Falling_Trigger_Management
[EXTI Exported Functions]

Disable ExtiLine Falling Edge Trigger for Lines in range 0 to 31.

Note:

The configurable wakeup lines are edge-triggered. No glitch must be generated on these lines. If a Falling edge on a configurable interrupt line occurs during a write operation in the EXTI_FTSR register, the pending bit is not set. Rising and falling edge triggers can be set for the same interrupt line. In this case, both generate a trigger condition. FTSR1 FTx LL_EXTI_DisableFallingTrig_0_31

Parameters:

ExtiLine

This parameter can be a combination of the following values: LL_EXTI_LINE_0 LL_EXTI_LINE_1 LL_EXTI_LINE_2 LL_EXTI_LINE_3 LL_EXTI_LINE_4 LL_EXTI_LINE_5 LL_EXTI_LINE_6 LL_EXTI_LINE_7 LL_EXTI_LINE_8 LL_EXTI_LINE_9 LL_EXTI_LINE_10 LL_EXTI_LINE_11 LL_EXTI_LINE_12 LL_EXTI_LINE_13 LL_EXTI_LINE_14 LL_EXTI_LINE_15 LL_EXTI_LINE_16 LL_EXTI_LINE_18 LL_EXTI_LINE_19 LL_EXTI_LINE_20 LL_EXTI_LINE_21 LL_EXTI_LINE_22 LL_EXTI_LINE_29 LL_EXTI_LINE_30 LL_EXTI_LINE_31

Note:

Please check each device line mapping for EXTI Line availability

Return values:

None

Definition at line 981 of file stm32l4xx_ll_exti.h.

Disable ExtiLine Falling Edge Trigger for Lines in range 32 to 63.

Note:

The configurable wakeup lines are edge-triggered. No glitch must be generated on these lines. If a Falling edge on a configurable interrupt line occurs during a write operation in the EXTI_FTSR register, the pending bit is not set. Rising and falling edge triggers can be set for the same interrupt line. In this case, both generate a trigger condition. FTSR2 FTx LL_EXTI_DisableFallingTrig_32_63

Parameters:

ExtiLine

This parameter can be a combination of the following values: LL_EXTI_LINE_35 LL_EXTI_LINE_36 LL_EXTI_LINE_37 LL_EXTI_LINE_38

Return values:

None

Definition at line 1002 of file stm32l4xx_ll_exti.h.

Enable ExtiLine Falling Edge Trigger for Lines in range 0 to 31.

Note:

The configurable wakeup lines are edge-triggered. No glitch must be generated on these lines. If a falling edge on a configurable interrupt line occurs during a write operation in the EXTI_FTSR register, the pending bit is not set. Rising and falling edge triggers can be set for the same interrupt line. In this case, both generate a trigger condition. FTSR1 FTx LL_EXTI_EnableFallingTrig_0_31

Parameters:

ExtiLine

This parameter can be a combination of the following values: LL_EXTI_LINE_0 LL_EXTI_LINE_1 LL_EXTI_LINE_2 LL_EXTI_LINE_3 LL_EXTI_LINE_4 LL_EXTI_LINE_5 LL_EXTI_LINE_6 LL_EXTI_LINE_7 LL_EXTI_LINE_8 LL_EXTI_LINE_9 LL_EXTI_LINE_10 LL_EXTI_LINE_11 LL_EXTI_LINE_12 LL_EXTI_LINE_13 LL_EXTI_LINE_14 LL_EXTI_LINE_15 LL_EXTI_LINE_16 LL_EXTI_LINE_18 LL_EXTI_LINE_19 LL_EXTI_LINE_20 LL_EXTI_LINE_21 LL_EXTI_LINE_22 LL_EXTI_LINE_29 LL_EXTI_LINE_30 LL_EXTI_LINE_31

Note:

Please check each device line mapping for EXTI Line availability

Return values:

None

Definition at line 916 of file stm32l4xx_ll_exti.h.

Enable ExtiLine Falling Edge Trigger for Lines in range 32 to 63.

Note:

The configurable wakeup lines are edge-triggered. No glitch must be generated on these lines. If a Falling edge on a configurable interrupt line occurs during a write operation in the EXTI_FTSR register, the pending bit is not set. Rising and falling edge triggers can be set for the same interrupt line. In this case, both generate a trigger condition. FTSR2 FTx LL_EXTI_EnableFallingTrig_32_63

Parameters:

ExtiLine

This parameter can be a combination of the following values: LL_EXTI_LINE_35 LL_EXTI_LINE_36 LL_EXTI_LINE_37 LL_EXTI_LINE_38

Return values:

None

Definition at line 938 of file stm32l4xx_ll_exti.h.

Check if falling edge trigger is enabled for Lines in range 0 to 31 FTSR1 FTx LL_EXTI_IsEnabledFallingTrig_0_31.

Parameters:

ExtiLine

This parameter can be a combination of the following values: LL_EXTI_LINE_0 LL_EXTI_LINE_1 LL_EXTI_LINE_2 LL_EXTI_LINE_3 LL_EXTI_LINE_4 LL_EXTI_LINE_5 LL_EXTI_LINE_6 LL_EXTI_LINE_7 LL_EXTI_LINE_8 LL_EXTI_LINE_9 LL_EXTI_LINE_10 LL_EXTI_LINE_11 LL_EXTI_LINE_12 LL_EXTI_LINE_13 LL_EXTI_LINE_14 LL_EXTI_LINE_15 LL_EXTI_LINE_16 LL_EXTI_LINE_18 LL_EXTI_LINE_19 LL_EXTI_LINE_20 LL_EXTI_LINE_21 LL_EXTI_LINE_22 LL_EXTI_LINE_29 LL_EXTI_LINE_30 LL_EXTI_LINE_31

Note:

Please check each device line mapping for EXTI Line availability

Return values:

State

of bit (1 or 0).

Definition at line 1039 of file stm32l4xx_ll_exti.h.

Check if falling edge trigger is enabled for Lines in range 32 to 63 FTSR2 FTx LL_EXTI_IsEnabledFallingTrig_32_63.

Parameters:

ExtiLine

This parameter can be a combination of the following values: LL_EXTI_LINE_35 LL_EXTI_LINE_36 LL_EXTI_LINE_37 LL_EXTI_LINE_38

Return values:

State

of bit (1 or 0).

Definition at line 1054 of file stm32l4xx_ll_exti.h.