File content as of revision 180:d79f997829d6:

/* mbed Microcontroller Library
 * Copyright (c) 2015-2016 Nuvoton
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#include "i2c_api.h"

#if DEVICE_I2C

#include "cmsis.h"
#include "pinmap.h"
#include "PeripheralPins.h"
#include "nu_modutil.h"
#include "nu_miscutil.h"
#include "nu_bitutil.h"
#include "mbed_critical.h"

struct nu_i2c_var {
    i2c_t *     obj;
    void        (*vec)(void);
};

static void i2c0_vec(void);
static void i2c1_vec(void);
static void i2c2_vec(void);
static void i2c_irq(i2c_t *obj);
static void i2c_fsm_reset(i2c_t *obj, uint32_t i2c_ctl);
static void i2c_fsm_tranfini(i2c_t *obj, int lastdatanaked);

static struct nu_i2c_var i2c0_var = {
    .obj                =   NULL,
    .vec                =   i2c0_vec,
};
static struct nu_i2c_var i2c1_var = {
    .obj                =   NULL,
    .vec                =   i2c1_vec,
};
static struct nu_i2c_var i2c2_var = {
    .obj                =   NULL,
    .vec                =   i2c2_vec,
};

static uint32_t i2c_modinit_mask = 0;

static const struct nu_modinit_s i2c_modinit_tab[] = {
    {I2C_0, I2C0_MODULE, 0, 0, I2C0_RST, I2C0_IRQn, &i2c0_var},
    {I2C_1, I2C1_MODULE, 0, 0, I2C1_RST, I2C1_IRQn, &i2c1_var},
    {I2C_2, I2C2_MODULE, 0, 0, I2C2_RST, I2C2_IRQn, &i2c2_var},

    {NC, 0, 0, 0, 0, (IRQn_Type) 0, NULL}
};

static int i2c_do_tran(i2c_t *obj, char *buf, int length, int read, int naklastdata);
static int i2c_do_trsn(i2c_t *obj, uint32_t i2c_ctl, int sync);
#define NU_I2C_TIMEOUT_STAT_INT     500000
#define NU_I2C_TIMEOUT_STOP         500000
static int i2c_poll_status_timeout(i2c_t *obj, int (*is_status)(i2c_t *obj), uint32_t timeout);
static int i2c_poll_tran_heatbeat_timeout(i2c_t *obj, uint32_t timeout);
static int i2c_is_trsn_done(i2c_t *obj);
static int i2c_is_tran_started(i2c_t *obj);
static int i2c_addr2data(int address, int read);
#if DEVICE_I2CSLAVE
// Convert mbed address to BSP address.
static int i2c_addr2bspaddr(int address);
#endif  // #if DEVICE_I2CSLAVE
static void i2c_enable_int(i2c_t *obj);
static void i2c_disable_int(i2c_t *obj);
static int i2c_set_int(i2c_t *obj, int inten);


#if DEVICE_I2C_ASYNCH
static void i2c_buffer_set(i2c_t *obj, const void *tx, size_t tx_length, void *rx, size_t rx_length);
static void i2c_enable_vector_interrupt(i2c_t *obj, uint32_t handler, int enable);
static void i2c_rollback_vector_interrupt(i2c_t *obj);
#endif

#define TRANCTRL_STARTED        (1)
#define TRANCTRL_NAKLASTDATA    (1 << 1)
#define TRANCTRL_LASTDATANAKED  (1 << 2)

uint32_t us_ticker_read(void);

void i2c_init(i2c_t *obj, PinName sda, PinName scl)
{
    uint32_t i2c_sda = pinmap_peripheral(sda, PinMap_I2C_SDA);
    uint32_t i2c_scl = pinmap_peripheral(scl, PinMap_I2C_SCL);
    obj->i2c.i2c = (I2CName) pinmap_merge(i2c_sda, i2c_scl);
    MBED_ASSERT((int)obj->i2c.i2c != NC);

    const struct nu_modinit_s *modinit = get_modinit(obj->i2c.i2c, i2c_modinit_tab);
    MBED_ASSERT(modinit != NULL);
    MBED_ASSERT(modinit->modname == (int) obj->i2c.i2c);

