File content as of revision 1:2105b8894450:

/**
  ******************************************************************************
  * @file    stm32l4r9i_discovery_ospi_nor.c
  * @author  MCD Application Team
  * @brief   This file includes a standard driver for the MX25LM51245G OSPI
  *          memory mounted on STM32L4R9I_DISCOVERY board.
  @verbatim
  ==============================================================================
                     ##### How to use this driver #####
  ==============================================================================
  [..]
   (#) This driver is used to drive the MX25LM51245G OSPI external
       memory mounted on STM32L4R9I_DISCOVERY evaluation board.

   (#) This driver need a specific component driver (MX25LM51245G) to be included with.

   (#) Initialization steps:
       (++) Initialize the OPSI external memory using the BSP_OSPI_NOR_Init() function. This
            function includes the MSP layer hardware resources initialization and the
            OSPI interface with the external memory.

   (#) OSPI memory operations
       (++) OSPI memory can be accessed with read/write operations once it is
            initialized.
            Read/write operation can be performed with AHB access using the functions
            BSP_OSPI_NOR_Read()/BSP_OSPI_NOR_Write().
       (++) The function BSP_OSPI_NOR_GetInfo() returns the configuration of the OSPI memory.
            (see the OSPI memory data sheet)
       (++) Perform erase block operation using the function BSP_OSPI_NOR_Erase_Block() and by
            specifying the block address. You can perform an erase operation of the whole
            chip by calling the function BSP_OSPI_NOR_Erase_Chip().
       (++) The function BSP_OSPI_NOR_GetStatus() returns the current status of the OSPI memory.
            (see the OSPI memory data sheet)
  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32l4r9i_discovery_ospi_nor.h"

/** @addtogroup BSP
  * @{
  */

/** @addtogroup STM32L4R9I_DISCOVERY
  * @{
  */

/** @defgroup STM32L4R9I_DISCOVERY_OSPI_NOR STM32L4R9I_DISCOVERY OSPI NOR
  * @{
  */

/* Private constants --------------------------------------------------------*/
/** @defgroup STM32L4R9I_DISCOVERY_OSPI_NOR_Private_Constants Private Constants
  * @{
  */
#define OSPI_NOR_OCTAL_DISABLE      0x0
#define OSPI_NOR_OCTAL_ENABLE       0x1

#define DUMMY_CYCLES_READ_OCTAL     MX25LM51245G_DUMMY_CYCLES_READ_OCTAL_66M
#define DUMMY_CYCLES_CR_CFG         MX25LM51245G_CR2_DC_66M
/**
  * @}
  */

/* Uncomment this line to use the memory in SDR mode */
//#define BSP_OSPI_NOR_DDR_MODE_DEACTIVATED

/* Private variables ---------------------------------------------------------*/

/** @defgroup STM32L4R9I_DISCOVERY_OSPI_NOR_Private_Variables Private Variables
  * @{
  */
OSPI_HandleTypeDef OSPINORHandle;

/**
  * @}
  */


/* Private functions ---------------------------------------------------------*/

/** @defgroup STM32L4R9I_DISCOVERY_OSPI_NOR_Private_Functions Private Functions
  * @{
  */
static void    OSPI_NOR_MspInit            (void);
static void    OSPI_NOR_MspDeInit          (void);
static uint8_t OSPI_NOR_ResetMemory        (OSPI_HandleTypeDef *hospi);
static uint8_t OSPI_NOR_WriteEnable        (OSPI_HandleTypeDef *hospi);
static uint8_t OSPI_NOR_AutoPollingMemReady(OSPI_HandleTypeDef *hospi, uint32_t Timeout);
static uint8_t OSPI_NOR_OctalMode          (OSPI_HandleTypeDef *hospi, uint8_t Operation);
/**
  * @}
  */

/* Exported functions ---------------------------------------------------------*/

/** @addtogroup STM32L4R9I_DISCOVERY_OSPI_NOR_Exported_Functions
  * @{
  */

/**
  * @brief  Initializes the OSPI interface.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_Init(void)
{
  OSPIM_CfgTypeDef OSPIM_Cfg_Struct;

  OSPINORHandle.Instance = OCTOSPI1;

  /* Call the DeInit function to reset the driver */
  if (HAL_OSPI_DeInit(&OSPINORHandle) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* System level initialization */
  OSPI_NOR_MspInit();

