Heater files
Dependents: LEX-Demo-Firmware-Logging LEX-Demo-Firmware-Logging
Heater.cpp
- Committer:
- omatthews
- Date:
- 2019-08-06
- Revision:
- 21:085b53e06065
- Parent:
- 19:fccdd7127f94
File content as of revision 21:085b53e06065:
/*------------------------------------------------------------------------------ Library code file for interface to Heater Date: 16/07/2018 ------------------------------------------------------------------------------*/ #include "mbed.h" #include "MODSERIAL.h" #include "Heater.h" #include "ADS8568_ADC.h" extern ADS8568_ADC adc; extern Timer timer; extern DigitalIn adc_busy; extern MODSERIAL pc; extern int log_count; extern float R_avg; Heater::Heater(const int i_port, const int v_port, FastPWM * drive, FastPWM * guard, const float corr_grad, const float corr_int, float R_ref) :R_ref(R_ref),i_port(i_port),v_port(v_port),drive(drive),guard(guard),corr_grad(corr_grad),corr_int(corr_int) {} // Convert from R to T using the linear relationship - T = R * corr_grad + corr_int float Heater::R_to_T(const float R) const {return R*corr_grad + corr_int;} float Heater::T_to_R(const float T) const {return (T - corr_int)/corr_grad;} void Heater::output()const { //Prints the current state to the terminal pc.printf("%d,%f,%f,%f,%f,%f\n",log_count,R_ref,R,error,error_integrated,drive->read()); } void Heater::read() { //Reads R and then resets the drive back to its previous value int i = 0; //float error_prev = error; double drive_prev = drive->read(); //Store previous value of drive drive->period_us(1); //Set period to 1us for the measurement *drive = 1.0f; //Turn the driver on for the measurement wait_us(MEAS_DELAY); //Wait for ADC to settle adc.start_conversion(ALL_CH); //Incremental back off until ADC is free while(adc_busy == 1) { wait_us(1); i++; } drive->write(drive_prev); //Reset the duty cycle back to what it was drive->period_us(PWM_PERIOD); //Reset the period to what it was //Get voltage, current and R values from the ADC conversion adc.read_channels(); curr = adc.read_channel_result(i_port); v = adc.read_channel_result(v_port); if (curr > 0) {R = (float)v/curr;} //Avoid dividing by 0 //Get error values error = R_ref - R; //error_diff = (error - error_prev)/WAIT_DELAY; //Avoid integral windup by limiting error past actuation saturation (actuator does saturate for any negative error, but to ensure integrated error can decrease, the limit has been set to the negative of the positive limit //if (error*Kp > WIND_UP_LIMIT) {error_integrated += WIND_UP_LIMIT/Kp;} //else if (error*Kp < -WIND_UP_LIMIT) {error_integrated -= WIND_UP_LIMIT/Kp;} if (error < WIND_UP_LIMIT && error > -WIND_UP_LIMIT) {error_integrated += error;} //Output the error every LOG_LIM reads log_count++; } void Heater::hold(const int hold_time) { //Holds the heater at R_ref for the given hold time // in: int hold_time - is the time in ms to hold the reference int end_time = timer.read_ms() + hold_time; while (timer.read_ms() < end_time) { read(); drive->write((double) (Kp * (error + error_integrated/Ti))); guard->write((double) (Kp * GUARD_PWM_RATIO * (error + error_integrated/Ti))); wait_ms(WAIT_DELAY); //Wait before reading again } } void Heater::ramp_R(const int ramp_time, const float R_final, const float R_start) { //Ramps the heater from R_start to R_final for the given hold time // in: int hold_time - is the time in ms to hold the reference // float R_final - is the final R_ref value // float R_start - is the initial R_ref value int time = timer.read_ms(); int start_time = time; int end_time = start_time + ramp_time; float ramp_rate = (R_final - R_start)/ramp_time; while (time < end_time) { Set_R_ref(R_start + ramp_rate * (time - start_time)); hold(1); time = timer.read_ms(); } } void Heater::ramp_T(const int ramp_time, const float T_final, const float T_start) { //Ramps the heater from T_start to T_final for the given hold time // in: int hold_time - is the time in ms to hold the reference // float T_final - is the final T_ref value // float T_start - is the initial T_ref value ramp_R(ramp_time, T_to_R(T_final), T_to_R(T_start)); } void Heater::Set_R_ref(float R) { R_ref = R; error_integrated = 0; } void Heater::Set_T_ref(float T_ref) {R_ref = T_to_R(T_ref);} void Heater::Set_D(float D) {drive->write(D);} int Heater::Get_i() const {return curr;} int Heater::Get_v() const {return v;} float Heater::Get_R() const {return R;} float Heater::Get_T() const {return R_to_T(R);} void Heater::turn_on () { *drive = 1; *guard = GUARD_PWM_RATIO; } void Heater::turn_off () { *drive = 0; *guard = 0; }