    // Reset this module
    SYS_ResetModule(modinit->rsetidx);

    // Enable IP clock
    CLK_EnableModuleClock(modinit->clkidx);

    pinmap_pinout(sda, PinMap_I2C_SDA);
    pinmap_pinout(scl, PinMap_I2C_SCL);

#if DEVICE_I2C_ASYNCH
    obj->i2c.dma_usage = DMA_USAGE_NEVER;
    obj->i2c.event = 0;
    obj->i2c.stop = 0;
    obj->i2c.address = 0;
#endif

    // NOTE: Setting I2C bus clock to 100 KHz is required. See I2C::I2C in common/I2C.cpp.
    I2C_Open((I2C_T *) NU_MODBASE(obj->i2c.i2c), 100000);
    // NOTE: INTEN bit and FSM control bits (STA, STO, SI, AA) are packed in one register CTL0. We cannot control interrupt through
    //       INTEN bit without impacting FSM control bits. Use NVIC_EnableIRQ/NVIC_DisableIRQ instead for interrupt control.
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);
    i2c_base->CTL0 |= (I2C_CTL0_INTEN_Msk | I2C_CTL0_I2CEN_Msk);

    // Enable sync-mode vector interrupt.
    struct nu_i2c_var *var = (struct nu_i2c_var *) modinit->var;
    var->obj = obj;
    obj->i2c.tran_ctrl = 0;
    obj->i2c.stop = 0;
    i2c_enable_vector_interrupt(obj, (uint32_t) var->vec, 1);

    // Mark this module to be inited.
    int i = modinit - i2c_modinit_tab;
    i2c_modinit_mask |= 1 << i;
}

int i2c_start(i2c_t *obj)
{
    return i2c_do_trsn(obj, I2C_CTL0_STA_Msk | I2C_CTL0_SI_Msk, 1);
}

int i2c_stop(i2c_t *obj)
{
    return i2c_do_trsn(obj, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk, 1);
}

void i2c_frequency(i2c_t *obj, int hz)
{
    I2C_SetBusClockFreq((I2C_T *) NU_MODBASE(obj->i2c.i2c), hz);
}

int i2c_read(i2c_t *obj, int address, char *data, int length, int stop)
{
    if (i2c_start(obj)) {
        i2c_stop(obj);
        return I2C_ERROR_BUS_BUSY;
    }

    if (i2c_byte_write(obj, i2c_addr2data(address, 1)) != 1) {
        i2c_stop(obj);
        return I2C_ERROR_NO_SLAVE;
    }

    // Read in bytes
    length = i2c_do_tran(obj, data, length, 1, 1);

    // If not repeated start, send stop.
    if (stop) {
        i2c_stop(obj);
    }

    return length;
}

int i2c_write(i2c_t *obj, int address, const char *data, int length, int stop)
{
    if (i2c_start(obj)) {
        i2c_stop(obj);
        return I2C_ERROR_BUS_BUSY;
    }

    if (i2c_byte_write(obj, i2c_addr2data(address, 0)) != 1) {
        i2c_stop(obj);
        return I2C_ERROR_NO_SLAVE;
    }

    // Write out bytes
    length = i2c_do_tran(obj, (char *) data, length, 0, 1);

    if (stop) {
        i2c_stop(obj);
    }

    return length;
}

void i2c_reset(i2c_t *obj)
{
    i2c_stop(obj);
}

int i2c_byte_read(i2c_t *obj, int last)
{
    char data = 0;
    i2c_do_tran(obj, &data, 1, 1, last);
    return data;
}

int i2c_byte_write(i2c_t *obj, int data)
{
    char data_[1];
    data_[0] = data & 0xFF;

    if (i2c_do_tran(obj, data_, 1, 0, 0) == 1 &&
            ! (obj->i2c.tran_ctrl & TRANCTRL_LASTDATANAKED)) {
        return 1;
    } else {
        return 0;
    }
}

