Revision 1:19dd18051447, committed 2014-11-10

Comitter:

adarsh5723

Date:

Mon Nov 10 03:55:53 2014 +0000

Parent:

0:9898eeeb7143

Commit message:

Part of Homework 5.; Firmware for controlling the servo.

Changed in this revision

diff -r 9898eeeb7143 -r 19dd18051447 main.cpp
--- a/main.cpp	Fri Nov 07 04:08:42 2014 +0000
+++ b/main.cpp	Mon Nov 10 03:55:53 2014 +0000
@@ -3,43 +3,59 @@
 #include "mbed.h"
 #include "Servo.h"
 
+
+
+DigitalIn toggleSwitch(D3);
+AnalogIn ldr0(A5);
+PwmOut servoDriver(D2);
 Servo myservo(D2); //change digital pin here
-bool ServoLogic=true; 
-AnalogIn pin0(A0);
-AnalogIn pin1(A1);
-AnalogIn pin2(A2);
-AnalogIn pin3(A3);
-float photoresistors[4];
+
 #define  THRESHOLD .001
 int counter = 0;
 
+Serial pc(USBTX, USBRX);
 int main() {
-    myservo.calibrate(.0006, 75.0); 
+    //myservo.position(270.0f);
+    myservo.calibrate(.0006, 120.0); 
+    bool servoLogic = 0;
+    
     while(1){
+        
+        
+ #if 1
+        if (toggleSwitch == 1)
+        //if (ldr0.read() > 0.7)
+            servoLogic = 1;
+        else
+            servoLogic = 0;
         //recieve_data(ServoLogic);
-        if (ServoLogic)
+        if (servoLogic)
         {
-            float o = .1;
+            float o = 0.0;
             myservo = o;
         }
         else{
-            float f= 0.28;
+            float f= 1;
             myservo = f;
         }
-            
-        photoresistors[0] = pin0.read();
-        photoresistors[1] = pin1.read();
-        photoresistors[2] = pin2.read();
-        photoresistors[3] = pin3.read();
-        
-        for(int p=0; p<3; p += 1) 
-        {
-            if ((photoresistors[p]) < THRESHOLD)
-                counter=counter++;
-                //
-        }
-       
-        //send_data(counter)
+        printf("%f\n\r",ldr0.read());
+ #else
+#if 0
+   int pos = 0;
+   for(pos = 0; pos < 100; pos += 1)  // goes from 0 degrees to 180 degrees
+      {                                  // in steps of 1 degree
+        myservo = pos/100;             // tell servo to go to position in variable 'pos'
+        wait(0.015);                       // waits 15ms for the servo to reach the position
+      }
+    for(pos = 100; pos>=1; pos-=1)     // goes from 180 degrees to 0 degrees
+      {                               
+        myservo = pos/100;             // tell servo to go to position in variable 'pos'
+        wait(0.015);                       // waits 15ms for the servo to reach the position
+      }       
+#else
+     myservo = 2;
+#endif
+#endif
         wait(.2);
     }
 }