display funciona!
Dependents: 2018_I2C_LCD_03 TBI_FIAT_FEEDFORWARD Ignition Can_between_NUCLEOS_LCD ... more
Fork of TextLCD by
TextLCD_Config.h
- Committer:
- wim
- Date:
- 2014-10-10
- Revision:
- 35:311be6444a39
- Parent:
- 34:e5a0dcb43ecc
- Child:
- 36:9f5f86dfd44a
File content as of revision 35:311be6444a39:
/* mbed TextLCD Library, for a 4-bit LCD based on HD44780 * Copyright (c) 2014, WH * 2014, v01: WH, Extracted from TextLCD.h as of v14 * 2014, v02: WH, Added AC780 support, added I2C expander modules, fixed setBacklight() for inverted logic modules. Fixed bug in LCD_SPI_N define * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell * copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in * all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN * THE SOFTWARE. */ #ifndef MBED_TEXTLCDCONFIG_H #define MBED_TEXTLCDCONFIG_H //Select hardware interface options to reduce memory footprint (multiple options allowed) #define LCD_I2C 1 /* I2C Expander PCF8574/MCP23008 */ #define LCD_SPI 1 /* SPI Expander SN74595 */ #define LCD_I2C_N 1 /* Native I2C bus */ #define LCD_SPI_N 1 /* Native SPI bus */ #define LCD_SPI_N_3_9 1 /* Native SPI bus */ #define LCD_SPI_N_3_10 1 /* Native SPI bus */ #define LCD_SPI_N_3_16 1 /* Native SPI bus */ #define LCD_SPI_N_3_24 1 /* Native SPI bus */ //Select options to reduce memory footprint (multiple options allowed) #define LCD_UDC 1 /* Enable predefined UDC example*/ #define LCD_PRINTF 1 /* Enable Stream implementation */ //Pin Defines for I2C PCF8574/PCF8574A or MCP23008 and SPI 74595 bus expander interfaces //LCD and serial portexpanders should be wired accordingly // //Select Hardware module (one option only) #define DEFAULT 1 #define ADAFRUIT 0 #define DFROBOT 0 #define YWROBOT 0 #define GYLCD 0 #define SYDZ 0 //Select Hardware module (one option only) #if (DEFAULT==1) //Definitions for default (WH) mapping between serial port expander pins and LCD controller //This hardware supports the I2C bus expander (PCF8574/PCF8574A or MCP23008) and SPI bus expander (74595) interfaces //See https://mbed.org/cookbook/Text-LCD-Enhanced // //Note: LCD RW pin must be connected to GND // E2 is used for LCD40x4 (second controller) // BL may be used to control backlight #define D_LCD_PIN_D4 0 #define D_LCD_PIN_D5 1 #define D_LCD_PIN_D6 2 #define D_LCD_PIN_D7 3 #define D_LCD_PIN_RS 4 #define D_LCD_PIN_E 5 #define D_LCD_PIN_E2 6 #define D_LCD_PIN_BL 7 #define D_LCD_PIN_RW D_LCD_PIN_E2 //Select I2C Portexpander type (one option only) #define PCF8574 1 #define MCP23008 0 //Inverted Backlight control #define BACKLIGHT_INV 0 #endif #if (ADAFRUIT==1) //Definitions for Adafruit i2cspilcdbackpack mapping between serial port expander pins and LCD controller //This hardware supports both an I2C expander (MCP23008) and an SPI expander (74595) selectable by a jumper. //Slaveaddress may be set by solderbridges (default 0x40). SDA/SCL has pullup Resistors onboard. //See http://www.ladyada.net/products/i2cspilcdbackpack // //Note: LCD RW pin must be kept LOW // E2 is not available on this hardware and so it does not support LCD40x4 (second controller) // BL is used to control backlight #define D_LCD_PIN_0 0 #define D_LCD_PIN_RS 1 #define D_LCD_PIN_E 2 #define D_LCD_PIN_D4 3 #define D_LCD_PIN_D5 4 #define D_LCD_PIN_D6 5 #define D_LCD_PIN_D7 6 #define D_LCD_PIN_BL 7 #define D_LCD_PIN_E2 D_LCD_PIN_0 //Force I2C portexpander type #define PCF8574 0 #define MCP23008 1 //Inverted Backlight control #define BACKLIGHT_INV 0 #endif #if (DFROBOT==1) //Definitions for DFROBOT LCD2004 Module mapping between serial port expander pins and LCD controller //This hardware