File content as of revision 15:7620a11149b8:

#pragma once

// Authors: Ashley Mills, Nicholas Herriot
/* Copyright (c) 2013 Vodafone, MIT License
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy of this software
 * and associated documentation files (the "Software"), to deal in the Software without restriction,
 * including without limitation the rights to use, copy, modify, merge, publish, distribute,
 * sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in all copies or
 * substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
 * BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
 * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
 */

// the SparkFun breakout board defaults to 1, set to 0 if SA0 jumper on the bottom of the board is set
// see the Table 10. I2C Device Address Sequence in Freescale MMA8452Q pdf


#define DBG(...) pc.printf(__VA_ARGS__); pc.printf("\r\n");
#define DBGX(...) pc.print(__VA_ARGS__);
 
#include "mbed.h" 

// More info on MCU Master address can be found on section 5.10.1 of http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MMA8452Q
#define SA0 1
#if SA0
  #define MMA8452_ADDRESS 0x3A // 0x1D<<1  // SA0 is high, 0x1C if low - 
#else
  #define MMA8452_ADDRESS 0x38 // 0x1C<<1
#endif

// Register descriptions found in section 6 of pdf
#define MMA8452_STATUS 0x00                 // Type 'read' : Status of the data registers
#define MMA8452_OUT_X_MSB 0x01              // Type 'read' : x axis - MSB of 2 byte sample
#define MMA8452_OUT_X_LSB 0x02              // Type 'read' : x axis - LSB of 2 byte sample
#define MMA8452_OUT_Y_MSB 0x03              // Type 'read' : y axis - MSB of 2 byte sample
#define MMA8452_OUT_Y_LSB 0x04              // Type 'read' : y axis - LSB of 2 byte sample
#define MMA8452_OUT_Z_MSB 0x05              // Type 'read' : z axis - MSB of 2 byte sample
#define MMA8452_OUT_Z_LSB 0x06              // Type 'read' : z axis - LSB of 2 byte sample

// register definitions
#define MMA8452_XYZ_DATA_CFG 0x0E

#define MMA8452_SYSMOD 0x0B                         // Type 'read' : This tells you if device is active, sleep or standy 0x00=STANDBY 0x01=WAKE 0x02=SLEEP
#define MMA8452_WHO_AM_I 0x0D                       // Type 'read' : This should return the device id of 0x2A

#define MMA8452_PL_STATUS 0x10                      // Type 'read' : This shows portrait landscape mode orientation
#define MMA8452_PL_CFG 0x11                         // Type 'read/write' : This allows portrait landscape configuration
#define MMA8452_PL_COUNT 0x12                       // Type 'read' : This is the portraint landscape debounce counter
#define MMA8452_PL_BF_ZCOMP 0x13                    // Type 'read' :
#define MMA8452_PL_THS_REG 0x14                     // Type 'read' :

#define MMA8452_FF_MT_CFG 0X15                      // Type 'read/write' : Freefaul motion functional block configuration
#define MMA8452_FF_MT_SRC 0X16                      // Type 'read' : Freefaul motion event source register
#define MMA8452_FF_MT_THS 0X17                      // Type 'read' : Freefaul motion threshold register
#define MMA8452_FF_COUNT 0X18                       // Type 'read' : Freefaul motion debouce counter

#define MMA8452_ASLP_COUNT 0x29                     // Type 'read/write' : Counter settings for auto sleep
#define MMA8452_CTRL_REG_1 0x2A                     // Type 'read/write' :
#define MMA8452_CTRL_REG_2 0x2B                     // Type 'read/write' :
#define MMA8452_CTRL_REG_3 0x2C                     // Type 'read/write' :
#define MMA8452_CTRL_REG_4 0x2D                     // Type 'read/write' :
#define MMA8452_CTRL_REG_5 0x2E                     // Type 'read/write' :

// Defined in table 13 of the Freescale PDF
/// xxx these all need to have better names
#define STANDBY 0x00                        // State value returned after a SYSMOD request, it can be in state STANDBY, WAKE or SLEEP
#define WAKE 0x01                           // State value returned after a SYSMOD request, it can be in state STANDBY, WAKE or SLEEP
#define SLEEP 0x02                          // State value returned after a SYSMOD request, it can be in state STANDBY, WAKE or SLEEP
#define ACTIVE 0x01                         // Stage value returned and set in Control Register 1, it can be STANDBY=00, or ACTIVE=01
 
#define TILT_STATUS 0x03        // Tilt Status (Read only)
#define SRST_STATUS 0x04        // Sample Rate Status Register (Read only)
#define SPCNT_STATUS 0x05       // Sleep Count Register (Read/Write)
#define INTSU_STATUS 0x06       // Interrupt Setup Register
#define MODE_STATUS 0x07        // Mode Register (Read/Write)
#define SR_STATUS 0x08          // Auto-Wake and Active Mode Portrait/Landscape Samples per Seconds Register (Read/Write)
#define PDET_STATUS 0x09        // Tap/Pulse Detection Register (Read/Write)
#define PD_STATUS 0xA           // Tap/Pulse Debounce Count Register (Read/Write)
 
