File content as of revision 7:3a4df8dbbb2e:

#include "mbed.h"
#include "mDot.h"
#include "MTSLog.h"
#include <string>
#include <vector>
#include <algorithm>
#include "DHT.h"
#include "LinearTemp.h"
 
DHT sensor(PB_1, DHT11);
LinearTemp  myPHSensor(PB_0, 0.005, -273.15);

// these options must match the settings on your Conduit
// uncomment the following lines and edit their values to match your configuration
static std::string config_network_name = "chinaiot";
static std::string config_network_pass = "password";
static uint8_t config_frequency_sub_band = 2;

int main() {
    int32_t ret;
    mDot* dot;
    std::vector<uint8_t> data;
    std::vector<uint8_t> send_data;
    char * PhStrBuf;
    float PhValue;
    std::string data_str = "T&H Sensors";
    int error = 0;
//    float h = 0.0f, c = 0.0f, f = 0.0f, k = 0.0f, dp = 0.0f, dpf = 0.0f;
    float h = 0.0f, c = 0.0f;
 
 
    // get a mDot handle
    dot = mDot::getInstance();


    // print library version information
    logInfo("version: %s", dot->getId().c_str());

    //*******************************************
    // configuration
    //*******************************************
    // reset to default config so we know what state we're in
    dot->resetConfig();

    dot->setLogLevel(mts::MTSLog::INFO_LEVEL);

    // set up the mDot with our network information: frequency sub band, network name, and network password
    // these can all be saved in NVM so they don't need to be set every time - see mDot::saveConfig()

    // frequency sub band is only applicable in the 915 (US) frequency band
    // if using a MultiTech Conduit gateway, use the same sub band as your Conduit (1-8) - the mDot will use the 8 channels in that sub band
    // if using a gateway that supports all 64 channels, use sub band 0 - the mDot will use all 64 channels
    logInfo("setting frequency sub band");
    if ((ret = dot->setFrequencySubBand(config_frequency_sub_band)) != mDot::MDOT_OK) {
        logError("failed to set frequency sub band %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
    }

    logInfo("setting network name");
    if ((ret = dot->setNetworkName(config_network_name)) != mDot::MDOT_OK) {
        logError("failed to set network name %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
    }

    logInfo("setting network password");
    if ((ret = dot->setNetworkPassphrase(config_network_pass)) != mDot::MDOT_OK) {
        logError("failed to set network password %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
    }

    // a higher spreading factor allows for longer range but lower throughput
    // in the 915 (US) frequency band, spreading factors 7 - 10 are available
    // in the 868 (EU) frequency band, spreading factors 7 - 12 are available
    logInfo("setting TX spreading factor");
    if ((ret = dot->setTxDataRate(mDot::SF_10)) != mDot::MDOT_OK) {
        logError("failed to set TX datarate %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
    }

    // request receive confirmation of packets from the gateway
    logInfo("enabling ACKs");
    if ((ret = dot->setAck(1)) != mDot::MDOT_OK) {
        logError("failed to enable ACKs %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
    }

    // save this configuration to the mDot's NVM
    logInfo("saving config");
    if (! dot->saveConfig()) {
        logError("failed to save configuration");
    }
    //*******************************************
    // end of configuration
    //*******************************************

    // attempt to join the network
    logInfo("joining network");
    while ((ret = dot->joinNetwork()) != mDot::MDOT_OK) {
        logError("failed to join network %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
        // in the 868 (EU) frequency band, we need to wait until another channel is available before transmitting again
        osDelay(std::max((uint32_t)1000, (uint32_t)dot->getNextTxMs()));
    }

    // format data for sending to the gateway
    for (std::string::iterator it = data_str.begin(); it != data_str.end(); it++)
        data.push_back((uint8_t) *it);

    char dataBuf[11];
    int thflag=0;
    
    while (true) {
        // send the data to the gateway
        if ((ret = dot->send(data)) != mDot::MDOT_OK) {
            logError("failed to send", ret, mDot::getReturnCodeString(ret).c_str());
        } else {
            logInfo("successfully sent data to gateway");
        }
        

        // in the 868 (EU) frequency band, we need to wait until another channel is available before transmitting again
        osDelay(std::max((uint32_t)5000, (uint32_t)dot->getNextTxMs()));

        wait(2.0f);
        error = sensor.readData();
        if (0 == error) {
            c   = sensor.ReadTemperature(CELCIUS);
//            f   = sensor.ReadTemperature(FARENHEIT);
//            k   = sensor.ReadTemperature(KELVIN);
            h   = sensor.ReadHumidity();
//            dp  = sensor.CalcdewPoint(c, h);
//            dpf = sensor.CalcdewPointFast(c, h);
            printf("Temperature: %4.2f Humidity: %4.2f\n\n", c, h);

        if (thflag==0) {
                sprintf(dataBuf, "T:%4.2f", c);
                thflag=1;
                } else {
                    sprintf(dataBuf, "H:%4.2f", h);
                    thflag=0;
                }
                    
        data.clear();
        
        // Read the PH value
        PhValue = myPHSensor;
        
        sprintf(PhStrBuf, "PH:%5.4f", PhValue);
        logInfo("PH: %5.4f", PhValue);
        
        // probably not the most efficent way to do this
        for( int i=0; i< strlen(dataBuf); i++ )
            data.push_back( dataBuf[i] );

        } else {
            printf("Error: %d\n", error);
        }

    }

//    return 0;
}