  /* OctoSPI initialization */
  OSPINORHandle.Init.FifoThreshold         = 4;
  OSPINORHandle.Init.DualQuad              = HAL_OSPI_DUALQUAD_DISABLE;
  OSPINORHandle.Init.DeviceSize            = POSITION_VAL(MX25LM51245G_FLASH_SIZE); /* 512 MBits */
  OSPINORHandle.Init.ChipSelectHighTime    = 2;
  OSPINORHandle.Init.FreeRunningClock      = HAL_OSPI_FREERUNCLK_DISABLE;
  OSPINORHandle.Init.ClockMode             = HAL_OSPI_CLOCK_MODE_0;
  OSPINORHandle.Init.WrapSize              = HAL_OSPI_WRAP_NOT_SUPPORTED;
  OSPINORHandle.Init.ClockPrescaler        = 2; /* OctoSPI clock = 120MHz / ClockPrescaler = 60MHz */
  OSPINORHandle.Init.SampleShifting        = HAL_OSPI_SAMPLE_SHIFTING_NONE;
#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  OSPINORHandle.Init.MemoryType            = HAL_OSPI_MEMTYPE_MICRON;
  OSPINORHandle.Init.DelayHoldQuarterCycle = HAL_OSPI_DHQC_DISABLE;
#else
  OSPINORHandle.Init.MemoryType            = HAL_OSPI_MEMTYPE_MACRONIX;
  OSPINORHandle.Init.DelayHoldQuarterCycle = HAL_OSPI_DHQC_ENABLE;
#endif
  OSPINORHandle.Init.ChipSelectBoundary    = 0;

  if (HAL_OSPI_Init(&OSPINORHandle) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* OctoSPI IO Manager configuration */
  OSPIM_Cfg_Struct.ClkPort    = 2;
  OSPIM_Cfg_Struct.DQSPort    = 2;
  OSPIM_Cfg_Struct.IOHighPort = HAL_OSPIM_IOPORT_2_HIGH;
  OSPIM_Cfg_Struct.IOLowPort  = HAL_OSPIM_IOPORT_2_LOW;
  OSPIM_Cfg_Struct.NCSPort    = 2;

  if (HAL_OSPIM_Config(&OSPINORHandle, &OSPIM_Cfg_Struct, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* OctoSPI memory reset */
  if (OSPI_NOR_ResetMemory(&OSPINORHandle) != OSPI_NOR_OK)
  {
    return OSPI_NOR_NOT_SUPPORTED;
  }

  /* Insert delay */
  HAL_Delay(1);

  /* OctoSPI octal enable */
  if (OSPI_NOR_OctalMode(&OSPINORHandle, OSPI_NOR_OCTAL_ENABLE) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  De-Initializes the OSPI interface.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_DeInit(void)
{
  OSPINORHandle.Instance = OCTOSPI1;

  /* Abort any activity on OctoSPI (eg Memory-mapped mode) */
  if (HAL_OSPI_GetState(&OSPINORHandle) != HAL_OSPI_STATE_READY)
  {
    if (HAL_OSPI_Abort(&OSPINORHandle) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }
  }

  /* OctoSPI octal mode disable */
  if (OSPI_NOR_OctalMode(&OSPINORHandle, OSPI_NOR_OCTAL_DISABLE) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Call the DeInit function to reset the driver */
  if (HAL_OSPI_DeInit(&OSPINORHandle) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* System level De-initialization */
  OSPI_NOR_MspDeInit();

  return OSPI_NOR_OK;
}

/**
  * @brief  Reads an amount of data from the OSPI memory.
  * @param  pData: Pointer to data to be read
  * @param  ReadAddr: Read start address
  * @param  Size: Size of data to read
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_Read(uint8_t* pData, uint32_t ReadAddr, uint32_t Size)
{
  OSPI_RegularCmdTypeDef sCommand;

  /* Initialize the read command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.Address               = ReadAddr;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize           = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_8_LINES;
  sCommand.NbData                = Size;
  sCommand.DummyCycles           = DUMMY_CYCLES_READ_OCTAL;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.Instruction           = OCTAL_IO_READ_CMD;
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_DISABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_DISABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
#else
  sCommand.Instruction           = OCTAL_IO_DTR_READ_CMD;
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_ENABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_ENABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_ENABLE;
#endif

  /* Configure the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Reception of the data */
  if (HAL_OSPI_Receive(&OSPINORHandle, pData, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  Writes an amount of data to the OSPI memory.
  * @param  pData: Pointer to data to be written
  * @param  WriteAddr: Write start address
  * @param  Size: Size of data to write
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_Write(uint8_t* pData, uint32_t WriteAddr, uint32_t Size)
{
  OSPI_RegularCmdTypeDef sCommand;
  uint32_t end_addr, current_size, current_addr;

  /* Calculation of the size between the write address and the end of the page */
  current_size = MX25LM51245G_PAGE_SIZE - (WriteAddr % MX25LM51245G_PAGE_SIZE);

  /* Check if the size of the data is less than the remaining place in the page */
  if (current_size > Size)
  {
    current_size = Size;
  }

  /* Initialize the adress variables */
  current_addr = WriteAddr;
  end_addr = WriteAddr + Size;