// masks for enabling/disabling standby
#define MMA8452_ACTIVE_MASK 0x01
#define MMA8452_STANDBY_MASK 0xFE

// mask for dynamic range reading and writing
#define MMA8452_DYNAMIC_RANGE_MASK 0xFC

// mask and shift for data rate reading and writing
#define MMA8452_DATA_RATE_MASK 0xC7
#define MMA8452_DATA_RATE_MASK_SHIFT 0x03

// mask and shift for general reading and writing
#define MMA8452_WRITE_MASK 0xFE
#define MMA8452_READ_MASK 0x01

// mask and shift for bit depth reading and writing
#define MMA8452_BIT_DEPTH_MASK 0xFD
#define MMA8452_BIT_DEPTH_MASK_SHIFT 0x01

// status masks and shifts
#define MMA8452_STATUS_ZYXDR_MASK 0x08
 
class MMA8452         
{        
    public:
    
       enum DynamicRange {
           DYNAMIC_RANGE_2G=0x00,
           DYNAMIC_RANGE_4G,
           DYNAMIC_RANGE_8G,
           DYNAMIC_RANGE_UNKNOWN
       };
        
       enum BitDepth {
           BIT_DEPTH_12=0x00,
           BIT_DEPTH_8, // 1 sets fast read mode, hence the inversion
           BIT_DEPTH_UNKNOWN
       };
       
       enum DataRateHz {
          RATE_800=0x00,
          RATE_400,
          RATE_200,
          RATE_100,
          RATE_50,
          RATE_12_5,
          RATE_6_25,
          RATE_1_563,
          RATE_UNKNOWN
       };
       
        
       /**
        * Create an accelerometer object connected to the specified I2C pins.
        *
        * @param sda I2C data port
        * @param scl I2C clock port
        * @param frequency 
        * 
        */ 
      MMA8452(PinName sda, PinName scl, int frequency);
       
      /// Destructor
      ~MMA8452();
      
      /**
       * Puts the MMA8452 in active mode.
       * @return 0 on success, 1 on failure.
       */
      int activate();
 
      /**
       * Puts the MMA8452 in standby.
       * @return 0 on success, 1 on failure.
       */
      int standby();      
      
       /** Initialization of device MMA8452 (required)
        */
      void init();
    
       /**
        * Read the device ID from the accelerometer (should be 0x2a)
        *
        * @param pointer to store the ID
        * @return 0 on success, 1 on failure.
        */        
      int getDeviceID(char* dst);  
      
      int getStatus(char* dst);  
      
      /** 
       * Read the x,y, and z registers of the MMA8452.
       *
       * @param dst The destination buffer. Note that this needs to be 3 bytes for
       * BIT_DEPTH_8 and 6 bytes for BIT_DEPTH_12. It is upto the caller to ensure this.
       * @return 0 for success, and 1 for failure
       */ 
      int readXYZRaw(char *dst);
      
      /**
       * Read the x,y, and z counts of the MMA7452.
       */
      int readXYZCounts(int *x, int *y, int *z);
      int readXYZGravity(double *x, double *y, double *z);
      
      int isXReady();
      int isYReady();
      int isZReady();
      int isXYZReady();
            
      /** 
       * Read from specified MMA8452 register.
       *
       * @param addr The internal registeraddress of the MMA8452
       * @return The value of the register
       */
      int readRegister(char addr, char *dst);
      
      int readRegister(char addr, char *dst, int nbytes);
        
       /** 
        * Write to the specified MMA8452 register.
        *
        * @param addr The internal register address
        * @param data Data to write
        */    
      int writeRegister(char addr, char data);
      
       /** 
        * Write a data buffer to the specified MMA8452 register.
        *
        * @param addr The internal register address
        * @param data Data buffer to write
        * @param nbytes The length of the data buffer to write
        */    
      int writeRegister(char addr, char *data, int nbytes);
      
      int logicalANDRegister(char addr, char mask);
      int logicalORRegister(char addr, char mask);
      int logicalXORRegister(char addr, char mask);
      
      int setDynamicRange(DynamicRange range, int toggleActivation=1);
      int setBitDepth(BitDepth depth, int toggleActivation=1);
      int setDataRate(DataRateHz dataRate, int toggleActivation=1);
      
      DynamicRange getDynamicRange();
      DataRateHz getDataRate();
      BitDepth getBitDepth();
      
      void debugRegister(char reg);
   
    private:
      int readRaw(char src, char *dst, int len);
      int maskAndApplyRegister(char reg, char mask, char value, int toggleActivation);
      
      int twelveBitToSigned(char *buf);
      int eightBitToSigned(char *buf);
      double convertCountToGravity(int count, int countsPerG);
    
      I2C _i2c;
      int _frequency;
      int _readAddress;
      int _writeAddress;
      
      BitDepth _bitDepth;
      DynamicRange _dynamicRange;
         
};