pin1,2,3,servo
Dependencies: Servo Test2Boards LSCServo ros_lib_melodic DC_Stepper_Controller_Lib
Diff: main.cpp
- Revision:
- 10:9720882ee8ee
- Parent:
- 8:e0fc4ff343f8
- Child:
- 11:d48dd2e111ba
diff -r edde48146b18 -r 9720882ee8ee main.cpp --- a/main.cpp Sat Jun 12 16:06:09 2021 +0000 +++ b/main.cpp Thu Jun 17 10:12:21 2021 +0000 @@ -28,8 +28,8 @@ DigitalOut pusher2 = D13; DigitalOut pusher1 = D12; //not in use DigitalIn but(D7); // firing pin -DigitalOut up = D11; //pneumatic part -DigitalOut down = D10; //pneumatic part +DigitalOut Up = D9; +DigitalOut down = D8; //pneumatic part LSCServo robot_arm(D1, D0); //D1 = Tx, D0 = Rx @@ -45,9 +45,9 @@ while(1){ s1.wait(); robot_arm.moveServos(3,1000,2,185,3,540,4,1000); // rotate down, tuned - robot_arm.moveServos(3,1500,2,650,3,180,4,1000); // rotate left, tuned - Thread::wait(1000); - robot_arm.moveServos(3,1000,2,650,3,180,4,500); // open the crawler + robot_arm.moveServos(3,1000,2,185,3,180,4,1000); + robot_arm.moveServos(3,500,2,700,3,180,4,1000); // rotate left, tuned + robot_arm.moveServos(3,1000,2,700,3,180,4,500); // open the crawler } } void movingArmRight() @@ -55,9 +55,9 @@ while(1){ s2.wait(); robot_arm.moveServos(3,1000,2,185,3,540,4,1000); - robot_arm.moveServos(3,1500,2,650,3,920,4,1000); // rotate left, tuned - Thread::wait(1000); - robot_arm.moveServos(3,1500,2,700,3,920,4,500); + robot_arm.moveServos(3,1000,2,185,3,920,4,1000); + robot_arm.moveServos(3,500,2,750,3,920,4,1000); // rotate left, tuned + robot_arm.moveServos(3,1000,2,680,3,920,4,500); } } void movingArmOpen() @@ -81,11 +81,11 @@ motor.set_out(0,0.4); while(!but) { - ; + motor.set_out(0,0.4); } motor.set_out(0,0); motor.reset(); - motor.move_angle(-250); + motor.move_angle(-260); } } void moving10cm(){ @@ -98,11 +98,11 @@ motor.set_out(0,1); while(!but) { - ; + motor.set_out(0, 1); } motor.set_out(0,0); motor.reset(); - motor.move_angle(-250); + motor.move_angle(-260); } } //ros function @@ -171,32 +171,39 @@ void messagepad(const Bool& _msg){ //callback of ps, not in use for now arm go down and release bool check = _msg.data; if(check){ - robot_arm.moveServos(3,1500,2,500,3,540,4,1000); + robot_arm.moveServos(3,1500,2,520,3,540,4,1000); } } void messagekeypad (const Twist& _msg){ //callback of keypad float x = _msg.linear.x; float y = _msg.linear.y; - if (x==-1){ // Rotate motor clockwise - motor.set_out(1, 0); + float z1 = _msg.linear.z; + float z2 = _msg.angular.z; + if(z1==1){ + if (x==1){ // Rotate motor clockwise + motor.set_out(0.4, 0); } - else if(x==1) { // Rotate motor anti-clockwrise - motor.set_out(0, 1); + else if(x==-1) { // Rotate motor anti-clockwrise + motor.set_out(0, 0.4); } else{ motor.set_out(0, 0); } - if (y==1){ // pump air of pnumetic part - up = 1; } - else if(y==-1) { // release air of pnumetic part + if(z2==1){ + if(y ==-1.0) + { + Up = 1; + } + else if(y==1) { // release air of pnumetic part down = 1; } else{ - up = 0; + Up = 0; down = 0; } + } } Subscriber<Bool> subsqu("button_square", &messagesqu); @@ -214,12 +221,12 @@ int main() { myled = 0; but.mode(PullUp); - up = 0; + Up = 0; down = 0; pusher1 = 0; pusher2 = 0; motor.set_pid(0.008, 0, 0, 0.10); - + nh.getHardware()->setBaud(BAUD_RATE); //set baud rate nh.initNode();