A program to monitor some parameters for a motor
Dependencies: mbed-dev BufferSerial
Thanks to David Lowe for https://developer.mbed.org/users/gregeric/code/Nucleo_Hello_Encoder/ which I adapted for the use of TIM2 32bit timer as an encoder reader on the Nucleo L432KC board.
main.cpp
- Committer:
- tonnyleonard
- Date:
- 2017-05-14
- Revision:
- 6:5d4c09973041
- Parent:
- 5:29372f6cb533
- Child:
- 7:7f59b69d8895
File content as of revision 6:5d4c09973041:
/* * Using STM32's counter peripherals to interface rotary encoders. * Encoders are supported on F4xx's TIM1,2,3,4,5. TIM2 & TIM5 have 32bit count, others 16bit. * Beware mbed uses TIM5 for system timer, SPI needs TIM1, others used for PWM. * Check your platform's PeripheralPins.c & PeripheralNames.h if you need both PWM & encoders. * * Edit HAL_TIM_Encoder_MspInitFx.cpp to suit your mcu & board's available pinouts & pullups/downs. * * Thanks to: * http://petoknm.wordpress.com/2015/01/05/rotary-encoder-and-stm32/ * * References: * http://www.st.com/st-web-ui/static/active/en/resource/technical/document/user_manual/DM00122015.pdf * http://www.st.com/st-web-ui/static/active/en/resource/technical/document/reference_manual/DM00096844.pdf * http://www.st.com/web/en/resource/technical/document/application_note/DM00042534.pdf * http://www.st.com/web/en/resource/technical/document/datasheet/DM00102166.pdf * * David Lowe Jan 2015 */ #include "mbed.h" #include "Encoder.h" #include "inttypes.h" TIM_Encoder_InitTypeDef encoder1; TIM_HandleTypeDef timer2; InterruptIn event(PA_8); DigitalOut led(LED1); AnalogIn adc1(PA_3); //ADC1_IN8 AnalogIn adc2(PA_5); //ADC1_IN10 AnalogIn adc3(PA_6); //ADC1_IN11 AnalogOut dac1(PA_4); // DAC1_OUT1 uint32_t count1=0; int16_t count2=0; int16_t count3=0; int16_t adjust=0; Timer timer1; void atint() { timer1.start(); if (__HAL_TIM_IS_TIM_COUNTING_DOWN(&timer2)) { adjust--; if (adjust == -3) { count2--; count1 +=__HAL_TIM_GET_COUNTER(&timer2); TIM2->CNT = 0x0000; adjust = 0; led =!led; } } else { adjust++; if (adjust == 3) { count2++; count1 +=__HAL_TIM_GET_COUNTER(&timer2); TIM2->CNT = 0x0000; adjust = 0; led =!led; } } } int main() { //counting on both A&B inputs (A at PA0, B at PA1), 4 ticks per cycle, //full 32-bit count //For L432KC to work with TIM2 one needs to reassign the system ticker //from TIM2 to TIM7 in TARGET/../device/hal_tick.h EncoderInit(&encoder1, &timer2, TIM2, 0xffffffff, TIM_ENCODERMODE_TI12); event.rise(&atint); printf("\n\rSTM HAL encoder with ADC and DAC\n\r"); //printf("%" PRIu32 "\n", UINT32_MAX); while(1) { uint32_t count3=0; int8_t dir1; uint16_t voltage1=0; //OK 401 411 446 NOK 030 //count1=TIM2->CNT; //dir1=TIM2->CR1&TIM_CR1_DIR; count3=__HAL_TIM_GET_COUNTER(&timer2); dir1 = __HAL_TIM_IS_TIM_COUNTING_DOWN(&timer2); voltage1=adc1.read_u16(); dac1.write_u16(count3*2); printf("%ld%s passes=%d short=%ld\r\n", count1+count3, dir1==0 ? "+":"-", count2, count3); printf("Voltage= %d, DAC=%f\r\n", voltage1, dac1.read()*3.3); printf("percentage: %3.3f%%\r\n", adc2.read()*100.0f); printf("percentage: %3.3f%%\r\n", adc3.read()*100.0f); wait(2.1); } }