#if DEVICE_I2CSLAVE

// See I2CSlave.h
#define NoData         0    // the slave has not been addressed
#define ReadAddressed  1    // the master has requested a read from this slave (slave = transmitter)
#define WriteGeneral   2    // the master is writing to all slave
#define WriteAddressed 3    // the master is writing to this slave (slave = receiver)

void i2c_slave_mode(i2c_t *obj, int enable_slave)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);

    i2c_disable_int(obj);

    obj->i2c.slaveaddr_state = NoData;

    // Switch to not addressed mode
    I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk);

    i2c_enable_int(obj);
}

int i2c_slave_receive(i2c_t *obj)
{
    int slaveaddr_state;

    i2c_disable_int(obj);
    slaveaddr_state = obj->i2c.slaveaddr_state;
    i2c_enable_int(obj);

    return slaveaddr_state;
}

int i2c_slave_read(i2c_t *obj, char *data, int length)
{
    return i2c_do_tran(obj, data, length, 1, 1);
}

int i2c_slave_write(i2c_t *obj, const char *data, int length)
{
    return i2c_do_tran(obj, (char *) data, length, 0, 1);
}

void i2c_slave_address(i2c_t *obj, int idx, uint32_t address, uint32_t mask)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);

    i2c_disable_int(obj);

    // NOTE: On NUC472/M451, non-zero slave address can still work as GC mode is enabled.
    //       On M480, non-zero slave address won't work as GC mode is enabled.
    I2C_SetSlaveAddr(i2c_base, 0, i2c_addr2bspaddr(address), I2C_GCMODE_DISABLE);

    i2c_enable_int(obj);
}

static int i2c_addr2bspaddr(int address)
{
    return (address >> 1);
}

#endif // #if DEVICE_I2CSLAVE

static void i2c_enable_int(i2c_t *obj)
{
    const struct nu_modinit_s *modinit = get_modinit(obj->i2c.i2c, i2c_modinit_tab);

    core_util_critical_section_enter();

    // Enable I2C interrupt
    NVIC_EnableIRQ(modinit->irq_n);
    obj->i2c.inten = 1;

    core_util_critical_section_exit();
}

static void i2c_disable_int(i2c_t *obj)
{
    const struct nu_modinit_s *modinit = get_modinit(obj->i2c.i2c, i2c_modinit_tab);

    core_util_critical_section_enter();

    // Disable I2C interrupt
    NVIC_DisableIRQ(modinit->irq_n);
    obj->i2c.inten = 0;

    core_util_critical_section_exit();
}

static int i2c_set_int(i2c_t *obj, int inten)
{
    int inten_back;

    core_util_critical_section_enter();

    inten_back = obj->i2c.inten;

    core_util_critical_section_exit();

    if (inten) {
        i2c_enable_int(obj);
    } else {
        i2c_disable_int(obj);
    }

    return inten_back;
}

static int i2c_do_tran(i2c_t *obj, char *buf, int length, int read, int naklastdata)
{
    if (! buf || ! length) {
        return 0;
    }

    int tran_len = 0;

    i2c_disable_int(obj);
    obj->i2c.tran_ctrl = naklastdata ? (TRANCTRL_STARTED | TRANCTRL_NAKLASTDATA) : TRANCTRL_STARTED;
    obj->i2c.tran_beg = buf;
    obj->i2c.tran_pos = buf;
    obj->i2c.tran_end = buf + length;
    i2c_enable_int(obj);

    if (i2c_poll_tran_heatbeat_timeout(obj, NU_I2C_TIMEOUT_STAT_INT)) {
        // N/A
    } else {
        i2c_disable_int(obj);
        tran_len = obj->i2c.tran_pos - obj->i2c.tran_beg;
        obj->i2c.tran_beg = NULL;
        obj->i2c.tran_pos = NULL;
        obj->i2c.tran_end = NULL;
        i2c_enable_int(obj);
    }

    return tran_len;
}

static int i2c_do_trsn(i2c_t *obj, uint32_t i2c_ctl, int sync)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);
    int err = 0;

