File content as of revision 144:ef7eb2e8f9f7:

/**************************************************************************/
/**
 * @file     ARMCM3.h
 * @brief    CMSIS Cortex-M3 Core Peripheral Access Layer Header File
 *           for CM3 Device Series
 * @version  V1.05
 * @date     26. July 2011
 *
 * @note
 * Copyright (C) 2010-2011 ARM Limited. All rights reserved.
 *
 * @par
 * ARM Limited (ARM) is supplying this software for use with Cortex-M
 * processor based microcontrollers.  This file can be freely distributed
 * within development tools that are supporting such ARM based processors.
 *
 * @par
 * THIS SOFTWARE IS PROVIDED "AS IS".  NO WARRANTIES, WHETHER EXPRESS, IMPLIED
 * OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
 * ARM SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
 * CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
 *
 ******************************************************************************/

#ifndef ARMCM3_H
#define ARMCM3_H

/**
 * ==========================================================================
 * ---------- Interrupt Number Definition -----------------------------------
 * ==========================================================================
 */
typedef enum IRQn
{
	/******  Cortex-M3 Processor Exceptions Numbers ***************************************************/
	NonMaskableInt_IRQn 	= -14, 		/*!<  2 Cortex-M3 Non Maskable Interrupt                  */
	HardFault_IRQn 			= -13, 		/*!<  3 Cortex-M3 Hard Fault Interrupt                    */
	MemoryManagement_IRQn 	= -12, 		/*!<  4 Cortex-M3 Memory Management Interrupt             */
	BusFault_IRQn 			= -11,		/*!<  5 Cortex-M3 Bus Fault Interrupt                     */
	UsageFault_IRQn 		= -10, 		/*!<  6 Cortex-M3 Usage Fault Interrupt                   */
	SVCall_IRQn 			= -5, 		/*!< 11 Cortex-M3 SV Call Interrupt                       */
	DebugMonitor_IRQn 		= -4, 		/*!< 12 Cortex-M3 Debug Monitor Interrupt                 */
	PendSV_IRQn 			= -2, 		/*!< 14 Cortex-M3 Pend SV Interrupt                       */
	SysTick_IRQn			= -1, 		/*!< 15 Cortex-M3 System Tick Interrupt                   */

	/******  ARMCM3 specific Interrupt Numbers ********************************************************/
	Tim0_IRQn 				= 0,
	Tim1_IRQn 				= 1,
	Tim2_IRQn 				= 2,
	Uart1_IRQn 				= 3,
	Spi_IRQn 				= 4,
	I2C_IRQn 				= 5,
	Gpio_IRQn 				= 6,
	Rtc_IRQn 				= 7,
	Flash_IRQn 				= 8,
	MacHw_IRQn 				= 9,
	Aes_IRQn 				= 10,
	Adc_IRQn 				= 11,
	ClockCal_IRQn 			= 12,
	Uart2_IRQn 				= 13,
	Uvi_IRQn				= 14,
	Dma_IRQn 				= 15,
	DbgPwrUp_IRQn 			= 16,
	Spi2_IRQn 				= 17,
	I2C2_IRQn 				= 18,
	FVDDHComp_IRQn			= 19
} IRQn_Type;

/**
 * ==========================================================================
 * ----------- Processor and Core Peripheral Section ------------------------
 * ==========================================================================
 */

/** Configuration of the Cortex-M3 Processor and Core Peripherals */
#define __CM3_REV                 0x0201    /*!< Core Revision r2p1                               */
#define __MPU_PRESENT             1         /*!< MPU present or not                               */
#define __NVIC_PRIO_BITS          4         /*!< Number of Bits used for Priority Levels          */
#define __Vendor_SysTickConfig    0         /*!< Set to 1 if different SysTick Config is used     */

//#define YOTTA_CFG_CMSIS_NVIC_USER_IRQ_OFFSET	16
//#define YOTTA_CFG_CMSIS_NVIC_USER_IRQ_NUMBER	20
//#define NVIC_NUM_VECTORS     (NVIC_USER_IRQ_OFFSET + NVIC_USER_IRQ_NUMBER)

//#define YOTTA_CFG_CMSIS_NVIC_RAM_VECTOR_ADDRESS
//#define YOTTA_CFG_CMSIS_NVIC_FLASH_VECTOR_ADDRESS	0x3000

#include <core_cm3.h>                       /* Cortex-M3 processor and core peripherals           */
#include "system_NCS36510.h"                  /* System Header                                      */

#endif  /* ARMCM3_H */