File content as of revision 28:0ed92c590607:

/*
 * Copyright (c) 2018 HELIOS Software GmbH
 * 30826 Garbsen (Hannover) Germany
 * Licensed under the Apache License, Version 2.0);
 */
  
 /*
 * For Wiring Instructions, please visit the link below:
 * https://www.hackster.io/DevinAlex64/getting-started-with-the-max32620fthr-and-lora-f9d8dd\
 */
 
 #include "main.h"
 #include "global_buffers.h"
 #include "GridEye.h"


/* If the board that is compiled is the master device (BLE enabled MAX32630FTHR),
 * then it needs this library and needs to be configed in order for the device to 
 * work with a 3.3volt output instead of a 1.8 volt output. 
 * 
 * This is only needed for the MAX32630FTHR. The MAX325620FTHR is exampt from this 
 * additional setup in the main program.
 */ 
 #if defined(TARGET_MAX32630FTHR) // using the RFM95 board
   #include "max32630fthr.h"
    MAX32630FTHR pegasus(MAX32630FTHR::VIO_3V3);
 #endif

DigitalOut myled(LED);

Serial pc(USBTX, USBRX);


#if   defined(TARGET_MAX32630FTHR) // Master Device: MAX32630FTHR BLE-to-LoRa Gateway
    /* No grid eye object needed. The function the master uses to convert the raw 
     * data that is sent over from the slave deevice that contains the data from the
     * actual grid eye sensor is actually a function that is not part of the grid eye
     * class. this is due to the fact that the grid eye class requires n i2c bus to 
     * be assigned to a phyiscal sensor. In this case, the library for the Grid Eye 
     * sensor has a support functin that is used to convert data that is aquired from 
     * the grid eye sensor. So it is not supposed to be a class specific function.
    */
#elif defined(TARGET_MAX32620FTHR) // Slave Device: Robot
    //Init I2C communications in default I2C bus I2C #1
    I2C i2cGridEye(P3_4,P3_5);
    GridEye gridEye(i2cGridEye);
#endif

int main() 
{
    /*
     * inits the Serial or USBSerial when available (230400 baud).
     * If the serial uart is not is not connected it swiches to USB Serial
     * blinking LED means USBSerial detected, waiting for a connect.
     * It waits up to 30 seconds for a USB terminal connections 
     */
    InitSerial(30*1000, &myled);
    dprintf("Welcome to the SX1276GenericLib");
  
    dprintf("Starting a simple LoRa PingPong");
    
    /* Setup begins here: */
    #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
        dprintf("MAX32630FTHR: Master");
    #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
        dprintf("MAX32620FTHR: Slave");
    #endif
    
    
    /***************************************************************************
     * Grid Eye Sensor: Non-Buffer Program Variables
     **************************************************************************/
    #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
        int frame_idx = 0;
    #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
        // none yet
        int frame_idx = 0;
    #endif
    
    
    /***************************************************************************
     * Combined Payload Buffers for LoRa Communications
     **************************************************************************/
    uint8_t BufferTx[BufferSizeTx];
    uint8_t BufferRx[BufferSizeRx];
    
    /***************************************************************************
     * BLE Data Buffers
     **************************************************************************/
    #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
        uint8_t curr_ble_to_slave[size_of_ble];
    #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
        uint8_t curr_ble_from_master[size_of_ble];
        uint8_t prev_ble_from_master[size_of_ble];
    #endif
    
    /***************************************************************************
     * Grid Eye Sensor Data Buffers
     **************************************************************************/
    #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
        char curr_raw_frame_from_slave[size_of_grid_eye];
        char prev_raw_frame_from_slave[size_of_grid_eye];
        int16_t conv_frame_from_slave[64];
    #elif defined(TARGET_MAX32620FTHR) // Client Device: LoRa Controlled Robot
        char curr_raw_frame_to_master[size_of_grid_eye];
        char prev_raw_frame_to_master[size_of_grid_eye];
        int16_t conv_frame_to_master[64];
    #endif
    
    /***************************************************************************
     * GPS Data Buffers
     **************************************************************************/
    #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
        uint8_t curr_gps_from_slave[size_of_gps];
        uint8_t prev_gps_from_slave[size_of_gps];
    #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
        uint8_t curr_gps_to_master[size_of_gps];
    #endif
    
    /***************************************************************************
     * MAX17055 Data Buffers
     **************************************************************************/
    #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
        uint8_t curr_MAX17055_from_slave[size_of_MAX17055];
        uint8_t prev_MAX17055_from_slave[size_of_MAX17055];
    #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
        uint8_t curr_MAX17055_to_master[size_of_MAX17055];
    #endif
    
    /***************************************************************************
     * MAX77650 Data Buffers
     **************************************************************************/
    #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
        uint8_t curr_MAX77650_from_slave[size_of_MAX77650];
        uint8_t prev_MAX77650_from_slave[size_of_MAX77650];
    #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
        uint8_t curr_MAX77650_to_master[size_of_MAX77650];
    #endif
    