    i2c_disable_int(obj);

    if (i2c_poll_status_timeout(obj, i2c_is_trsn_done, NU_I2C_TIMEOUT_STAT_INT)) {
        err = I2C_ERROR_BUS_BUSY;
    } else {
        // NOTE: Avoid duplicate Start/Stop. Otherwise, we may meet strange error.
        uint32_t status = I2C_GET_STATUS(i2c_base);

        switch (status) {
        case 0x08:  // Start
        case 0x10:  // Master Repeat Start
            if (i2c_ctl & I2C_CTL0_STA_Msk) {
                return 0;
            } else {
                break;
            }
        case 0xF8:  // Bus Released
            if ((i2c_ctl & (I2C_CTL0_STA_Msk | I2C_CTL0_STO_Msk)) == I2C_CTL0_STO_Msk) {
                return 0;
            } else {
                break;
            }
        }
        I2C_SET_CONTROL_REG(i2c_base, i2c_ctl);
        if (sync && i2c_poll_status_timeout(obj, i2c_is_trsn_done, NU_I2C_TIMEOUT_STAT_INT)) {
            err = I2C_ERROR_BUS_BUSY;
        }
    }

    i2c_enable_int(obj);

    return err;
}

static int i2c_poll_status_timeout(i2c_t *obj, int (*is_status)(i2c_t *obj), uint32_t timeout)
{
    uint32_t t1, t2, elapsed = 0;
    int status_assert = 0;

    t1 = us_ticker_read();
    while (1) {
        status_assert = is_status(obj);
        if (status_assert) {
            break;
        }

        t2 = us_ticker_read();
        elapsed = (t2 > t1) ? (t2 - t1) : ((uint64_t) t2 + 0xFFFFFFFF - t1 + 1);
        if (elapsed >= timeout) {
            break;
        }
    }

    return (elapsed >= timeout);
}

static int i2c_poll_tran_heatbeat_timeout(i2c_t *obj, uint32_t timeout)
{
    uint32_t t1, t2, elapsed = 0;
    int tran_started;
    char *tran_pos = NULL;
    char *tran_pos2 = NULL;

    i2c_disable_int(obj);
    tran_pos = obj->i2c.tran_pos;
    i2c_enable_int(obj);
    t1 = us_ticker_read();
    while (1) {
        i2c_disable_int(obj);
        tran_started = i2c_is_tran_started(obj);
        i2c_enable_int(obj);
        if (! tran_started) {    // Transfer completed or stopped
            break;
        }

        i2c_disable_int(obj);
        tran_pos2 = obj->i2c.tran_pos;
        i2c_enable_int(obj);
        t2 = us_ticker_read();
        if (tran_pos2 != tran_pos) {    // Transfer on-going
            t1 = t2;
            tran_pos = tran_pos2;
            continue;
        }

        elapsed = (t2 > t1) ? (t2 - t1) : ((uint64_t) t2 + 0xFFFFFFFF - t1 + 1);
        if (elapsed >= timeout) {   // Transfer idle
            break;
        }
    }

    return (elapsed >= timeout);
}

#if 0
static int i2c_is_stat_int(i2c_t *obj)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);

    return !! (i2c_base->CTL0 & I2C_CTL0_SI_Msk);
}

static int i2c_is_stop_det(i2c_t *obj)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);

    return ! (i2c_base->CTL0 & I2C_CTL0_STO_Msk);
}
#endif

static int i2c_is_trsn_done(i2c_t *obj)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);
    int i2c_int;
    uint32_t status;
    int inten_back;

    inten_back = i2c_set_int(obj, 0);
    i2c_int = !! (i2c_base->CTL0 & I2C_CTL0_SI_Msk);
    status = I2C_GET_STATUS(i2c_base);
    i2c_set_int(obj, inten_back);

    return (i2c_int || status == 0xF8);
}

static int i2c_is_tran_started(i2c_t *obj)
{
    int started;
    int inten_back;

    inten_back = i2c_set_int(obj, 0);
    started = !! (obj->i2c.tran_ctrl & TRANCTRL_STARTED);
    i2c_set_int(obj, inten_back);

    return started;
}

static int i2c_addr2data(int address, int read)
{
    return read ? (address | 1) : (address & 0xFE);
}

static void i2c0_vec(void)
{
    i2c_irq(i2c0_var.obj);
}
static void i2c1_vec(void)
{
    i2c_irq(i2c1_var.obj);
}
static void i2c2_vec(void)
{
    i2c_irq(i2c2_var.obj);
}

static void i2c_irq(i2c_t *obj)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);
    uint32_t status;

    if (I2C_GET_TIMEOUT_FLAG(i2c_base)) {
        I2C_ClearTimeoutFlag(i2c_base);
        return;
    }

    status = I2C_GET_STATUS(i2c_base);

    switch (status) {
    // Master Transmit
    case 0x28:  // Master Transmit Data ACK
    case 0x18:  // Master Transmit Address ACK
    case 0x08:  // Start
    case 0x10:  // Master Repeat Start
        if ((obj->i2c.tran_ctrl & TRANCTRL_STARTED) && obj->i2c.tran_pos) {
            if (obj->i2c.tran_pos < obj->i2c.tran_end) {
                I2C_SET_DATA(i2c_base, *obj->i2c.tran_pos ++);
                I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk);
            } else {
                i2c_fsm_tranfini(obj, 0);
            }
        } else {
            i2c_disable_int(obj);
        }
        break;

    case 0x30:  // Master Transmit Data NACK
        i2c_fsm_tranfini(obj, 1);
        break;

    case 0x20:  // Master Transmit Address NACK
        i2c_fsm_tranfini(obj, 1);
        break;

    case 0x38:  // Master Arbitration Lost
        i2c_fsm_reset(obj, I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk);
        break;

    case 0x48:  // Master Receive Address NACK
        i2c_fsm_tranfini(obj, 1);
        break;

    case 0x40:  // Master Receive Address ACK
    case 0x50:  // Master Receive Data ACK
    case 0x58:  // Master Receive Data NACK
        if ((obj->i2c.tran_ctrl & TRANCTRL_STARTED) && obj->i2c.tran_pos) {
            if (obj->i2c.tran_pos < obj->i2c.tran_end) {
                if (status == 0x50 || status == 0x58) {
                    *obj->i2c.tran_pos ++ = I2C_GET_DATA(i2c_base);
                }

                if (status == 0x58) {
                    i2c_fsm_tranfini(obj, 1);
                } else {
                    uint32_t i2c_ctl = I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk;
                    if ((obj->i2c.tran_end - obj->i2c.tran_pos) == 1 &&
                            obj->i2c.tran_ctrl & TRANCTRL_NAKLASTDATA) {
                        // Last data
                        i2c_ctl &= ~I2C_CTL0_AA_Msk;
                    }
                    I2C_SET_CONTROL_REG(i2c_base, i2c_ctl);
                }
            } else {
                obj->i2c.tran_ctrl &= ~TRANCTRL_STARTED;
                i2c_disable_int(obj);
                break;
            }
        } else {
            i2c_disable_int(obj);
        }
        break;

    //case 0x00:  // Bus error

    // Slave Transmit
    case 0xB8:  // Slave Transmit Data ACK
    case 0xA8:  // Slave Transmit Address ACK
    case 0xB0:  // Slave Transmit Arbitration Lost
        if ((obj->i2c.tran_ctrl & TRANCTRL_STARTED) && obj->i2c.tran_pos) {
            if (obj->i2c.tran_pos < obj->i2c.tran_end) {
                uint32_t i2c_ctl = I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk;

