrx_setup->status = returnCode; + // there's no relevant information + if (returnCode == I2C_I2STAT_NO_INF){ + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + return; + } + + /* ----------------------------- TRANSMIT PHASE --------------------------*/ + if (i2cdat[tmp].dir == 0){ + switch (returnCode) + { + /* A start/repeat start condition has been transmitted -------------------*/ + case I2C_I2STAT_M_TX_START: + case I2C_I2STAT_M_TX_RESTART: + I2Cx->I2CONCLR = I2C_I2CONCLR_STAC; + /* + * If there's any transmit data, then start to + * send SLA+W right now, otherwise check whether if there's + * any receive data for next state. + */ + if ((txrx_setup->tx_data != NULL) && (txrx_setup->tx_length != 0)){ + I2Cx->I2DAT = (txrx_setup->sl_addr7bit << 1); + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + } else { + goto next_stage; + } + break; + + /* SLA+W has been transmitted, ACK has been received ----------------------*/ + case I2C_I2STAT_M_TX_SLAW_ACK: + /* Data has been transmitted, ACK has been received */ + case I2C_I2STAT_M_TX_DAT_ACK: + /* Send more data */ + if ((txrx_setup->tx_count < txrx_setup->tx_length) \ + && (txrx_setup->tx_data != NULL)){ + I2Cx->I2DAT = *(uint8_t *)(txrx_setup->tx_data + txrx_setup->tx_count); + txrx_setup->tx_count++; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + } + // no more data, switch to next stage + else { +next_stage: + // change direction + i2cdat[tmp].dir = 1; + // Check if any data to receive + if ((txrx_setup->rx_length != 0) && (txrx_setup->rx_data != NULL)){ + // check whether if we need to issue an repeat start + if ((txrx_setup->tx_length != 0) && (txrx_setup->tx_data != NULL)){ + // Send out an repeat start command + I2Cx->I2CONSET = I2C_I2CONSET_STA; + I2Cx->I2CONCLR = I2C_I2CONCLR_AAC | I2C_I2CONCLR_SIC; + } + // Don't need issue an repeat start, just goto send SLA+R + else { + goto send_slar; + } + } + // no more data send, the go to end stage now + else { + // success, goto end stage + txrx_setup->status |= I2C_SETUP_STATUS_DONE; + goto end_stage; + } + } + break; + + /* SLA+W has been transmitted, NACK has been received ----------------------*/ + case I2C_I2STAT_M_TX_SLAW_NACK: + /* Data has been transmitted, NACK has been received -----------------------*/ + case I2C_I2STAT_M_TX_DAT_NACK: + // update status + txrx_setup->status |= I2C_SETUP_STATUS_NOACKF; + goto retry; + /* Arbitration lost in SLA+R/W or Data bytes -------------------------------*/ + case I2C_I2STAT_M_TX_ARB_LOST: + // update status + txrx_setup->status |= I2C_SETUP_STATUS_ARBF; + default: + goto retry; + } + } + + /* ----------------------------- RECEIVE PHASE --------------------------*/ + else if (i2cdat[tmp].dir == 1){ + switch (returnCode){ + /* A start/repeat start condition has been transmitted ---------------------*/ + case I2C_I2STAT_M_RX_START: + case I2C_I2STAT_M_RX_RESTART: + I2Cx->I2CONCLR = I2C_I2CONCLR_STAC; + /* + * If there's any receive data, then start to + * send SLA+R right now, otherwise check whether if there's + * any receive data for end of state. + */ + if ((txrx_setup->rx_data != NULL) && (txrx_setup->rx_length != 0)){ +send_slar: + I2Cx->I2DAT = (txrx_setup->sl_addr7bit << 1) | 0x01; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + } else { + // Success, goto end stage + txrx_setup->status |= I2C_SETUP_STATUS_DONE; + goto end_stage; + } + break; + + /* SLA+R has been transmitted, ACK has been received -----------------*/ + case I2C_I2STAT_M_RX_SLAR_ACK: + if (txrx_setup->rx_count < (txrx_setup->rx_length - 1)) { + /*Data will be received, ACK will be return*/ + I2Cx->I2CONSET = I2C_I2CONSET_AA; + } + else { + /*Last data will be received, NACK will be return*/ + I2Cx->I2CONCLR = I2C_I2CONSET_AA; + } + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Data