  /* Initialize the program command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_PAGE_PROG_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize           = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_8_LINES;
  sCommand.DummyCycles           = 0;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_DISABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_DISABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_ENABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_ENABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_ENABLE;
#endif

  /* Perform the write page by page */
  do
  {
    sCommand.Address = current_addr;
    sCommand.NbData  = current_size;

    /* Enable write operations */
    if (OSPI_NOR_WriteEnable(&OSPINORHandle) != OSPI_NOR_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Configure the command */
    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Transmission of the data */
    if (HAL_OSPI_Transmit(&OSPINORHandle, pData, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Configure automatic polling mode to wait for end of program */
    if (OSPI_NOR_AutoPollingMemReady(&OSPINORHandle, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != OSPI_NOR_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Update the address and size variables for next page programming */
    current_addr += current_size;
    pData += current_size;
    current_size = ((current_addr + MX25LM51245G_PAGE_SIZE) > end_addr) ? (end_addr - current_addr) : MX25LM51245G_PAGE_SIZE;
  } while (current_addr < end_addr);

  return OSPI_NOR_OK;
}

/**
  * @brief  Erases the specified block of the OSPI memory.
  * @param  BlockAddress: Block address to erase
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_Erase_Block(uint32_t BlockAddress)
{
  OSPI_RegularCmdTypeDef sCommand;

  /* Initialize the erase command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_BLOCK_ERASE_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.Address               = BlockAddress;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize           = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_NONE;
  sCommand.DummyCycles           = 0;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_ENABLE;
#endif

  /* Enable write operations */
  if (OSPI_NOR_WriteEnable(&OSPINORHandle) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Send the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Configure automatic polling mode to wait for end of erase */
  if (OSPI_NOR_AutoPollingMemReady(&OSPINORHandle, MX25LM51245G_BLOCK_ERASE_MAX_TIME) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  Erases the specified sector of the OSPI memory.
  * @param  Sector: Sector address to erase (0 to 255)
  * @retval OSPI memory status
  * @note This function is non blocking meaning that sector erase
  *       operation is started but not completed when the function
  *       returns. Application has to call BSP_QSPI_GetStatus()
  *       to know when the device is available again (i.e. erase operation
  *       completed).
  */
uint8_t BSP_OSPI_NOR_Erase_Sector(uint32_t Sector)
{
  OSPI_RegularCmdTypeDef sCommand;

  if (Sector >= (uint32_t)(MX25LM51245G_FLASH_SIZE/MX25LM51245G_SECTOR_SIZE))
  {
    return OSPI_NOR_ERROR;
  }

  /* Initialize the erase command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_SECTOR_ERASE_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.Address               = (Sector * MX25LM51245G_SECTOR_SIZE);
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize           = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_NONE;
  sCommand.DummyCycles           = 0;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_ENABLE;
#endif

  /* Enable write operations */
  if (OSPI_NOR_WriteEnable(&OSPINORHandle) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Send the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  Erases the entire OSPI memory.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_Erase_Chip(void)
{
  OSPI_RegularCmdTypeDef sCommand;

  /* Initialize the erase command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_CHIP_ERASE_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_NONE;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_NONE;
  sCommand.DummyCycles           = 0;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
#endif

  /* Enable write operations */
  if (OSPI_NOR_WriteEnable(&OSPINORHandle) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Send the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Configure automatic polling mode to wait for end of erase */
  if (OSPI_NOR_AutoPollingMemReady(&OSPINORHandle, MX25LM51245G_CHIP_ERASE_MAX_TIME) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  Reads current status of the OSPI memory.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_GetStatus(void)
{
  OSPI_RegularCmdTypeDef sCommand;
  uint8_t reg[2];

  /* Initialize the read security register command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_READ_SECURITY_REG_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.Address               = 0;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize           = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_8_LINES;
  sCommand.NbData                = 2;
  sCommand.DummyCycles           = DUMMY_CYCLES_READ_OCTAL;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_DISABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_DISABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_ENABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_ENABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_ENABLE;
#endif

  /* Configure the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Reception of the data */
  if (HAL_OSPI_Receive(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Check the value of the register */
  if ((reg[0] & (MX25LM51245G_SECR_P_FAIL | MX25LM51245G_SECR_E_FAIL)) != 0)
  {
    return OSPI_NOR_ERROR;
  }
  else if ((reg[0] & (MX25LM51245G_SECR_PSB | MX25LM51245G_SECR_ESB)) != 0)
  {
    return OSPI_NOR_SUSPENDED;
  }

  /* Initialize the read status register command */
  sCommand.Instruction = OCTAL_READ_STATUS_REG_CMD;