                I2C_SET_DATA(i2c_base, *obj->i2c.tran_pos ++);
                if (obj->i2c.tran_pos == obj->i2c.tran_end &&
                        obj->i2c.tran_ctrl & TRANCTRL_NAKLASTDATA) {
                    // Last data
                    i2c_ctl &= ~I2C_CTL0_AA_Msk;
                }
                I2C_SET_CONTROL_REG(i2c_base, i2c_ctl);
            } else {
                obj->i2c.tran_ctrl &= ~TRANCTRL_STARTED;
                i2c_disable_int(obj);
                break;
            }
        } else {
            i2c_disable_int(obj);
        }
        obj->i2c.slaveaddr_state = ReadAddressed;
        break;
    //case 0xA0:  // Slave Transmit Repeat Start or Stop
    case 0xC0:  // Slave Transmit Data NACK
    case 0xC8:  // Slave Transmit Last Data ACK
        obj->i2c.slaveaddr_state = NoData;
        i2c_fsm_reset(obj, I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk);
        break;

    // Slave Receive
    case 0x80:  // Slave Receive Data ACK
    case 0x88:  // Slave Receive Data NACK
    case 0x60:  // Slave Receive Address ACK
    case 0x68:  // Slave Receive Arbitration Lost
        obj->i2c.slaveaddr_state = WriteAddressed;
        if ((obj->i2c.tran_ctrl & TRANCTRL_STARTED) && obj->i2c.tran_pos) {
            if (obj->i2c.tran_pos < obj->i2c.tran_end) {
                if (status == 0x80 || status == 0x88) {
                    *obj->i2c.tran_pos ++ = I2C_GET_DATA(i2c_base);
                }

                if (status == 0x88) {
                    obj->i2c.slaveaddr_state = NoData;
                    i2c_fsm_reset(obj, I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk);
                } else {
                    uint32_t i2c_ctl = I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk;
                    if ((obj->i2c.tran_end - obj->i2c.tran_pos) == 1 &&
                            obj->i2c.tran_ctrl & TRANCTRL_NAKLASTDATA) {
                        // Last data
                        i2c_ctl &= ~I2C_CTL0_AA_Msk;
                    }
                    I2C_SET_CONTROL_REG(i2c_base, i2c_ctl);
                }
            } else {
                obj->i2c.tran_ctrl &= ~TRANCTRL_STARTED;
                i2c_disable_int(obj);
                break;
            }
        } else {
            i2c_disable_int(obj);
        }
        break;
    //case 0xA0:  // Slave Receive Repeat Start or Stop

    // GC mode
    //case 0xA0:  // GC mode Repeat Start or Stop
    case 0x90:  // GC mode Data ACK
    case 0x98:  // GC mode Data NACK
    case 0x70:  // GC mode Address ACK
    case 0x78:  // GC mode Arbitration Lost
        obj->i2c.slaveaddr_state = WriteAddressed;
        if ((obj->i2c.tran_ctrl & TRANCTRL_STARTED) && obj->i2c.tran_pos) {
            if (obj->i2c.tran_pos < obj->i2c.tran_end) {
                if (status == 0x90 || status == 0x98) {
                    *obj->i2c.tran_pos ++ = I2C_GET_DATA(i2c_base);
                }

                if (status == 0x98) {
                    obj->i2c.slaveaddr_state = NoData;
                    i2c_fsm_reset(obj, I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk);
                } else {
                    uint32_t i2c_ctl = I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk;
                    if ((obj->i2c.tran_end - obj->i2c.tran_pos) == 1 &&
                            obj->i2c.tran_ctrl & TRANCTRL_NAKLASTDATA) {
                        // Last data
                        i2c_ctl &= ~I2C_CTL0_AA_Msk;
                    }
                    I2C_SET_CONTROL_REG(i2c_base, i2c_ctl);
                }
            } else {
                obj->i2c.tran_ctrl &= ~TRANCTRL_STARTED;
                i2c_disable_int(obj);
                break;
            }
        } else {
            i2c_disable_int(obj);
        }
        break;

    case 0xF8:  // Bus Released
        break;

    default:
        i2c_fsm_reset(obj, I2C_CTL0_SI_Msk | I2C_CTL0_AA_Msk);
    }
}

static void i2c_fsm_reset(i2c_t *obj, uint32_t i2c_ctl)
{
    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);

    obj->i2c.stop = 0;

    obj->i2c.tran_ctrl = 0;

