Dependencies:   X_NUCLEO_IKS01A1 driver_mbed_TH02 LoRaWAN-lib-v1_0_1 SX1272Lib mbed

Fork of LoRaWAN-SX1272-Application-Demo by Uttam Bhat

LoRaWAN-SX1272-Application Demo uses https://os.mbed.com/components/SX1272MB2xAS/ mbed component shield on a nucleo board platform to demonstrate a Class-A LoRaWAN device in the 915MHz ISM band for North American region. It uses the LoRaWAN-lib and SX1272Lib libraries.

Comissioning.h (LoRaWAN Network Configuration)

The end-device can be activated in one of the two ways:

Over the Air (OTA) activation can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_EUI (8 Bytes) : Fist 3 Bytes is the Organizationally Unique Identifier (OUI) followed by 5 bytes of unique ID. If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_APPLICATION_EUI (8 Bytes)
• LORAWAN_APPLICATION_KEY (or DEVKEY) (16 Bytes)

Activation by Personalization (ABP) can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_ADDRESS (4 Bytes) : If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_NWKSKEY (16 Bytes)
• LORAWAN_APPSKEY (16 Bytes)

Config.h (LoRaWAN Communication Parameters)

• Mode of Operation : Hybrid If the end-device needs to be configured to operate over 8-channels, then Hybrid Mode needs to be enabled

• Mode of Operation : Frequency Hop If the end-device needs to be configured to operate over 64-channels, then Hybrid Mode needs to be disabled

• Delay between successive JOIN REQUESTs : The delay between successive Join Requests (until the end-device joins the network) can be configured using the parameter OVER_THE_AIR_ACTIVATION_DUTYCYCLE

• Inter-Frame Delay : One can change the delay between each frame transmission using APP_TX_DUTYCYCLE It is advisable that APP_TX_DUTYCYCLE is greater than or equal to 3sec.

• Data Rate : The data rate can be configured as per LoRaWAN specification using the paramter LORAWAN_DEFAULT_DATARATE. The range of values are DR_0, DR_1, DR_2, DR_3 and DR_4

• Confirmed/Unconfirmed Messages : The uplink message or payload can be chosen to be confirmed or unconfirmed using the parameter LORAWAN_CONFIRMED_MSG_ON. When set to 1, the transmitted messages need to be confirmed with an ACK by the network server in the subsequent RX window. When set to 0, no ACK is requested.

• ADR ON/OFF : The ADR can be enabled or disabled using the parameter LORAWAN_ADR_ON. When set to 1, ADR is enabled and disabled when set to 0.

• Application Port : The application port can be set using parameter LORAWAN_APP_PORT. A few examples are associated to specific Application Port, and are defined in Config.h

• Payload Length : The lenght of the payload (in bytes) to be transmitted can be configured using LORAWAN_APP_DATA_SIZE

• Transmit Power : The transmit power can be configured using LORAWAN_TX_POWER (LoRaMAC verifies if the set power is compliant with the LoRaWAN spec and FCC guidelines)

The baud-rate for serial terminal display is 115200

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/app/Comissioning.h	Thu Apr 06 21:59:50 2017 +0000
@@ -0,0 +1,78 @@
+/*
+ / _____)             _              | |
+( (____  _____ ____ _| |_ _____  ____| |__
+ \____ \| ___ |    (_   _) ___ |/ ___)  _ \
+ _____) ) ____| | | || |_| ____( (___| | | |
+(______/|_____)_|_|_| \__)_____)\____)_| |_|
+    (C)2015 Semtech
+
+Description: End device comissioning parameters
+
+License: Revised BSD License, see LICENSE.TXT file include in the project
+
+Maintainer: Miguel Luis and Gregory Cristian
+*/
+#ifndef __LORA_COMISSIONING_H__
+#define __LORA_COMISSIONING_H__
+
+/*!
+ * When set to 1 the application uses the Over-the-Air activation procedure
+ * When set to 0 the application uses the Personalization activation procedure
+ */
+#define OVER_THE_AIR_ACTIVATION                     1
+
+/*!
+ * Indicates if the end-device is to be connected to a private or public network
+ */
+#define LORAWAN_PUBLIC_NETWORK                      true
+
+#if( OVER_THE_AIR_ACTIVATION != 0 )
+
+/*!
+ * Mote device IEEE OUI (big endian)
+ * \remark This is unique to a company or organization
+ */
+#define IEEE_OUI                                    0x00, 0x00, 0x00
+
+/*!
+ * Mote device IEEE EUI (big endian)
+ *
+ * \remark In this application, if the last 4 bytes are all 0, then the 32 bit address is automatically generated using a pseudo random generator seeded with a value derived from BoardUniqueId value
+ * If provided by user, e.g. { IEEE_OUI, 0x00, 0x00, 0x00, 0xFF, 0x01 }, then this value is used by the application
+ */
+#define LORAWAN_DEVICE_EUI                          { IEEE_OUI, 0x00, 0x00, 0x00, 0x00, 0x00 }
+
+/*!
+ * Application IEEE EUI (big endian)
+ */
+#define LORAWAN_APPLICATION_EUI                     { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }
+
+/*!
+ * AES encryption/decryption cipher application key
+ */
+#define LORAWAN_APPLICATION_KEY                     { 0x00, 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77, 0x88, 0x99, 0xaa, 0xbb, 0xcc, 0xdd, 0xee, 0xff }
+
+#else
+
+/*!
+ * Device address on the network (big endian)
+ *
+ * \remark In this application, if the value is 0, then the address is automatically generated using a pseudo random generator seeded with a value derived from BoardUniqueId value
+ * If provided by user, e.g. 0x78563412, then this value is used by the application
+ */
+#define LORAWAN_DEVICE_ADDRESS                      ( uint32_t )0x0
+
+/*!
+ * AES encryption/decryption cipher network session key
+ */
+#define LORAWAN_NWKSKEY                             { 0x2B, 0x7E, 0x15, 0x16, 0x28, 0xAE, 0xD2, 0xA6, 0xAB, 0xF7, 0x15, 0x88, 0x09, 0xCF, 0x4F, 0x3C }
+
+/*!
+ * AES encryption/decryption cipher application session key
+ */
+#define LORAWAN_APPSKEY                             { 0x2B, 0x7E, 0x15, 0x16, 0x28, 0xAE, 0xD2, 0xA6, 0xAB, 0xF7, 0x15, 0x88, 0x09, 0xCF, 0x4F, 0x3C }
+
+#endif
+
+
+#endif // __LORA_COMISSIONING_H__