  /* Configure the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Reception of the data */
  if (HAL_OSPI_Receive(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Check the value of the register */
  if ((reg[0] & MX25LM51245G_SR_WIP) != 0)
  {
    return OSPI_NOR_BUSY;
  }
  else
  {
    return OSPI_NOR_OK;
  }
}

/**
  * @brief  Return the configuration of the OSPI memory.
  * @param  pInfo: pointer on the configuration structure
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_GetInfo(OSPI_NOR_Info* pInfo)
{
  /* Configure the structure with the memory configuration */
  pInfo->FlashSize          = MX25LM51245G_FLASH_SIZE;
  pInfo->EraseSectorSize    = MX25LM51245G_BLOCK_SIZE;
  pInfo->EraseSectorsNumber = (MX25LM51245G_FLASH_SIZE/MX25LM51245G_BLOCK_SIZE);
  pInfo->ProgPageSize       = MX25LM51245G_PAGE_SIZE;
  pInfo->ProgPagesNumber    = (MX25LM51245G_FLASH_SIZE/MX25LM51245G_PAGE_SIZE);

  return OSPI_NOR_OK;
}

/**
  * @brief  Configure the OSPI in memory-mapped mode
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_EnableMemoryMappedMode(void)
{
  OSPI_RegularCmdTypeDef   sCommand;
  OSPI_MemoryMappedTypeDef sMemMappedCfg;

  /* Enable write operations */
  if (OSPI_NOR_WriteEnable(&OSPINORHandle) != OSPI_NOR_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Configure the command for the read instruction */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_READ_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize           = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_8_LINES;
  sCommand.DummyCycles           = DUMMY_CYCLES_READ_OCTAL;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.Instruction           = OCTAL_IO_READ_CMD;
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_DISABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_DISABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
#else
  sCommand.Instruction           = OCTAL_IO_DTR_READ_CMD;
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_ENABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_ENABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_ENABLE;
#endif

  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Configure the command for the write instruction */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_WRITE_CFG;
  sCommand.Instruction           = OCTAL_PAGE_PROG_CMD;
  sCommand.DummyCycles           = 0;

  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

   /* Configure the memory mapped mode */
  sMemMappedCfg.TimeOutActivation = HAL_OSPI_TIMEOUT_COUNTER_DISABLE;

  if (HAL_OSPI_MemoryMapped(&OSPINORHandle, &sMemMappedCfg) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  This function suspends an ongoing erase command.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_SuspendErase(void)
{
  OSPI_RegularCmdTypeDef sCommand;

  /* Check whether the device is busy (erase operation is
  in progress).
  */
  if (BSP_OSPI_NOR_GetStatus() == OSPI_NOR_BUSY)
  {
    /* Initialize the suspend command */
    sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
    sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
    sCommand.Instruction           = OCTAL_PROG_ERASE_SUSPEND_CMD;
    sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
    sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
    sCommand.AddressMode           = HAL_OSPI_ADDRESS_NONE;
    sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
    sCommand.DataMode              = HAL_OSPI_DATA_NONE;
    sCommand.DummyCycles           = 0;
    sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
    sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
    sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
#else
    sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
#endif

  /* Send the command */
    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (BSP_OSPI_NOR_GetStatus() == OSPI_NOR_SUSPENDED)
    {
      return OSPI_NOR_OK;
    }

    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  This function resumes a paused erase command.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_ResumeErase(void)
{
  OSPI_RegularCmdTypeDef sCommand;

  /* Check whether the device is in suspended state */
  if (BSP_OSPI_NOR_GetStatus() == OSPI_NOR_SUSPENDED)
  {
    /* Initialize the resume command */
    sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
    sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
    sCommand.Instruction           = OCTAL_PROG_ERASE_RESUME_CMD;
    sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
    sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
    sCommand.AddressMode           = HAL_OSPI_ADDRESS_NONE;
    sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
    sCommand.DataMode              = HAL_OSPI_DATA_NONE;
    sCommand.DummyCycles           = 0;
    sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
    sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
    sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
#else
    sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
#endif

    /* Send the command */
    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /*
    When this command is executed, the status register write in progress bit is set to 1, and
    the flag status register program erase controller bit is set to 0. This command is ignored
    if the device is not in a suspended state.
    */

    if (BSP_OSPI_NOR_GetStatus() == OSPI_NOR_BUSY)
    {
      return OSPI_NOR_OK;
    }

    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  This function enter the OSPI memory in deep power down mode.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_EnterDeepPowerDown(void)
{
  OSPI_RegularCmdTypeDef sCommand;

  /* Initialize the deep power down command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_ENTER_DEEP_POWER_DOWN_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_NONE;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_NONE;
  sCommand.DummyCycles           = 0;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
#endif

  /* Send the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* ---          Memory takes 10us max to enter deep power down          --- */

  return OSPI_NOR_OK;
}

/**
  * @brief  This function leave the OSPI memory from deep power down mode.
  * @retval OSPI memory status
  */
uint8_t BSP_OSPI_NOR_LeaveDeepPowerDown(void)
{
  OSPI_RegularCmdTypeDef sCommand;

  /* Initialize the nop command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_NO_OPERATION_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_NONE;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_NONE;
  sCommand.DummyCycles           = 0;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
#endif

  /* Send the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* --- A NOP command is sent to the memory, as the nCS should be low for at least 20 ns --- */
  /* ---                  Memory takes 30us min to leave deep power down                  --- */

  return OSPI_NOR_OK;
}
/**
  * @}
  */

/** @addtogroup STM32L4R9I_DISCOVERY_OSPI_NOR_Private_Functions
  * @{
  */

/**
  * @brief  Initializes the OSPI MSP.
  * @retval None
  */
static void OSPI_NOR_MspInit(void)
{
  GPIO_InitTypeDef GPIO_InitStruct;

  /* Enable the OctoSPI memory interface clock */
  __HAL_RCC_OSPIM_CLK_ENABLE();
  __HAL_RCC_OSPI1_CLK_ENABLE();

  /* Reset the OctoSPI memory interface */
  __HAL_RCC_OSPI1_FORCE_RESET();
  __HAL_RCC_OSPI1_RELEASE_RESET();

  /* Enable GPIO clocks */
  /* IOSV bit MUST be set to access GPIO port G[2:15] */
  __HAL_RCC_PWR_CLK_ENABLE();
  SET_BIT(PWR->CR2, PWR_CR2_IOSV);

  __HAL_RCC_GPIOG_CLK_ENABLE();
  __HAL_RCC_GPIOH_CLK_ENABLE();
  __HAL_RCC_GPIOI_CLK_ENABLE();

  /* OctoSPI CS GPIO pin configuration  */
  GPIO_InitStruct.Pin       = GPIO_PIN_12;
  GPIO_InitStruct.Mode      = GPIO_MODE_AF_PP;
  GPIO_InitStruct.Pull      = GPIO_PULLUP;
  GPIO_InitStruct.Speed     = GPIO_SPEED_FREQ_VERY_HIGH;
  GPIO_InitStruct.Alternate = GPIO_AF5_OCTOSPIM_P2;
  HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);

  /* OctoSPI DQS GPIO pins configuration  */
  GPIO_InitStruct.Pin       = GPIO_PIN_15;
  HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);

  /* OctoSPI CLK, D0, D1 and D2 GPIO pins configuration  */
  GPIO_InitStruct.Pin       = (GPIO_PIN_6 | GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11);
  GPIO_InitStruct.Pull      = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);

  /* OctoSPI D3, D4 and D5 GPIO pins configuration  */
  GPIO_InitStruct.Pin       = (GPIO_PIN_8 | GPIO_PIN_9 | GPIO_PIN_10);
  HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);

  /* OctoSPI D6 and D7 GPIO pins configuration  */
  GPIO_InitStruct.Pin       = (GPIO_PIN_9 | GPIO_PIN_10);
  HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);
}

/**
  * @brief  De-Initializes the OSPI MSP.
  * @retval None
  */
static void OSPI_NOR_MspDeInit(void)
{
  GPIO_InitTypeDef GPIO_InitStruct;

  /* OctoSPI CLK, CS, D0-D7, DQS GPIO pins de-configuration  */
  HAL_GPIO_DeInit(GPIOG, (GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_12 | GPIO_PIN_15));
  HAL_GPIO_DeInit(GPIOH, (GPIO_PIN_8 | GPIO_PIN_9 | GPIO_PIN_10));
  HAL_GPIO_DeInit(GPIOI, (GPIO_PIN_6 | GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11));

  /* Set GPIOG pin 12 in pull up mode (optimum default setting) */
  GPIO_InitStruct.Mode      = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pin       = GPIO_PIN_12;
  GPIO_InitStruct.Pull      = GPIO_NOPULL;
  GPIO_InitStruct.Speed     = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);

  /* Set GPIOG pin 15 in no pull, low state (optimum default setting) */
  GPIO_InitStruct.Mode      = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull      = GPIO_NOPULL;
  GPIO_InitStruct.Pin       = GPIO_PIN_15;
  HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);
  HAL_GPIO_WritePin(GPIOG, GPIO_PIN_15, GPIO_PIN_RESET);

  /* Reset the OctoSPI memory interface */
  __HAL_RCC_OSPI1_FORCE_RESET();
  __HAL_RCC_OSPI1_RELEASE_RESET();

  /* Disable the OctoSPI memory interface clock */
  __HAL_RCC_OSPI1_CLK_DISABLE();
}