has been received, ACK has been returned ----------------------*/ + case I2C_I2STAT_M_RX_DAT_ACK: + // Note save data and increase counter first, then check later + /* Save data */ + if ((txrx_setup->rx_data != NULL) && (txrx_setup->rx_count < txrx_setup->rx_length)){ + *(uint8_t *)(txrx_setup->rx_data + txrx_setup->rx_count) = (I2Cx->I2DAT & I2C_I2DAT_BITMASK); + txrx_setup->rx_count++; + } + if (txrx_setup->rx_count < (txrx_setup->rx_length - 1)) { + /*Data will be received, ACK will be return*/ + I2Cx->I2CONSET = I2C_I2CONSET_AA; + } + else { + /*Last data will be received, NACK will be return*/ + I2Cx->I2CONCLR = I2C_I2CONSET_AA; + } + + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Data has been received, NACK has been return -------------------------*/ + case I2C_I2STAT_M_RX_DAT_NACK: + /* Save the last data */ + if ((txrx_setup->rx_data != NULL) && (txrx_setup->rx_count < txrx_setup->rx_length)){ + *(uint8_t *)(txrx_setup->rx_data + txrx_setup->rx_count) = (I2Cx->I2DAT & I2C_I2DAT_BITMASK); + txrx_setup->rx_count++; + } + // success, go to end stage + txrx_setup->status |= I2C_SETUP_STATUS_DONE; + goto end_stage; + + /* SLA+R has been transmitted, NACK has been received ------------------*/ + case I2C_I2STAT_M_RX_SLAR_NACK: + // update status + txrx_setup->status |= I2C_SETUP_STATUS_NOACKF; + goto retry; + + /* Arbitration lost ----------------------------------------------------*/ + case I2C_I2STAT_M_RX_ARB_LOST: + // update status + txrx_setup->status |= I2C_SETUP_STATUS_ARBF; + default: +retry: + // check if retransmission is available + if (txrx_setup->retransmissions_count < txrx_setup->retransmissions_max){ + // Clear tx count + txrx_setup->tx_count = 0; + I2Cx->I2CONSET = I2C_I2CONSET_STA; + I2Cx->I2CONCLR = I2C_I2CONCLR_AAC | I2C_I2CONCLR_SIC; + txrx_setup->retransmissions_count++; + } + // End of stage + else { +end_stage: + // Disable interrupt + I2C_IntCmd(I2Cx, FALSE); + // Send stop + I2C_Stop(I2Cx); + + I2C_MasterComplete[tmp] = TRUE; + } + break; + } + } +} + + +/*********************************************************************//** + * @brief General Slave Interrupt handler for I2C peripheral + * @param[in] I2Cx I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return None + **********************************************************************/ +void I2C_SlaveHandler (LPC_I2C_TypeDef *I2Cx) +{ + int32_t tmp; + uint8_t returnCode; + I2C_S_SETUP_Type *txrx_setup; + uint32_t timeout; + + tmp = I2C_getNum(I2Cx); + txrx_setup = (I2C_S_SETUP_Type *) i2cdat[tmp].txrx_setup; + + returnCode = (I2Cx->I2STAT & I2C_STAT_CODE_BITMASK); + // Save current status + txrx_setup->status = returnCode; + // there's no relevant information + if (returnCode == I2C_I2STAT_NO_INF){ + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + return; + } + + + switch (returnCode) + { + + /* No status information */ + case I2C_I2STAT_NO_INF: + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Reading phase -------------------------------------------------------- */ + /* Own SLA+R has been received, ACK has been returned */ + case I2C_I2STAT_S_RX_SLAW_ACK: + /* General call address has been received, ACK has been returned */ + case I2C_I2STAT_S_RX_GENCALL_ACK: + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Previously addressed with own SLA; + * DATA byte has been received; + * ACK has been returned */ + case I2C_I2STAT_S_RX_PRE_SLA_DAT_ACK: + /* DATA has been received, ACK hasn been return */ + case I2C_I2STAT_S_RX_PRE_GENCALL_DAT_ACK: + /* + * All data bytes that over-flow the specified receive + * data length, just ignore them. + */ + if ((txrx_setup->rx_count < txrx_setup->rx_length) \ + && (txrx_setup->rx_data != NULL)){ + *(uint8_t *)(txrx_setup->rx_data + txrx_setup->rx_count) = (uint8_t)I2Cx->I2DAT; + txrx_setup->rx_count++; + } + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Previously addressed with own SLA; + * DATA byte has been received; + * NOT ACK has been returned */ + case I2C_I2STAT_S_RX_PRE_SLA_DAT_NACK: + /* DATA has been received, NOT ACK has been returned */ + case I2C_I2STAT_S_RX_PRE_GENCALL_DAT_NACK: + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* + * Note that: Return code only let us know a stop condition mixed + * with a repeat start condition in the same code value. + * So we should provide a time-out. In case this is really a stop + * condition, this will return back after time out condition. Otherwise, + * next session that is slave receive data will be completed. + */ + + /* A Stop or a repeat start condition */ + case I2C_I2STAT_S_RX_STA_STO_SLVREC_SLVTRX: + // Temporally lock the interrupt for timeout condition + I2C_IntCmd(I2Cx, FALSE); + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + // enable time out + timeout = I2C_SLAVE_TIME_OUT; + while(1){ + if (I2Cx->I2CONSET & I2C_I2CONSET_SI){ + // re-Enable interrupt + I2C_IntCmd(I2Cx, TRUE); + break; + } else { + timeout--; + if (timeout == 0){ + // timeout occur, it's really a stop condition + txrx_setup->status |= I2C_SETUP_STATUS_DONE; + goto s_int_end; + } + } + } + break; + + /* Writing phase -------------------------------------------------------- */ + /* Own SLA+R has been received, ACK has been returned */ + case I2C_I2STAT_S_TX_SLAR_ACK: + /* Data has been transmitted, ACK has been received */ + case I2C_I2STAT_S_TX_DAT_ACK: + /* + * All data bytes that over-flow the specified receive + * data length, just ignore them. + */ + if ((txrx_setup->tx_count < txrx_setup->tx_length) \ + && (txrx_setup->tx_data != NULL)){ + I2Cx->I2DAT = *(uint8_t *) (txrx_setup->tx_data + txrx_setup->tx_count); + txrx_setup->tx_count++; + } + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Data has been transmitted, NACK has been received, + * that means there's no more data to send, exit now */ + /* + * Note: Don't wait for stop event since in slave transmit mode, + * since there no proof lets us know when a stop signal has been received + * on slave side. + */ + case I2C_I2STAT_S_TX_DAT_NACK: + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + txrx_setup->status |= I2C_SETUP_STATUS_DONE; + goto s_int_end; + + // Other status must be captured + default: +s_int_end: + // Disable interrupt + I2C_IntCmd(I2Cx, FALSE); + I2Cx->I2CONCLR = I2C_I2CONCLR_AAC | I2C_I2CONCLR_SIC | I2C_I2CONCLR_STAC; + I2C_SlaveComplete[tmp] = TRUE; + break; + } +} + +/*********************************************************************//** + * @brief Transmit and Receive data in master mode + * @param[in] I2Cx I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] TransferCfg Pointer to a I2C_M_SETUP_Type structure that + * contains specified information about the + * configuration for master transfer. + * @param[in] Opt a I2C_TRANSFER_OPT_Type type that selected for + * interrupt or polling mode. + * @return SUCCESS or ERROR + * + * Note: + * - In case of using I2C to transmit data only, either transmit length set to 0 + * or transmit data pointer set to NULL. + * - In case of using I2C to receive data only, either receive length set to 0 + * or receive data pointer set to NULL. + * - In case of using I2C to transmit followed by receive data, transmit length, + * transmit data pointer, receive length and receive data pointer should be set + * corresponding. + **********************************************************************/ +Status I2C_MasterTransferData(LPC_I2C_TypeDef *I2Cx, I2C_M_SETUP_Type *TransferCfg, \ + I2C_TRANSFER_OPT_Type Opt) +{ + uint8_t *txdat; + uint8_t *rxdat; + uint32_t CodeStatus; + uint8_t tmp; + + // reset all default state + txdat = (uint8_t *) TransferCfg->tx_data; + rxdat = (uint8_t *) TransferCfg->rx_data; + // Reset I2C setup value to default state + TransferCfg->tx_count = 0; + TransferCfg->rx_count = 0; + TransferCfg->status = 0; + + if (Opt == I2C_TRANSFER_POLLING){ + + /* First Start condition -------------------------------------------------------------- */ + TransferCfg->retransmissions_count = 0; +retry: + // reset all default state + txdat = (uint8_t *) TransferCfg->tx_data; + rxdat = (uint8_t *) TransferCfg->rx_data; + // Reset I2C setup value to default state + TransferCfg->tx_count = 0; + TransferCfg->rx_count = 0; + CodeStatus = 0; + + // Start command + CodeStatus = I2C_Start(I2Cx); + if ((CodeStatus != I2C_I2STAT_M_TX_START) \ + && (CodeStatus != I2C_I2STAT_M_TX_RESTART)){ + TransferCfg->retransmissions_count++; + if (TransferCfg->retransmissions_count > TransferCfg->retransmissions_max){ + // save status + TransferCfg->status = CodeStatus; + goto error; + } else { + goto retry; + } + } + + /* In case of sending data first --------------------------------------------------- */ + if ((TransferCfg->tx_length != 0) && (TransferCfg->tx_data != NULL)){ + + /* Send slave address + WR direction bit = 0 ----------------------------------- */ + CodeStatus = I2C_SendByte(I2Cx, (TransferCfg->sl_addr7bit << 1)); + if (CodeStatus != I2C_I2STAT_M_TX_SLAW_ACK){ + TransferCfg->retransmissions_count++; + if (TransferCfg->retransmissions_count > TransferCfg->retransmissions_max){ + // save status + TransferCfg->status = CodeStatus | I2C_SETUP_STATUS_NOACKF; + goto error; + } else { + goto retry; + } + } + + /* Send a number of data bytes ---------------------------------------- */ + while (TransferCfg->tx_count < TransferCfg->tx_length) + { + CodeStatus = I2C_SendByte(I2Cx, *txdat); + if (CodeStatus != I2C_I2STAT_M_TX_DAT_ACK){ + TransferCfg->retransmissions_count++; + if (TransferCfg->retransmissions_count > TransferCfg->retransmissions_max){ + // save status + TransferCfg->status = CodeStatus | I2C_SETUP_STATUS_NOACKF; + goto error; + } else { + goto retry; + } + } + + txdat++; + TransferCfg->tx_count++; + } + } + + /* Second Start condition (Repeat Start) ------------------------------------------- */ + if ((TransferCfg->tx_length != 0) && (TransferCfg->tx_data != NULL) \ + && (TransferCfg->rx_length != 0) && (TransferCfg->rx_data != NULL)){ + + CodeStatus = I2C_Start(I2Cx); + if ((CodeStatus != I2C_I2STAT_M_RX_START) \ + && (CodeStatus != I2C_I2STAT_M_RX_RESTART)){ + TransferCfg->retransmissions_count++; + if (TransferCfg->retransmissions_count > TransferCfg->retransmissions_max){ + // Update status + TransferCfg->status = CodeStatus; + goto error; + } else { + goto retry; + } + } + } + + /* Then, start reading after sending data -------------------------------------- */ + if ((TransferCfg->rx_length != 0) && (TransferCfg->rx_data != NULL)){ + /* Send slave address + RD direction bit = 1 ----------------------------------- */ + + CodeStatus = I2C_SendByte(I2Cx, ((TransferCfg->sl_addr7bit << 1) | 0x01)); + if (CodeStatus != I2C_I2STAT_M_RX_SLAR_ACK){ + TransferCfg->retransmissions_count++; + if (TransferCfg->retransmissions_count > TransferCfg->retransmissions_max){ + // update status + TransferCfg->status = CodeStatus | I2C_SETUP_STATUS_NOACKF; + goto error; + } else { + goto retry; + } + } + + /* Receive a number of data bytes ------------------------------------------------- */ + while (TransferCfg->rx_count < TransferCfg->rx_length){ + + /* + * Note that: if data length is only one, the master should not + * issue an ACK signal on bus after reading to avoid of next data frame + * on slave side + */ + if (TransferCfg->rx_count < (TransferCfg->rx_length - 1)){ + // Issue an ACK signal for next data frame + CodeStatus = I2C_GetByte(I2Cx, &tmp, TRUE); + if (CodeStatus != I2C_I2STAT_M_RX_DAT_ACK){ + TransferCfg->retransmissions_count++; + if (TransferCfg->retransmissions_count > TransferCfg->retransmissions_max){ + // update status + TransferCfg->status = CodeStatus; + goto error; + } else { + goto retry; + } + } + } else { + // Do not issue an ACK signal + CodeStatus = I2C_GetByte(I2Cx, &tmp, FALSE); + if (CodeStatus != I2C_I2STAT_M_RX_DAT_NACK){ + TransferCfg->retransmissions_count++; + if (TransferCfg->retransmissions_count > TransferCfg->retransmissions_max){ + // update status + TransferCfg->status = CodeStatus; + goto error; + } else { + goto retry; + } + } + } + *rxdat++ = tmp; + TransferCfg->rx_count++; + } + } + + /* Send STOP condition ------------------------------------------------- */ + I2C_Stop(I2Cx); + return SUCCESS; + +error: + // Send stop condition + I2C_Stop(I2Cx); + return ERROR; + } + + else if (Opt == I2C_TRANSFER_INTERRUPT){ + // Setup tx_rx data, callback and interrupt handler + tmp = I2C_getNum(I2Cx); + i2cdat[tmp].txrx_setup = (uint32_t) TransferCfg; + // Set direction phase, write first + i2cdat[tmp].dir = 0; + + /* First Start condition -------------------------------------------------------------- */ + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + I2Cx->I2CONSET = I2C_I2CONSET_STA; + I2C_IntCmd(I2Cx, TRUE); + + return (SUCCESS); + } + + return ERROR; +} + +/*********************************************************************//** + * @brief Receive and Transmit data in slave mode + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] TransferCfg Pointer to a I2C_S_SETUP_Type structure that + * contains specified information about the + * configuration for master transfer. + * @param[in] Opt I2C_TRANSFER_OPT_Type type that selected for + * interrupt or polling mode. + * @return SUCCESS or ERROR + * + * Note: + * The mode of slave's operation depends on the command sent from master on + * the I2C bus. If the master send a SLA+W command, this sub-routine will + * use receive data length and receive data pointer. If the master send a SLA+R + * command, this sub-routine will use transmit data length and transmit data + * pointer. + * If the master issue an repeat start command or a stop command, the slave will + * enable an time out condition, during time out condition, if there's no activity + * on I2C bus, the slave will exit, otherwise (i.e. the master send a SLA+R/W), + * the slave then switch to relevant operation mode. The time out should be used + * because the return status code can not show difference from stop and repeat + * start command in slave operation. + * In case of the expected data length from master is greater than data length + * that slave can support: + * - In case of reading operation (from master): slave will return I2C_I2DAT_IDLE_CHAR + * value. + * - In case of writing operation (from master): slave will ignore remain data from master. + **********************************************************************/ +Status I2C_SlaveTransferData(LPC_I2C_TypeDef *I2Cx, I2C_S_SETUP_Type *TransferCfg, \ + I2C_TRANSFER_OPT_Type Opt) +{ + uint8_t *txdat; + uint8_t *rxdat; + uint32_t CodeStatus = 0; + uint32_t timeout; + int32_t time_en; + int32_t tmp; + + // reset all default state + txdat = (uint8_t *) TransferCfg->tx_data; + rxdat = (uint8_t *) TransferCfg->rx_data; + // Reset I2C setup value to default state + TransferCfg->tx_count = 0; + TransferCfg->rx_count = 0; + TransferCfg->status = 0; + + + // Polling option + if (Opt == I2C_TRANSFER_POLLING){ + + /* Set AA bit to ACK command on I2C bus */ + I2Cx->I2CONSET = I2C_I2CONSET_AA; + /* Clear SI bit to be ready ... */ + I2Cx->I2CONCLR = (I2C_I2CONCLR_SIC | I2C_I2CONCLR_STAC); + + time_en = 0; + timeout = 0; + + while (1) + { + /* Check SI flag ready */ + if (I2Cx->I2CONSET & I2C_I2CONSET_SI) + { + time_en = 0; + + switch (CodeStatus = (I2Cx->I2STAT & I2C_STAT_CODE_BITMASK)) + { + + /* No status information */ + case I2C_I2STAT_NO_INF: + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Reading phase -------------------------------------------------------- */ + /* Own SLA+R has been received, ACK has been returned */ + case I2C_I2STAT_S_RX_SLAW_ACK: + /* General call address has been received, ACK has been returned */ + case I2C_I2STAT_S_RX_GENCALL_ACK: + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Previously addressed with own SLA; + * DATA byte has been received; + * ACK has been returned */ + case I2C_I2STAT_S_RX_PRE_SLA_DAT_ACK: + /* DATA has been received, ACK hasn been return */ + case I2C_I2STAT_S_RX_PRE_GENCALL_DAT_ACK: + /* + * All data bytes that over-flow the specified receive + * data length, just ignore them. + */ + if ((TransferCfg->rx_count < TransferCfg->rx_length) \ + && (TransferCfg->rx_data != NULL)){ + *rxdat++ = (uint8_t)I2Cx->I2DAT; + TransferCfg->rx_count++; + } + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Previously addressed with own SLA; + * DATA byte has been received; + * NOT ACK has been returned */ + case I2C_I2STAT_S_RX_PRE_SLA_DAT_NACK: + /* DATA has been received, NOT ACK has been returned */ + case I2C_I2STAT_S_RX_PRE_GENCALL_DAT_NACK: + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* + * Note that: Return code only let us know a stop condition mixed + * with a repeat start condition in the same code value. + * So we should provide a time-out. In case this is really a stop + * condition, this will return back after time out condition. Otherwise, + * next session that is slave receive data will be completed. + */ + + /* A Stop or a repeat start condition */ + case I2C_I2STAT_S_RX_STA_STO_SLVREC_SLVTRX: + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + // enable time out + time_en = 1; + timeout = 0; + break; + + /* Writing phase -------------------------------------------------------- */ + /* Own SLA+R has been received, ACK has been returned */ + case I2C_I2STAT_S_TX_SLAR_ACK: + /* Data has been transmitted, ACK has been received */ + case I2C_I2STAT_S_TX_DAT_ACK: + /* + * All data bytes that over-flow the specified receive + * data length, just ignore them. + */ + if ((TransferCfg->tx_count < TransferCfg->tx_length) \ + && (TransferCfg->tx_data != NULL)){ + I2Cx->I2DAT = *txdat++; + TransferCfg->tx_count++; + } + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + break; + + /* Data has been transmitted, NACK has been received, + * that means there's no more data to send, exit now */ + /* + * Note: Don't wait for stop event since in slave transmit mode, + * since there no proof lets us know when a stop signal has been received + * on slave side. + */ + case I2C_I2STAT_S_TX_DAT_NACK: + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + // enable time out + time_en = 1; + timeout = 0; + break; + + // Other status must be captured + default: + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + goto s_error; + } + } else if (time_en){ + if (timeout++ > I2C_SLAVE_TIME_OUT){ + // it's really a stop condition, goto end stage + goto s_end_stage; + } + } + } + +s_end_stage: + /* Clear AA bit to disable ACK on I2C bus */ + I2Cx->I2CONCLR = I2C_I2CONCLR_AAC; + // Check if there's no error during operation + // Update status + TransferCfg->status = CodeStatus | I2C_SETUP_STATUS_DONE; + return SUCCESS; + +s_error: + /* Clear AA bit to disable ACK on I2C bus */ + I2Cx->I2CONCLR = I2C_I2CONCLR_AAC; + // Update status + TransferCfg->status = CodeStatus; + return ERROR; + } + + else if (Opt == I2C_TRANSFER_INTERRUPT){ + // Setup tx_rx data, callback and interrupt handler + tmp = I2C_getNum(I2Cx); + i2cdat[tmp].txrx_setup = (uint32_t) TransferCfg; + // Set direction phase, read first + i2cdat[tmp].dir = 1; + + // Enable AA + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC | I2C_I2CONCLR_STAC; + I2C_IntCmd(I2Cx, TRUE); + + return (SUCCESS); + } + + return ERROR; +} + +/*********************************************************************//** + * @brief Set Own slave address in I2C peripheral corresponding to + * parameter specified in OwnSlaveAddrConfigStruct. + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] OwnSlaveAddrConfigStruct Pointer to a I2C_OWNSLAVEADDR_CFG_Type + * structure that contains the configuration information for the +* specified I2C slave address. + * @return None + **********************************************************************/ +void I2C_SetOwnSlaveAddr(LPC_I2C_TypeDef *I2Cx, I2C_OWNSLAVEADDR_CFG_Type *OwnSlaveAddrConfigStruct) +{ + uint32_t tmp; + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + CHECK_PARAM(PARAM_I2C_SLAVEADDR_CH(OwnSlaveAddrConfigStruct->SlaveAddrChannel)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(OwnSlaveAddrConfigStruct->GeneralCallState)); + + tmp = (((uint32_t)(OwnSlaveAddrConfigStruct->SlaveAddr_7bit << 1)) \ + | ((OwnSlaveAddrConfigStruct->GeneralCallState == ENABLE) ? 0x01 : 0x00))& I2C_I2ADR_BITMASK; + switch (OwnSlaveAddrConfigStruct->SlaveAddrChannel) + { + case 0: + I2Cx->I2ADR0 = tmp; + I2Cx->I2MASK0 = I2C_I2MASK_MASK((uint32_t) \ + (OwnSlaveAddrConfigStruct->SlaveAddrMaskValue)); + break; + case 1: + I2Cx->I2ADR1 = tmp; + I2Cx->I2MASK1 = I2C_I2MASK_MASK((uint32_t) \ + (OwnSlaveAddrConfigStruct->SlaveAddrMaskValue)); + break; + case 2: + I2Cx->I2ADR2 = tmp; + I2Cx->I2MASK2 = I2C_I2MASK_MASK((uint32_t) \ + (OwnSlaveAddrConfigStruct->SlaveAddrMaskValue)); + break; + case 3: + I2Cx->I2ADR3 = tmp; + I2Cx->I2MASK3 = I2C_I2MASK_MASK((uint32_t) \ + (OwnSlaveAddrConfigStruct->SlaveAddrMaskValue)); + break; + } +} + + +/*********************************************************************//** + * @brief Configures functionality in I2C monitor mode + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] MonitorCfgType Monitor Configuration type, should be: + * - I2C_MONITOR_CFG_SCL_OUTPUT: I2C module can 'stretch' + * the clock line (hold it low) until it has had time to + * respond to an I2C interrupt. + * - I2C_MONITOR_CFG_MATCHALL: When this bit is set to '1' + * and the I2C is in monitor mode, an interrupt will be + * generated on ANY address received. + * @param[in] NewState New State of this function, should be: + * - ENABLE: Enable this function. + * - DISABLE: Disable this function. + * @return None + **********************************************************************/ +void I2C_MonitorModeConfig(LPC_I2C_TypeDef *I2Cx, uint32_t MonitorCfgType, FunctionalState NewState) +{ + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + CHECK_PARAM(PARAM_I2C_MONITOR_CFG(MonitorCfgType)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + if (NewState == ENABLE) + { + I2Cx->MMCTRL |= MonitorCfgType; + } + else + { + I2Cx->MMCTRL &= (~MonitorCfgType) & I2C_I2MMCTRL_BITMASK; + } +} + + +/*********************************************************************//** + * @brief Enable/Disable I2C monitor mode + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @param[in] NewState New State of this function, should be: + * - ENABLE: Enable monitor mode. + * - DISABLE: Disable monitor mode. + * @return None + **********************************************************************/ +void I2C_MonitorModeCmd(LPC_I2C_TypeDef *I2Cx, FunctionalState