    /***************************************************************************
     * Finish Setting up LoRa Radios: This passes in pointers to Buffers to send
     **************************************************************************/
    SX1276PingPongSetup(BufferTx, BufferRx);
    
    while(1) 
    {        
        /***************************************************************************
         * Grid Eye Sensor 
         **************************************************************************/
        #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
            // Check to see if the contents of the previous scan are the same. If they are different then continue with converting
            if( memcmp(prev_raw_frame_from_slave, curr_raw_frame_from_slave, sizeof(curr_raw_frame_from_slave)) != 0 )
            {
                // Convert raw data sent from slave to a 16 bit integer array by calling this
                convRaw8x8Data2Point25degC(curr_raw_frame_from_slave, conv_frame_from_slave);
                
                // Next Print off the Converted data
                pc.printf("\r\nFrame %d data: \r\n", frame_idx);
                uint8_t idx;
                float pixel_data;
                for (int y = 0; y < 8; y++) {
                    for (int x = 0; x < 8; x++) {
                        idx = y*8 + x;
                        pixel_data = ((float)conv_frame_from_slave[idx])/4.0;
                        pc.printf("%.2f  \t", pixel_data);
                    }
                    pc.printf("\r\n\r\n");
                }
                pc.printf("\r\n");
                
                // Increment frame counter
                frame_idx = frame_idx +1;
            }
            
            /* Next copy in data received from current data into buffer used for
             * comparison next time the memcmp above is called. This prevents the 
             * program from converting the same raw data aquired by the grid eye
             * sensor on the slave device to the floating point array with the 
             * 0.25 degrees celsius precision level when there is not new data. 
             */
            memcpy(prev_raw_frame_from_slave, curr_raw_frame_from_slave, sizeof(curr_raw_frame_from_slave));
            
        #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
            // Aquire raw data about 8x8 frame from the grid eye sensor in this function call 
            gridEye.getRaw8x8FrameData(curr_raw_frame_to_master);
            wait_ms( 10 );
            /*
            //if ( memcmp(prev_raw_frame_to_master, curr_raw_frame_to_master, sizeof(curr_raw_frame_to_master)) != 0 )
            //{
                // Convert raw data sent from slave to a 16 bit integer array by calling this
                convRaw8x8Data2Point25degC(curr_raw_frame_to_master, conv_frame_to_master);
                
                // Next Print off the Converted data
                pc.printf("\r\nFrame %d data: \r\n", frame_idx);
                uint8_t idx;
                float pixel_data;
                for (int y = 0; y < 8; y++) {
                    for (int x = 0; x < 8; x++) {
                        idx = y*8 + x;
                        pixel_data = conv_frame_to_master[idx]/4.0;
                        pc.printf("%.2f  \t", pixel_data);
                    }
                    pc.printf("\r\n\r\n");
                }
                pc.printf("\r\n");
                
                // Increment frame counter
                frame_idx = frame_idx +1;
            //}
            */
            memcpy(prev_raw_frame_to_master, curr_raw_frame_to_master, sizeof(curr_raw_frame_to_master));
        #endif
        
        
        /***************************************************************************
         * Fill Payload Buffer With Data From Sensors for LoRa Transmition
         **************************************************************************/
        #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
            memcpy(&BufferTx[tx_idx_signature], PingMsg,           size_signature);
            memcpy(&BufferTx[tx_idx_ble],       curr_ble_to_slave, size_of_ble);
        #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
            memcpy(&BufferTx[tx_idx_signature], PongMsg,                  size_signature);
            memcpy(&BufferTx[tx_idx_grid_eye],  curr_raw_frame_to_master, size_of_grid_eye);
            memcpy(&BufferTx[tx_idx_gps],       curr_gps_to_master,       size_of_gps);
            memcpy(&BufferTx[tx_idx_MAX17055],  curr_MAX17055_to_master,  size_of_MAX17055);
            memcpy(&BufferTx[tx_idx_MAX77650],  curr_MAX77650_to_master,  size_of_MAX77650);
        #endif
        
        
        
        /***************************************************************************
         * Lora Communications
         **************************************************************************/
        wait_ms( 10 );  
        SX1276PingPong();
        
        /***************************************************************************
         * Fill Global Buffers With Data From Received Payload Buffer
         **************************************************************************/
        /* The master and slave devices will have different requirements for offloading payload */
        #if   defined(TARGET_MAX32630FTHR) // Master Device: BLE-to-LoRa Gateway
            memcpy(curr_raw_frame_from_slave, &BufferRx[rx_idx_grid_eye], size_of_grid_eye);
            memcpy(curr_gps_from_slave,       &BufferRx[rx_idx_gps],      size_of_gps);
            memcpy(curr_MAX17055_from_slave,  &BufferRx[rx_idx_MAX17055], size_of_MAX17055);
            memcpy(curr_MAX77650_from_slave,  &BufferRx[rx_idx_MAX77650], size_of_MAX77650);
        #elif defined(TARGET_MAX32620FTHR) // Slave Device: LoRa Controlled Robot
            memcpy(curr_ble_from_master,      &BufferRx[rx_idx_ble],      size_of_ble);
        #endif
    
        
        
        
        
    }
    
}