/**
  * @brief  This function reset the OSPI memory.
  * @param  hospi: OSPI handle
  * @retval None
  */
static uint8_t OSPI_NOR_ResetMemory(OSPI_HandleTypeDef *hospi)
{
  OSPI_RegularCmdTypeDef sCommand;
  OSPI_AutoPollingTypeDef sConfig;

  /* Initialize the reset enable command */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = RESET_ENABLE_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_1_LINE;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_8_BITS;
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_NONE;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_NONE;
  sCommand.DummyCycles           = 0;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

  /* Send the command */
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Send the reset memory command */
  sCommand.Instruction = RESET_MEMORY_CMD;
  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Configure automatic polling mode to wait the memory is ready */
  sCommand.Instruction  = READ_STATUS_REG_CMD;
  sCommand.DataMode     = HAL_OSPI_DATA_1_LINE;
  sCommand.NbData       = 1;
  sCommand.DataDtrMode  = HAL_OSPI_DATA_DTR_DISABLE;

  sConfig.Match         = 0;
  sConfig.Mask          = MX25LM51245G_SR_WIP;
  sConfig.MatchMode     = HAL_OSPI_MATCH_MODE_AND;
  sConfig.Interval      = 0x10;
  sConfig.AutomaticStop = HAL_OSPI_AUTOMATIC_STOP_ENABLE;

  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  if (HAL_OSPI_AutoPolling(&OSPINORHandle, &sConfig, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  return OSPI_NOR_OK;
}

/**
  * @brief  This function send a Write Enable and wait it is effective.
  * @param  hospi: OSPI handle
  * @retval None
  */
static uint8_t OSPI_NOR_WriteEnable(OSPI_HandleTypeDef *hospi)
{
  OSPI_RegularCmdTypeDef  sCommand;
  OSPI_AutoPollingTypeDef sConfig;
  uint8_t reg[2];

  /* Enable write operations */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_WRITE_ENABLE_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_NONE;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_NONE;
  sCommand.DummyCycles           = 0;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
#endif

  if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
  {
    return OSPI_NOR_ERROR;
  }

  /* Configure automatic polling mode to wait for write enabling */
  sConfig.Match           = MX25LM51245G_SR_WEL;
  sConfig.Mask            = MX25LM51245G_SR_WEL;

  sCommand.Instruction    = OCTAL_READ_STATUS_REG_CMD;
  sCommand.Address        = 0x0;
  sCommand.AddressMode    = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize    = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.DataMode       = HAL_OSPI_DATA_8_LINES;
  sCommand.NbData         = 2;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.AddressDtrMode = HAL_OSPI_ADDRESS_DTR_DISABLE;
  sCommand.DataDtrMode    = HAL_OSPI_DATA_DTR_DISABLE;
  sCommand.DQSMode        = HAL_OSPI_DQS_DISABLE;
  sCommand.DummyCycles    = DUMMY_CYCLES_READ_OCTAL;
#else
  sCommand.AddressDtrMode = HAL_OSPI_ADDRESS_DTR_ENABLE;
  sCommand.DataDtrMode    = HAL_OSPI_DATA_DTR_ENABLE;
  sCommand.DQSMode        = HAL_OSPI_DQS_ENABLE;
  sCommand.DummyCycles    = 4;
#endif

  do
  {
    HAL_Delay(1); /* sConfig.Interval(0x10) / Clock(55 MHz) = 0.29 ms */

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_Receive(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }
  }while((reg[0] & sConfig.Mask ) != sConfig.Match);

  return OSPI_NOR_OK;
}

/**
  * @brief  This function read the SR of the memory and wait the EOP.
  * @param  hospi: OSPI handle
  * @param  Timeout: Timeout for auto-polling
  * @retval None
  */
static uint8_t OSPI_NOR_AutoPollingMemReady(OSPI_HandleTypeDef *hospi, uint32_t Timeout)
{
  OSPI_RegularCmdTypeDef  sCommand;
  OSPI_AutoPollingTypeDef sConfig;
  uint8_t reg[2];

  /* Configure automatic polling mode to wait for memory ready */
  sCommand.OperationType         = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId               = HAL_OSPI_FLASH_ID_1;
  sCommand.Instruction           = OCTAL_READ_STATUS_REG_CMD;
  sCommand.InstructionMode       = HAL_OSPI_INSTRUCTION_8_LINES;
  sCommand.InstructionSize       = HAL_OSPI_INSTRUCTION_16_BITS;
  sCommand.Address               = 0;
  sCommand.AddressMode           = HAL_OSPI_ADDRESS_8_LINES;
  sCommand.AddressSize           = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AlternateBytesMode    = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataMode              = HAL_OSPI_DATA_8_LINES;
  sCommand.NbData                = 2;
  sCommand.DummyCycles           = DUMMY_CYCLES_READ_OCTAL;
  sCommand.SIOOMode              = HAL_OSPI_SIOO_INST_EVERY_CMD;

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_DISABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_DISABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_DISABLE;
#else
  sCommand.InstructionDtrMode    = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
  sCommand.AddressDtrMode        = HAL_OSPI_ADDRESS_DTR_ENABLE;
  sCommand.DataDtrMode           = HAL_OSPI_DATA_DTR_ENABLE;
  sCommand.DQSMode               = HAL_OSPI_DQS_ENABLE;
#endif

  sConfig.Match           = 0;
  sConfig.Mask            = MX25LM51245G_SR_WIP;

  do
  {
    HAL_Delay(1); /* sConfig.Interval(0x10) / Clock(55 MHz) = 0.29 ms */

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_Receive(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }
  }while((reg[0] & sConfig.Mask ) != sConfig.Match);

  return OSPI_NOR_OK;
}

/**
  * @brief  This function enables/disables the octal mode of the memory.
  * @param  hospi: OSPI handle
  * @param  Operation: Octal operation mode enable/disable
  * @retval None
  */
static uint8_t OSPI_NOR_OctalMode(OSPI_HandleTypeDef *hospi, uint8_t Operation)
{
  OSPI_RegularCmdTypeDef  sCommand;
  OSPI_AutoPollingTypeDef sConfig;
  uint8_t reg[2];

  sCommand.OperationType      = HAL_OSPI_OPTYPE_COMMON_CFG;
  sCommand.FlashId            = HAL_OSPI_FLASH_ID_1;
  sCommand.InstructionDtrMode = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
  sCommand.AddressSize        = HAL_OSPI_ADDRESS_32_BITS;
  sCommand.AddressDtrMode     = HAL_OSPI_ADDRESS_DTR_DISABLE;
  sCommand.AlternateBytesMode = HAL_OSPI_ALTERNATE_BYTES_NONE;
  sCommand.DataDtrMode        = HAL_OSPI_DATA_DTR_DISABLE;
  sCommand.DQSMode            = HAL_OSPI_DQS_DISABLE;
  sCommand.SIOOMode           = HAL_OSPI_SIOO_INST_EVERY_CMD;

  sConfig.MatchMode     = HAL_OSPI_MATCH_MODE_AND;
  sConfig.Interval      = 0x10;
  sConfig.AutomaticStop = HAL_OSPI_AUTOMATIC_STOP_ENABLE;

  /* Activate/deactivate the Octal mode */
  if (Operation == OSPI_NOR_OCTAL_ENABLE)
  {
    /* Enable write operations */
    sCommand.Instruction     = WRITE_ENABLE_CMD;
    sCommand.InstructionMode = HAL_OSPI_INSTRUCTION_1_LINE;
    sCommand.InstructionSize = HAL_OSPI_INSTRUCTION_8_BITS;
    sCommand.AddressMode     = HAL_OSPI_ADDRESS_NONE;
    sCommand.DataMode        = HAL_OSPI_DATA_NONE;
    sCommand.DummyCycles     = 0;

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Configure automatic polling mode to wait for write enabling */
    sConfig.Match = MX25LM51245G_SR_WEL;
    sConfig.Mask  = MX25LM51245G_SR_WEL;

    sCommand.Instruction = READ_STATUS_REG_CMD;
    sCommand.DataMode    = HAL_OSPI_DATA_1_LINE;
    sCommand.NbData      = 1;

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_AutoPolling(&OSPINORHandle, &sConfig, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Write Configuration register 2 (with new dummy cycles) */
    sCommand.Instruction = WRITE_CFG_REG_2_CMD;
    sCommand.Address     = MX25LM51245G_CR2_REG3_ADDR;
    sCommand.AddressMode = HAL_OSPI_ADDRESS_1_LINE;
    reg[0] = DUMMY_CYCLES_CR_CFG;

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_Transmit(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Enable write operations */
    sCommand.Instruction = WRITE_ENABLE_CMD;
    sCommand.AddressMode = HAL_OSPI_ADDRESS_NONE;
    sCommand.DataMode    = HAL_OSPI_DATA_NONE;

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Configure automatic polling mode to wait for write enabling */
    sCommand.Instruction = READ_STATUS_REG_CMD;
    sCommand.DataMode    = HAL_OSPI_DATA_1_LINE;

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_AutoPolling(&OSPINORHandle, &sConfig, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Write Configuration register 2 (with Octal I/O SPI protocol) */
    sCommand.Instruction = WRITE_CFG_REG_2_CMD;
    sCommand.Address     = MX25LM51245G_CR2_REG1_ADDR;
    sCommand.AddressMode = HAL_OSPI_ADDRESS_1_LINE;
#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
    reg[0] = MX25LM51245G_CR2_SOPI;
#else
    reg[0] = MX25LM51245G_CR2_DOPI;
#endif