NewState) +{ + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + if (NewState == ENABLE) + { + I2Cx->MMCTRL |= I2C_I2MMCTRL_MM_ENA; + I2Cx->I2CONSET = I2C_I2CONSET_AA; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC | I2C_I2CONCLR_STAC; + } + else + { + I2Cx->MMCTRL &= (~I2C_I2MMCTRL_MM_ENA) & I2C_I2MMCTRL_BITMASK; + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC | I2C_I2CONCLR_STAC | I2C_I2CONCLR_AAC; + } + I2C_MonitorBufferIndex = 0; +} + + +/*********************************************************************//** + * @brief Get data from I2C data buffer in monitor mode. + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return None + * Note: In monitor mode, the I2C module may lose the ability to stretch + * the clock (stall the bus) if the ENA_SCL bit is not set. This means that + * the processor will have a limited amount of time to read the contents of + * the data received on the bus. If the processor reads the I2DAT shift + * register, as it ordinarily would, it could have only one bit-time to + * respond to the interrupt before the received data is overwritten by + * new data. + **********************************************************************/ +uint8_t I2C_MonitorGetDatabuffer(LPC_I2C_TypeDef *I2Cx) +{ + CHECK_PARAM(PARAM_I2Cx(I2Cx)); + return ((uint8_t)(I2Cx->I2DATA_BUFFER)); +} + +/*********************************************************************//** + * @brief Get data from I2C data buffer in monitor mode. + * @param[in] I2Cx I2C peripheral selected, should be + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return None + * Note: In monitor mode, the I2C module may lose the ability to stretch + * the clock (stall the bus) if the ENA_SCL bit is not set. This means that + * the processor will have a limited amount of time to read the contents of + * the data received on the bus. If the processor reads the I2DAT shift + * register, as it ordinarily would, it could have only one bit-time to + * respond to the interrupt before the received data is overwritten by + * new data. + **********************************************************************/ +BOOL_8 I2C_MonitorHandler(LPC_I2C_TypeDef *I2Cx, uint8_t *buffer, uint32_t size) +{ + BOOL_8 ret=FALSE; + + I2Cx->I2CONCLR = I2C_I2CONCLR_SIC; + + buffer[I2C_MonitorBufferIndex] = (uint8_t)(I2Cx->I2DATA_BUFFER); + I2C_MonitorBufferIndex++; + if(I2C_MonitorBufferIndex >= size) + { + ret = TRUE; + } + return ret; +} +/*********************************************************************//** + * @brief Get status of Master Transfer + * @param[in] I2Cx I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return Master transfer status, could be: + * - TRUE master transfer completed + * - FALSE master transfer have not completed yet + **********************************************************************/ +uint32_t I2C_MasterTransferComplete(LPC_I2C_TypeDef *I2Cx) +{ + uint32_t retval, tmp; + tmp = I2C_getNum(I2Cx); + retval = I2C_MasterComplete[tmp]; + I2C_MasterComplete[tmp] = FALSE; + return retval; +} + +/*********************************************************************//** + * @brief Get status of Slave Transfer + * @param[in] I2Cx I2C peripheral selected, should be: + * - LPC_I2C0 + * - LPC_I2C1 + * - LPC_I2C2 + * @return Complete status, could be: TRUE/FALSE + **********************************************************************/ +uint32_t I2C_SlaveTransferComplete(LPC_I2C_TypeDef *I2Cx) +{ + uint32_t retval, tmp; + tmp = I2C_getNum(I2Cx); + retval = I2C_SlaveComplete[tmp]; + I2C_SlaveComplete[tmp] = FALSE; + return retval; +} + + + +/** + * @} + */ + +#endif /* _I2C */ + +/** + * @} + */ + +/* --------------------------------- End Of File ------------------------------ */ +#endif /* __LPC17XX__ */