    I2C_SET_CONTROL_REG(i2c_base, i2c_ctl);
    obj->i2c.slaveaddr_state = NoData;
}

static void i2c_fsm_tranfini(i2c_t *obj, int lastdatanaked)
{
    if (lastdatanaked) {
        obj->i2c.tran_ctrl |= TRANCTRL_LASTDATANAKED;
    }

    obj->i2c.tran_ctrl &= ~TRANCTRL_STARTED;
    i2c_disable_int(obj);
}

#if DEVICE_I2C_ASYNCH

void i2c_transfer_asynch(i2c_t *obj, const void *tx, size_t tx_length, void *rx, size_t rx_length, uint32_t address, uint32_t stop, uint32_t handler, uint32_t event, DMAUsage hint)
{
    // NOTE: M451 I2C only supports 7-bit slave address. The mbed I2C address passed in is shifted left by 1 bit (7-bit addr << 1).
    MBED_ASSERT((address & 0xFFFFFF00) == 0);

    // NOTE: First transmit and then receive.

    (void) hint;
    obj->i2c.dma_usage = DMA_USAGE_NEVER;
    obj->i2c.stop = stop;
    obj->i2c.address = address;
    obj->i2c.event = event;
    i2c_buffer_set(obj, tx, tx_length, rx, rx_length);

    i2c_enable_vector_interrupt(obj, handler, 1);
    i2c_start(obj);
}

uint32_t i2c_irq_handler_asynch(i2c_t *obj)
{
    int event = 0;

    I2C_T *i2c_base = (I2C_T *) NU_MODBASE(obj->i2c.i2c);
    uint32_t status = I2C_GET_STATUS(i2c_base);
    switch (status) {
    case 0x08:  // Start
    case 0x10: {// Master Repeat Start
        if (obj->tx_buff.buffer && obj->tx_buff.pos < obj->tx_buff.length) {
            I2C_SET_DATA(i2c_base, (i2c_addr2data(obj->i2c.address, 0)));
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_SI_Msk);
        } else if (obj->rx_buff.buffer && obj->rx_buff.pos < obj->rx_buff.length) {
            I2C_SET_DATA(i2c_base, (i2c_addr2data(obj->i2c.address, 1)));
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_SI_Msk);
        } else {
            event = I2C_EVENT_TRANSFER_COMPLETE;
            if (obj->i2c.stop) {
                I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk);
            }
        }
        break;
    }

    case 0x18:  // Master Transmit Address ACK
    case 0x28:  // Master Transmit Data ACK
        if (obj->tx_buff.buffer && obj->tx_buff.pos < obj->tx_buff.length) {
            uint8_t *tx = (uint8_t *)obj->tx_buff.buffer;
            I2C_SET_DATA(i2c_base, tx[obj->tx_buff.pos ++]);
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_SI_Msk);
        } else if (obj->rx_buff.buffer && obj->rx_buff.pos < obj->rx_buff.length) {
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STA_Msk | I2C_CTL0_SI_Msk);
        } else {
            event = I2C_EVENT_TRANSFER_COMPLETE;
            if (obj->i2c.stop) {
                I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk);
            }
        }
        break;

    case 0x20:  // Master Transmit Address NACK
        event = I2C_EVENT_ERROR_NO_SLAVE;
        if (obj->i2c.stop) {
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk);
        }
        break;

    case 0x30:  // Master Transmit Data NACK
        if (obj->tx_buff.buffer && obj->tx_buff.pos < obj->tx_buff.length) {
            event = I2C_EVENT_TRANSFER_EARLY_NACK;
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk);
        } else if (obj->rx_buff.buffer && obj->rx_buff.pos < obj->rx_buff.length) {
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STA_Msk | I2C_CTL0_SI_Msk);
        } else {
            event = I2C_EVENT_TRANSFER_COMPLETE;
            if (obj->i2c.stop) {
                I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk);
            }
        }
        break;

    case 0x38:  // Master Arbitration Lost
        I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_SI_Msk);  // Enter not addressed SLV mode
        event = I2C_EVENT_ERROR;
        break;

    case 0x50:  // Master Receive Data ACK
        if (obj->rx_buff.buffer && obj->rx_buff.pos < obj->rx_buff.length) {
            uint8_t *rx = (uint8_t *) obj->rx_buff.buffer;
            rx[obj->rx_buff.pos ++] = I2C_GET_DATA(((I2C_T *) NU_MODBASE(obj->i2c.i2c)));
        }
    case 0x40:  // Master Receive Address ACK
        I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_SI_Msk | ((obj->rx_buff.pos != obj->rx_buff.length - 1) ? I2C_CTL0_AA_Msk : 0));
        break;

    case 0x48:  // Master Receive Address NACK
        event = I2C_EVENT_ERROR_NO_SLAVE;
        if (obj->i2c.stop) {
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk);
        }
        break;

    case 0x58:  // Master Receive Data NACK
        if (obj->rx_buff.buffer && obj->rx_buff.pos < obj->rx_buff.length) {
            uint8_t *rx = (uint8_t *) obj->rx_buff.buffer;
            rx[obj->rx_buff.pos ++] = I2C_GET_DATA(((I2C_T *) NU_MODBASE(obj->i2c.i2c)));
        }
        I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STA_Msk | I2C_CTL0_SI_Msk);
        break;

    case 0x00:  // Bus error
        event = I2C_EVENT_ERROR;
        i2c_reset(obj);
        break;

    default:
        event = I2C_EVENT_ERROR;
        if (obj->i2c.stop) {
            I2C_SET_CONTROL_REG(i2c_base, I2C_CTL0_STO_Msk | I2C_CTL0_SI_Msk);
        }
    }

    if (event) {
        i2c_rollback_vector_interrupt(obj);
    }

    return (event & obj->i2c.event);
}

uint8_t i2c_active(i2c_t *obj)
{
    const struct nu_modinit_s *modinit = get_modinit(obj->i2c.i2c, i2c_modinit_tab);
    MBED_ASSERT(modinit != NULL);
    MBED_ASSERT(modinit->modname == (int) obj->i2c.i2c);

    // Vector will be changed for async transfer. Use it to judge if async transfer is on-going.
    uint32_t vec = NVIC_GetVector(modinit->irq_n);
    struct nu_i2c_var *var = (struct nu_i2c_var *) modinit->var;
    return (vec && vec != (uint32_t) var->vec);
}

void i2c_abort_asynch(i2c_t *obj)
{
    i2c_rollback_vector_interrupt(obj);
    i2c_stop(obj);
}

static void i2c_buffer_set(i2c_t *obj, const void *tx, size_t tx_length, void *rx, size_t rx_length)
{
    obj->tx_buff.buffer = (void *) tx;
    obj->tx_buff.length = tx_length;
    obj->tx_buff.pos = 0;
    obj->rx_buff.buffer = rx;
    obj->rx_buff.length = rx_length;
    obj->rx_buff.pos = 0;
}

static void i2c_enable_vector_interrupt(i2c_t *obj, uint32_t handler, int enable)
{
    const struct nu_modinit_s *modinit = get_modinit(obj->i2c.i2c, i2c_modinit_tab);
    MBED_ASSERT(modinit != NULL);
    MBED_ASSERT(modinit->modname == (int) obj->i2c.i2c);

    if (enable) {
        NVIC_SetVector(modinit->irq_n, handler);
        i2c_enable_int(obj);
    } else {
        i2c_disable_int(obj);
    }

}

static void i2c_rollback_vector_interrupt(i2c_t *obj)
{
    const struct nu_modinit_s *modinit = get_modinit(obj->i2c.i2c, i2c_modinit_tab);
    MBED_ASSERT(modinit != NULL);
    MBED_ASSERT(modinit->modname == (int) obj->i2c.i2c);

    struct nu_i2c_var *var = (struct nu_i2c_var *) modinit->var;
    i2c_enable_vector_interrupt(obj, (uint32_t) var->vec, 1);
}

#endif

#endif