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_Transmit(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Wait that the configuration is effective and check that memory is ready */
    HAL_Delay(MX25LM51245G_WRITE_REG_MAX_TIME);

    if (OSPI_NOR_AutoPollingMemReady(&OSPINORHandle, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != OSPI_NOR_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Check the configuration has been correctly done */
    sCommand.Instruction     = OCTAL_READ_CFG_REG_2_CMD;
    sCommand.InstructionMode = HAL_OSPI_INSTRUCTION_8_LINES;
    sCommand.InstructionSize = HAL_OSPI_INSTRUCTION_16_BITS;
    sCommand.AddressMode     = HAL_OSPI_ADDRESS_8_LINES;
    sCommand.DataMode        = HAL_OSPI_DATA_8_LINES;
    sCommand.DummyCycles     = DUMMY_CYCLES_READ_OCTAL;
    sCommand.NbData          = 2;
    reg[0] = 0;

#if !defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
    sCommand.InstructionDtrMode = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
    sCommand.AddressDtrMode     = HAL_OSPI_ADDRESS_DTR_ENABLE;
    sCommand.DataDtrMode        = HAL_OSPI_DATA_DTR_ENABLE;
    sCommand.DQSMode            = HAL_OSPI_DQS_ENABLE;
#endif

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_Receive(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

#if defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
    if (reg[0] != MX25LM51245G_CR2_SOPI)
#else
    if (reg[0] != MX25LM51245G_CR2_DOPI)
#endif
    {
      return OSPI_NOR_ERROR;
    }
  }
  else
  {
    /* Enable write operations */
    if (OSPI_NOR_WriteEnable(&OSPINORHandle) != OSPI_NOR_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Write Configuration register 2 (with Octal I/O SPI protocol) */
    sCommand.Instruction     = OCTAL_WRITE_CFG_REG_2_CMD;
    sCommand.InstructionMode = HAL_OSPI_INSTRUCTION_8_LINES;
    sCommand.InstructionSize = HAL_OSPI_INSTRUCTION_16_BITS;
    sCommand.Address         = MX25LM51245G_CR2_REG1_ADDR;
    sCommand.AddressMode     = HAL_OSPI_ADDRESS_8_LINES;
    sCommand.DataMode        = HAL_OSPI_DATA_8_LINES;
    sCommand.NbData          = 2;
    sCommand.DummyCycles     = 0;
    reg[0] = 0;
    reg[1] = 0;

#if !defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
    sCommand.InstructionDtrMode = HAL_OSPI_INSTRUCTION_DTR_ENABLE;
    sCommand.AddressDtrMode     = HAL_OSPI_ADDRESS_DTR_ENABLE;
    sCommand.DataDtrMode        = HAL_OSPI_DATA_DTR_ENABLE;
#endif

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_Transmit(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Wait that the configuration is effective and check that memory is ready */
    HAL_Delay(MX25LM51245G_WRITE_REG_MAX_TIME);

    sCommand.Instruction     = READ_STATUS_REG_CMD;
    sCommand.InstructionMode = HAL_OSPI_INSTRUCTION_1_LINE;
    sCommand.InstructionSize = HAL_OSPI_INSTRUCTION_8_BITS;
    sCommand.AddressMode     = HAL_OSPI_ADDRESS_NONE;
    sCommand.DataMode        = HAL_OSPI_DATA_1_LINE;
    sCommand.NbData          = 1;
    sCommand.DummyCycles     = 0;

#if !defined BSP_OSPI_NOR_DDR_MODE_DEACTIVATED
    sCommand.InstructionDtrMode = HAL_OSPI_INSTRUCTION_DTR_DISABLE;
    sCommand.AddressDtrMode     = HAL_OSPI_ADDRESS_DTR_DISABLE;
    sCommand.DataDtrMode        = HAL_OSPI_DATA_DTR_DISABLE;
#endif

    sConfig.Match = 0;
    sConfig.Mask  = MX25LM51245G_SR_WIP;

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_AutoPolling(&OSPINORHandle, &sConfig, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    /* Check the configuration has been correctly done */
    sCommand.Instruction = READ_CFG_REG_2_CMD;
    sCommand.Address     = MX25LM51245G_CR2_REG1_ADDR;
    sCommand.AddressMode = HAL_OSPI_ADDRESS_1_LINE;

    if (HAL_OSPI_Command(&OSPINORHandle, &sCommand, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (HAL_OSPI_Receive(&OSPINORHandle, reg, HAL_OSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
    {
      return OSPI_NOR_ERROR;
    }

    if (reg[0] != 0)
    {
      return OSPI_NOR_ERROR;
    }
  }

  return OSPI_NOR_OK;
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/