Rigado
mbed-src updated for BMD-200 evaluation board. Just pin numbers are updated.
Dependents: mbed_blinky-bmd-200 bmd-200_accel_demo firstRig
Fork of
mbed-src
by 
mbed official
Replacement for the "mbed" or "mbed-src" library when using the BMD-200 Evaluation kit. This library only remaps the pin names (i.e. LED1 points to p0.01 instead of p0.18, etc) as used by the BMD-200 Evaluation board (select the nRF51822_mkit platform). All other code is untouched.
Diff: targets/hal/TARGET_NXP/TARGET_LPC176X/PeripheralNames.h
- Revision:
- 13:0645d8841f51
- Child:
- 50:b08ceb75017d
diff -r 5fa2273de5db -r 0645d8841f51 targets/hal/TARGET_NXP/TARGET_LPC176X/PeripheralNames.h
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/hal/TARGET_NXP/TARGET_LPC176X/PeripheralNames.h Mon Aug 05 14:12:34 2013 +0300
@@ -0,0 +1,80 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2013 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#ifndef MBED_PERIPHERALNAMES_H
+#define MBED_PERIPHERALNAMES_H
+
+#include "cmsis.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+ UART_0 = (int)LPC_UART0_BASE,
+ UART_1 = (int)LPC_UART1_BASE,
+ UART_2 = (int)LPC_UART2_BASE,
+ UART_3 = (int)LPC_UART3_BASE
+} UARTName;
+
+typedef enum {
+ ADC0_0 = 0,
+ ADC0_1,
+ ADC0_2,
+ ADC0_3,
+ ADC0_4,
+ ADC0_5,
+ ADC0_6,
+ ADC0_7
+} ADCName;
+
+typedef enum {
+ DAC_0 = 0
+} DACName;
+
+typedef enum {
+ SPI_0 = (int)LPC_SSP0_BASE,
+ SPI_1 = (int)LPC_SSP1_BASE
+} SPIName;
+
+typedef enum {
+ I2C_0 = (int)LPC_I2C0_BASE,
+ I2C_1 = (int)LPC_I2C1_BASE,
+ I2C_2 = (int)LPC_I2C2_BASE
+} I2CName;
+
+typedef enum {
+ PWM_1 = 1,
+ PWM_2,
+ PWM_3,
+ PWM_4,
+ PWM_5,
+ PWM_6
+} PWMName;
+
+typedef enum {
+ CAN_1 = (int)LPC_CAN1_BASE,
+ CAN_2 = (int)LPC_CAN2_BASE
+} CANName;
+
+#define STDIO_UART_TX USBTX
+#define STDIO_UART_RX USBRX
+#define STDIO_UART UART_0
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif