Diff: SPI_MX25R.cpp

Revision:

2:f72110475fec

Parent:

1:8403da5975cb

Child:

3:b6bb8d236251

--- a/SPI_MX25R.cpp	Mon Jul 20 20:45:33 2015 +0000
+++ b/SPI_MX25R.cpp	Thu Jul 23 17:11:27 2015 +0000
@@ -1,178 +1,185 @@
 /*
- * SPI_MX25R SPI-Flash Memory
+ * SPI_MX25R Series SPI-Flash Memory
  * Macronix Low Power Serial NOR Flash
  * (x2, and x4 I/O modes not implemented)
  */
  
 #include "SPI_MX25R.h"
 
-#define CMD_READ      0x03  // x1 Normal Read Data Byte 
-#define CMD_FREAD     0x0B  // x1 Fast Read Data Byte
-#define CMD_PP        0x02  // Page Program 
-#define CMD_SE        0x20  // 4KB Sector Erase 
-#define CMD_32KBE     0x52  // 32KB Block Erase 
-#define CMD_BE        0xD8  // 64KB Block Erase 
-#define CMD_CE        0xC7  // Chip Erase 
-#define CMD_RDID      0x9F  // Read Identification 
-#define CMD_RDSFDP    0x5A  // Read SFDP 
-#define CMD_RDSR      0x05  // Read Status Register 
-#define CMD_RDCR      0x15  // Read Configuration Register 
-#define CMD_WREN      0x06  // Write Enable 
-#define CMD_WRDI      0x04  // Write Disable
-#define CMD_WRSR      0x01  // Write Status Register
-#define CMD_RSTEN     0x66  // Reset Enable 
-#define CMD_RST       0x99  // Reset 
-#define CMD_PESUS     0xB0  // x4 Program/Erase Suspend 
-#define CMD_PERES     0x30  // x4 Program/Erase Resume
-#define CMD_DP        0xB9  // Enter Deep Power Down 
-#define CMD_SBL       0xC0  // Set Burst Length 
-#define CMD_RRE       0xFF  // Release Read Enhanced Mode
-#define CMD_NOP       0x00  // No Operation
-#define CMD_ENSO      0xB1  // Enter Secure OTP
-#define CMD_EXSO      0xC1  // Exit Secure OTP
-// x2 and x4 commands not currently supported with FRDM K64F platform
-//#define CMD_2READ     0xBB  // x2 2READ 
-//#define CMD_DREAD     0x3B  // x2 DREAD 
-//#define CMD_4READ     0xEB  // x4 4READ 
-//#define CMD_QREAD     0x6B  // x4 QREAD 
-//#define CMD_4PP       0x38  // x4 PP
  
-
 SPI_MX25R::SPI_MX25R(PinName mosi, PinName miso, PinName sclk, PinName cs) :
         m_spi(mosi, miso, sclk), m_cs(cs) { }
-
+ 
 SPI_MX25R::~SPI_MX25R() { }
-
+ 
 void SPI_MX25R::writeEnable(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_WREN) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 }
-
+ 
 void SPI_MX25R::writeDisable(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_WRDI) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 }    
-
+ 
 void SPI_MX25R::resetEnable(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_RSTEN) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 }  
-
+ 
 void SPI_MX25R::reset(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_RST) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 void SPI_MX25R::pgmersSuspend(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_PESUS) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 void SPI_MX25R::pgmersResume(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_PERES) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 void SPI_MX25R::deepPowerdown(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_DP) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 void SPI_MX25R::setBurstlength(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_SBL) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 void SPI_MX25R::releaseReadenhaced(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_RRE) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 void SPI_MX25R::noOperation(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_NOP) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 void SPI_MX25R::enterSecureOTP(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_ENSO) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 }
  
 void SPI_MX25R::exitSecureOTP(void)
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_EXSO) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
 } 
-
+ 
 uint8_t SPI_MX25R::readStatus(void)
 {   
     uint8_t data ;
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_RDSR) ;
-    data = m_spi.write(CMD_RDSR) ;                  // dummy
-    m_spi.write(CMD_RDSR) ;         
-    data = m_spi.write(CMD_RDSR) ;                  // dummy
-    m_cs = 1 ;
+    data = m_spi.write(DUMMY) ;                     // dummy
+    m_cs = CS_HIGH ;
     return( data ) ;
-  }
+}
   
