Rigado / mbed-src-bmd-200

mbed-src updated for BMD-200 evaluation board. Just pin numbers are updated.

Dependents:   mbed_blinky-bmd-200 bmd-200_accel_demo firstRig

Fork of mbed-src by mbed official

Replacement for the "mbed" or "mbed-src" library when using the BMD-200 Evaluation kit. This library only remaps the pin names (i.e. LED1 points to p0.01 instead of p0.18, etc) as used by the BMD-200 Evaluation board (select the nRF51822_mkit platform). All other code is untouched.

targets/hal/TARGET_NXP/TARGET_LPC23XX/PeripheralNames.h

Committer:
mbed_official
Date:
2013-11-26
Revision:
50:b08ceb75017d
Parent:
13:0645d8841f51

File content as of revision 50:b08ceb75017d:

/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
#ifndef MBED_PERIPHERALNAMES_H
#define MBED_PERIPHERALNAMES_H

#include "cmsis.h"

#ifdef __cplusplus
extern "C" {
#endif

typedef enum {
    UART_0 = (int)LPC_UART0_BASE,
    UART_1 = (int)LPC_UART1_BASE,
    UART_2 = (int)LPC_UART2_BASE,
    UART_3 = (int)LPC_UART3_BASE
} UARTName;

typedef enum {
    ADC0_0 = 0,
    ADC0_1,
    ADC0_2,
    ADC0_3,
    ADC0_4,
    ADC0_5,
    ADC0_6,
    ADC0_7
} ADCName;

typedef enum {
    DAC_0 = 0
} DACName;

typedef enum {
    SPI_0 = (int)LPC_SSP0_BASE,
    SPI_1 = (int)LPC_SSP1_BASE
} SPIName;

typedef enum {
    I2C_0 = (int)LPC_I2C0_BASE,
    I2C_1 = (int)LPC_I2C1_BASE,
    I2C_2 = (int)LPC_I2C2_BASE
} I2CName;

typedef enum {
    PWM_1 = 1,
    PWM_2,
    PWM_3,
    PWM_4,
    PWM_5,
    PWM_6
} PWMName;

typedef enum {
     CAN_1 = (int)LPC_CAN1_BASE,
     CAN_2 = (int)LPC_CAN2_BASE
} CANName;

#define STDIO_UART_TX     USBTX
#define STDIO_UART_RX     USBRX
#define STDIO_UART        UART_0

// Default peripherals
#define MBED_SPI0         p5, p6, p7, p8
#define MBED_SPI1         p11, p12, p13, p14

#define MBED_UART0        p9, p10
#define MBED_UART1        p13, p14
#define MBED_UART2        p28, p27
#define MBED_UARTUSB      USBTX, USBRX

#define MBED_I2C0         p28, p27
#define MBED_I2C1         p9, p10

#define MBED_CAN0         p30, p29

#define MBED_ANALOGOUT0   p18

#define MBED_ANALOGIN0    p15
#define MBED_ANALOGIN1    p16
#define MBED_ANALOGIN2    p17
#define MBED_ANALOGIN3    p18
#define MBED_ANALOGIN4    p19
#define MBED_ANALOGIN5    p20

#define MBED_PWMOUT0      p26
#define MBED_PWMOUT1      p25
#define MBED_PWMOUT2      p24
#define MBED_PWMOUT3      p23
#define MBED_PWMOUT4      p22
#define MBED_PWMOUT5      p21

#ifdef __cplusplus
}
#endif

#endif