ST Expansion SW Team / Mbed OS mbed-os-nfc05a1

Example application for the STMicroelectronics X-NUCLEO-NFC05A1

Dependencies:   RFAL ST25R3911 BSP05

X-NUCLEO-NFC05A1 NFC Card Reader Expansion Board Firmware Package

Introduction

This firmware package includes Components Device Drivers, Board Support Package and example applications for STMicroelectronics X-NUCLEO-NFC05A1 NFC Card Reader Expansion Board based on the ST25R3911B.

Example Application

This program gives the user the possibility to read the URI information written on the expansion board. The LEDs will blink for few seconds to indicate that the board is initializing. As soon as it finishes, the device is ready to communicate with external NFC devices. LED6 will blink until an NFC device is close to it and ready to read the URI value.

Tested Platforms

This firmware has been tested on STM32 NUCLEO-F401RE

source/logger.h

Committer:
DiegoOstuni
Date:
2019-11-14
Revision:
3:9a152c93d7a2
Parent:
1:86504e1ac6b1

File content as of revision 3:9a152c93d7a2:

/******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2016 STMicroelectronics</center></h2>
  *
  * Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/myliberty
  *
  * Unless required by applicable law or agreed to in writing, software
  * distributed under the License is distributed on an "AS IS" BASIS,
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
  * AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
  * FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
******************************************************************************/
/*
 *      PROJECT:
 *      $Revision: $
 *      LANGUAGE:  ANSI C
 */

/*! \file
 *
 *  \author
 *
 *  \brief serial output log declaration file
 *
 */
/*!
 *
 * This driver provides a printf-like way to output log messages
 * via the UART interface. It makes use of the uart driver.
 *
 * API:
 * - Write a log message to UART output: #DEBUG
 */

#ifndef LOGGER_H
#define LOGGER_H

/*
******************************************************************************
* INCLUDES
******************************************************************************
*/
#include "platform1.h"

/*
******************************************************************************
* DEFINES
******************************************************************************
*/
#define LOGGER_ON   1
#define LOGGER_OFF  0

/*!
 *****************************************************************************
 *  \brief  Writes out a formated string via UART interface
 *
 *  This function is used to write a formated string via the UART interface.
 *
 *****************************************************************************
 */
extern void logUsartInit(UART_HandleTypeDef *husart);

/*!
 *****************************************************************************
 *  \brief  Writes out a formated string via UART interface
 *
 *  This function is used to write a formated string via the UART interface.
 *
 *****************************************************************************
 */
extern int logUsart(const char* format, ...);

/*!
 *****************************************************************************
 *  \brief  helper to convert hex data into formated string
 *
 *  \param[in] data : pointer to buffer to be dumped.
 *
 *  \param[in] dataLen : buffer length
 *
 *  \return hex formated string
 *
 *****************************************************************************
 */
extern char* hex2Str(unsigned char * data, size_t dataLen);

#endif /* LOGGER_H */