uses PCF8574 and is different from earlier/different Arduino I2C LCD displays //Slaveaddress hardwired to 0x4E. SDA/SCL has pullup Resistors onboard. //See http://arduino-info.wikispaces.com/LCD-Blue-I2C // //Definitions for DFROBOT V1.1 //This hardware uses PCF8574. Slaveaddress may be set by jumpers (default 0x40). //SDA/SCL has pullup Resistors onboard and features a voltage level converter 3V3 <-> 5V. //See http://www.dfrobot.com/index.php?route=product/product&product_id=135 // // //Note: LCD RW pin must be kept LOW // E2 is not available on default Arduino hardware and so it does not support LCD40x4 (second controller) // BL is used to control backlight #define D_LCD_PIN_RS 0 #define D_LCD_PIN_RW 1 #define D_LCD_PIN_E 2 #define D_LCD_PIN_BL 3 #define D_LCD_PIN_D4 4 #define D_LCD_PIN_D5 5 #define D_LCD_PIN_D6 6 #define D_LCD_PIN_D7 7 #define D_LCD_PIN_E2 D_LCD_PIN_RW //Force I2C portexpander type #define PCF8574 1 #define MCP23008 0 //Inverted Backlight control #define BACKLIGHT_INV 0 #endif #if (YWROBOT==1) //Definitions for YWROBOT LCM1602 V1 Module mapping between serial port expander pins and LCD controller. //Very similar to DFROBOT. This hardware uses PCF8574. //Slaveaddress may be set by solderbridges (default 0x4E). SDA/SCL has no pullup Resistors onboard. //See http://arduino-info.wikispaces.com/LCD-Blue-I2C // //Note: LCD RW pin must be kept LOW // E2 is not available on default hardware and so it does not support LCD40x4 (second controller) // BL is used to control backlight, reverse logic: Low turns on Backlight. This is handled in setBacklight() #define D_LCD_PIN_RS 0 #define D_LCD_PIN_RW 1 #define D_LCD_PIN_E 2 #define D_LCD_PIN_BL 3 #define D_LCD_PIN_D4 4 #define D_LCD_PIN_D5 5 #define D_LCD_PIN_D6 6 #define D_LCD_PIN_D7 7 #define D_LCD_PIN_E2 D_LCD_PIN_RW //Force I2C portexpander type #define PCF8574 1 #define MCP23008 0 //Inverted Backlight control #define BACKLIGHT_INV 0 #endif #if (GYLCD==1) //Definitions for Arduino-IIC-LCD GY-LCD-V1 Module mapping between serial port expander pins and LCD controller. //Very similar to DFROBOT. This hardware uses PCF8574. //Slaveaddress may be set by solderbridges (default 0x4E). SDA/SCL has pullup Resistors onboard. //See http://arduino-info.wikispaces.com/LCD-Blue-I2C // //Note: LCD RW pin must be kept LOW // E2 is not available on default hardware and so it does not support LCD40x4 (second controller) // BL is used to control backlight, reverse logic: Low turns on Backlight. This is handled in setBacklight() #define D_LCD_PIN_D4 0 #define D_LCD_PIN_D5 1 #define D_LCD_PIN_D6 2 #define D_LCD_PIN_D7 3 #define D_LCD_PIN_EN 4 #define D_LCD_PIN_RW 5 #define D_LCD_PIN_RS 6 #define D_LCD_PIN_BL 7 #define D_LCD_PIN_E2 D_LCD_PIN_RW //Force I2C portexpander type #define PCF8574 1 #define MCP23008 0 //Force Inverted Backlight control #define BACKLIGHT_INV 1 #endif #if (SYDZ==1) //Definitions for SYDZ Module mapping between serial port expander pins and LCD controller. //Very similar to DFROBOT. This hardware uses PCF8574A and uses inverted Backlight control //Slaveaddress may be set by switches (default 0x40). SDA/SCL has pullup Resistors onboard. //See ebay // //Note: LCD RW pin must be kept LOW // E2 is not available on default hardware and so it does not support LCD40x4 (second controller) // BL is used to control backlight, reverse logic: Low turns on Backlight. This is handled in setBacklight() #define D_LCD_PIN_RS 0 #define D_LCD_PIN_RW 1 #define D_LCD_PIN_E 2 #define D_LCD_PIN_BL 3 #define D_LCD_PIN_D4 4 #define D_LCD_PIN_D5 5 #define D_LCD_PIN_D6 6 #define D_LCD_PIN_D7 7 #define D_LCD_PIN_E2 D_LCD_PIN_RW //Force