 uint32_t SPI_MX25R::readConfig(void)
 {   
     uint8_t data;
     uint32_t config32 = 0 ;
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_RDCR) ;                         // send 15h
-      data= m_spi.write(0x55)  ;                    // dumy to get 1st Byte out
-      config32 = config32 | data ;                  // put in 32b reg
-      data= m_spi.write(0x55) ;                     // dummy to get 2nd Byte out
-      config32 = (config32 << 8) | data ;           // shift and put in reg
-    m_cs = 1 ;
-     return( config32 ) ;  
+    data= m_spi.write(DUMMY)  ;                     // dumy to get 1st Byte out
+    config32 = config32 | data ;                    // put in 32b reg
+    data= m_spi.write(DUMMY) ;                      // dummy to get 2nd Byte out
+    config32 = (config32 << 8) | data ;             // shift and put in reg
+    m_cs = CS_HIGH ;
+    return( config32 ) ;  
+}
+
+uint8_t SPI_MX25R::readSecurity(void)
+{   
+    uint8_t data ;
+    m_cs = CS_LOW ;
+    m_spi.write(CMD_RDSCUR) ;                       // send 2Bh
+    data = m_spi.write(DUMMY) ;                     // dummy
+    m_cs = CS_HIGH ;
+    return( data ) ;
 }
   
 uint32_t SPI_MX25R::readID(void)
 {   
     uint8_t data;
-     uint32_t data32 = 0 ;
-    m_cs = 0 ;
+    uint32_t data32 = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_RDID) ;                         // send 9Fh
-      data= m_spi.write(0x55)  ;                    // dumy to get 1st Byte out
-      data32 = data32 | data ;                      // put in 32b reg
-      data= m_spi.write(CMD_RDID) ;                 // dummy to get 2nd Byte out
-      data32 = (data32 << 8) | data ;               // shift and put in reg
-      data= m_spi.write(0x55)  ;                    // dummy to get 3rd Byte out
-      data32 = (data32 << 8) | data ;               // shift again and put in reg
-    m_cs = 1 ;
-     return( data32 ) ;  
+    data= m_spi.write(DUMMY)  ;                     // dumy to get 1st Byte out
+    data32 = data32 | data ;                        // put in 32b reg
+    data= m_spi.write(DUMMY) ;                      // dummy to get 2nd Byte out
+    data32 = (data32 << 8) | data ;                 // shift and put in reg
+    data= m_spi.write(DUMMY)  ;                     // dummy to get 3rd Byte out
+    data32 = (data32 << 8) | data ;                 // shift again and put in reg
+    m_cs = CS_HIGH ;
+    return( data32 ) ;  
 }
 
+uint32_t SPI_MX25R::readREMS(void)
+{   
+    uint8_t data;
+    uint32_t data32 = 0 ;
+    m_cs = CS_LOW ;
+    m_spi.write(CMD_REMS) ;                         // send 90h
+    m_spi.write(DUMMY) ;                            // send DUMMY1
+    m_spi.write(DUMMY) ;                            // send DUMMY2
+    m_spi.write(0) ;                                // send address=0x00 to get Manu ID 1st.
+    data= m_spi.write(DUMMY)  ;                     // dumy to get Manufacturer ID= C2h out
+    data32 = data32 | data ;                        // put in 32b reg
+    data= m_spi.write(DUMMY) ;                      // dummy to get 2nd Byte = Device ID out
+    data32 = (data32 << 8) | data ;                 // shift and put in reg
+    m_cs = CS_HIGH ;
+    return( data32 ) ;  
+}
+
+uint8_t SPI_MX25R::readRES(void)
+{   
+    uint8_t data;
+    m_cs = CS_LOW ;
+    m_spi.write(CMD_RES) ;                          // send ABh
+    m_spi.write(DUMMY) ;                            // send DUMMY1
+    m_spi.write(DUMMY) ;                            // send DUMMY2
+    m_spi.write(DUMMY) ;                            // send DUMMY3
+    data= m_spi.write(DUMMY)  ;                     // dumy to get Electronic Sig. out
+    m_cs = CS_HIGH ;
+    return( data ) ;  
+}
+ 
 void SPI_MX25R::programPage(int addr, uint8_t *data, int numData)
 {
     int i ;
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_PP) ;                           // Program Page 02h
     m_spi.write((addr >> 16)&0xFF) ;                // adr 23:16
     m_spi.write((addr >>  8)&0xFF) ;                // adr 15:8
@@ -180,18 +187,26 @@
     for (i = 0 ; i < numData ; i++ ) {              // data = 00, 01, 02, .. to FEh, FFh = all 256 Bytes in 1 page. 
         m_spi.write(data[i]) ;
     }
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
     // poll in main
 }
-
+ 
 void SPI_MX25R::writeStatusreg(int addr)            // Write SR cmd 01h + 3B data
 {   
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_WRSR) ;                         // Write SR cmd 01h
     m_spi.write((addr >> 16)&0xFF) ;                // address
     m_spi.write((addr >>  8)&0xFF) ;
     m_spi.write(addr & 0xFF) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
+}
+
+void SPI_MX25R::writeSecurityreg(int addr)          // WRSCUR cmd 2Fh + 1B data
+{   
+    m_cs = CS_LOW ;
+    m_spi.write(CMD_WRSCUR) ;                         // Write SR cmd 01h
+    m_spi.write(addr & 0xFF) ;
+    m_cs = CS_HIGH ;
 }
 