I2C portexpander type #define PCF8574 1 #define MCP23008 0 //Force Inverted Backlight control #define BACKLIGHT_INV 1 #endif //Bitpattern Defines for I2C PCF8574/PCF8574A, MCP23008 and SPI 74595 Bus expanders // #define D_LCD_D4 (1<<D_LCD_PIN_D4) #define D_LCD_D5 (1<<D_LCD_PIN_D5) #define D_LCD_D6 (1<<D_LCD_PIN_D6) #define D_LCD_D7 (1<<D_LCD_PIN_D7) #define D_LCD_RS (1<<D_LCD_PIN_RS) #define D_LCD_E (1<<D_LCD_PIN_E) #define D_LCD_E2 (1<<D_LCD_PIN_E2) #define D_LCD_BL (1<<D_LCD_PIN_BL) //#define D_LCD_RW (1<<D_LCD_PIN_RW) #define D_LCD_BUS_MSK (D_LCD_D4 | D_LCD_D5 | D_LCD_D6 | D_LCD_D7) #define D_LCD_BUS_DEF 0x00 /* PCF8574/PCF8574A I2C portexpander slave address */ #define PCF8574_SA0 0x40 #define PCF8574_SA1 0x42 #define PCF8574_SA2 0x44 #define PCF8574_SA3 0x46 #define PCF8574_SA4 0x48 #define PCF8574_SA5 0x4A #define PCF8574_SA6 0x4C #define PCF8574_SA7 0x4E #define PCF8574A_SA0 0x70 #define PCF8574A_SA1 0x72 #define PCF8574A_SA2 0x74 #define PCF8574A_SA3 0x76 #define PCF8574A_SA4 0x78 #define PCF8574A_SA5 0x7A #define PCF8574A_SA6 0x7C #define PCF8574A_SA7 0x7E /* MCP23008 I2C portexpander slave address */ #define MCP23008_SA0 0x40 #define MCP23008_SA1 0x42 #define MCP23008_SA2 0x44 #define MCP23008_SA3 0x46 #define MCP23008_SA4 0x48 #define MCP23008_SA5 0x4A #define MCP23008_SA6 0x4C #define MCP23008_SA7 0x4E /* MCP23008 I2C portexpander internal registers */ #define IODIR 0x00 #define IPOL 0x01 #define GPINTEN 0x02 #define DEFVAL 0x03 #define INTCON 0x04 #define IOCON 0x05 #define GPPU 0x06 #define INTF 0x07 #define INTCAP 0x08 #define GPIO 0x09 #define OLAT 0x0A /* ST7032i I2C slave address */ #define ST7032_SA 0x7C /* ST7036i I2C slave address */ #define ST7036_SA0 0x78 #define ST7036_SA1 0x7A #define ST7036_SA2 0x7C #define ST7036_SA3 0x7E /* PCF21XX I2C slave address */ #define PCF21XX_SA0 0x74 #define PCF21XX_SA1 0x76 /* AIP31068 I2C slave address */ #define AIP31068_SA 0x7C /* SSD1803 I2C slave address */ #define SSD1803_SA0 0x78 #define SSD1803_SA1 0x7A /* US2066/SSD1311 I2C slave address */ #define US2066_SA0 0x78 #define US2066_SA1 0x7A /* AC780 I2C slave address */ #define AC780_SA0 0x78 #define AC780_SA1 0x7A #define AC780_SA2 0x7C #define AC780_SA3 0x7E //Some native I2C controllers dont support ACK. Set define to '0' to allow code to proceed even without ACK //#define LCD_I2C_ACK 0 #define LCD_I2C_ACK 1 // Contrast setting, 6 significant bits (only supported for controllers with extended features) // Voltage Multiplier setting, 2 or 3 significant bits (only supported for controllers with extended features) #define LCD_DEF_CONTRAST 0x20 //ST7032 EastRising ERC1602FS-4 display //Contrast setting 6 significant bits //Voltage Multiplier setting 3 significant bits #define LCD_ST7032_CONTRAST 0x18 #define LCD_ST7032_RAB 0x04 //ST7036 EA DOGM1603 display //Contrast setting 6 significant bits //Voltage Multiplier setting 3 significant bits #define LCD_ST7036_CONTRAST 0x28 #define LCD_ST7036_RAB 0x04 //SSD1803 EA DOGM204 display //Contrast setting 6 significant bits //Voltage Multiplier setting 3 significant bits #define LCD_SSD1_CONTRAST 0x28 #define LCD_SSD1_RAB 0x06 //US2066/SSD1311 EastRising ER-OLEDM2002-4 display //Contrast setting 8 significant bits, use 6 for compatibility #define LCD_US20_CONTRAST 0x3F //#define LCD_US20_CONTRAST 0x1F //PCF2113, PCF2119 display //Contrast setting 6 significant bits //Voltage Multiplier setting 2 significant bits #define LCD_PCF2_CONTRAST 0x20 #define LCD_PCF2_S12 0x02 //PT6314 VFD display //Contrast setting 2 significant bits, use 6 for compatibility #define LCD_PT63_CONTRAST 0x3F #endif //MBED_TEXTLCDCONFIG_H