 void SPI_MX25R::blockErase(int addr)                // 64KB Block Erase
@@ -200,91 +215,91 @@
     data[0] = (addr >> 16) & 0xFF ;
     data[1] = (addr >> 8) & 0xFF ;
     data[2] = (addr & 0xFF) ;
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_BE) ;
-    for (int i = 0 ; i < 3 ; i++ ) {
+    for (int i = 0 ; i < 3 ; i++ ) {                // Address setting
         m_spi.write(data[i]) ;
     }
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
     // poll in main
 }
-
+ 
 void SPI_MX25R::blockErase32KB(int addr)            // 32KB Block Erase
 {
     uint8_t data[3] ;
     data[0] = (addr >> 16) & 0xFF ;
     data[1] = (addr >> 8) & 0xFF ;
     data[2] = (addr & 0xFF) ;
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_32KBE) ;
-    for (int i = 0 ; i < 3 ; i++ ) {
+    for (int i = 0 ; i < 3 ; i++ ) {                // Address Setting
         m_spi.write(data[i]) ;
     }
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
     // poll in main
 }
-
+ 
 void SPI_MX25R::sectorErase(int addr)               //  4KB Sector Erase
 {
     uint8_t data[3] ;
     data[0] = (addr >> 16) & 0xFF ;
     data[1] = (addr >> 8) & 0xFF ;
     data[2] = (addr & 0xFF) ;
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_SE) ;
-    for (int i = 0 ; i < 3 ; i++ ) {
+    for (int i = 0 ; i < 3 ; i++ ) {                // Address Setting
         m_spi.write(data[i]) ;
     }
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
     // poll in main
 }
-
+ 
 void SPI_MX25R::chipErase(void)                     // Chip Erase
 {
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_CE) ;
-    m_cs = 1 ;
+    m_cs = CS_HIGH ;
     // poll in main
 }
-
+ 
 uint8_t SPI_MX25R::read8(int addr)                  // Single Byte Read
 {
     uint8_t data ;    
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_READ) ;                         // send 03h
     m_spi.write((addr >> 16)&0xFF) ;
     m_spi.write((addr >>  8)&0xFF) ;
     m_spi.write(addr & 0xFF) ;
-    data = m_spi.write(addr & 0xFF) ;               // write data is dummy 
-    m_cs = 1 ;
+    data = m_spi.write(DUMMY) ;                     // write data is dummy 
+    m_cs = CS_HIGH ;
     return( data ) ;                                // return 1 byte 
 }
-
-uint8_t SPI_MX25R::readSFDP(int addr)               // Single Byte Read
+ 
+uint8_t SPI_MX25R::readSFDP(int addr)               // Read SFDP
 {
     uint8_t data ;    
-    m_cs = 0 ;
+    m_cs = CS_LOW ;
     m_spi.write(CMD_RDSFDP) ;                       // send cmd 5Ah
-       m_spi.write((addr >> 16)&0xFF) ;             // address[23:16]
+    m_spi.write((addr >> 16)&0xFF) ;                // address[23:16]
     m_spi.write((addr >>  8)&0xFF) ;                // address[15:8]
     m_spi.write(addr & 0xFF) ;                      // address[7:0]
-    m_spi.write(0x00 & 0xFF) ;                      // dummy cycle
-    data = m_spi.write(addr & 0xFF) ;               // return 1 byte 
-    m_cs = 1 ;
+    m_spi.write(DUMMY) ;                            // dummy cycle
+    data = m_spi.write(DUMMY) ;                     // return 1 byte 
+    m_cs = CS_HIGH ;
+    return( data ) ;
+}
+ 
+uint8_t SPI_MX25R::readFREAD(int addr)              // x1 Fast Read Data Byte
+{
+    uint8_t data ;    
+    m_cs = CS_LOW ;
+    m_spi.write(CMD_FREAD) ;                        // send cmd 0BH
+    m_spi.write((addr >> 16)&0xFF) ;                // address[23:16]
+    m_spi.write((addr >>  8)&0xFF) ;                // address[15:8]
+    m_spi.write(addr & 0xFF) ;                      // address[7:0]
+    m_spi.write(DUMMY) ;                            // dummy cycle
+    data = m_spi.write(DUMMY) ;                     // return 1 byte 
+    m_cs = CS_HIGH ;
     return( data ) ;
 }
 
-uint8_t SPI_MX25R::readFREAD(int addr)              // Single Byte Read
-{
-    uint8_t data ;    
-    m_cs = 0 ;
-    m_spi.write(CMD_FREAD) ;                        // send cmd 0Bh
-       m_spi.write((addr >> 16)&0xFF) ;             // address[23:16]
-    m_spi.write((addr >>  8)&0xFF) ;                // address[15:8]
-    m_spi.write(addr & 0xFF) ;                      // address[7:0]
-    m_spi.write(0x00 & 0xFF) ;                      // dummy cycle
-    data = m_spi.write(addr & 0xFF) ;               // return 1 byte 
-    m_cs = 1 ;
-    return( data ) ;
-}
-