mbed-src updated for BMD-200 evaluation board. Just pin numbers are updated.

Dependents:   mbed_blinky-bmd-200 bmd-200_accel_demo firstRig

Fork of mbed-src by mbed official

Replacement for the "mbed" or "mbed-src" library when using the BMD-200 Evaluation kit. This library only remaps the pin names (i.e. LED1 points to p0.01 instead of p0.18, etc) as used by the BMD-200 Evaluation board (select the nRF51822_mkit platform). All other code is untouched.

targets/hal/TARGET_NXP/TARGET_LPC43XX/PeripheralNames.h

Committer:
bogdanm
Date:
2013-09-10
Revision:
20:4263a77256ae
Child:
256:76fd9a263045

File content as of revision 20:4263a77256ae:

/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
#ifndef MBED_PERIPHERALNAMES_H
#define MBED_PERIPHERALNAMES_H

#include "cmsis.h"

#ifdef __cplusplus
extern "C" {
#endif

typedef enum {
    UART_0 = (int)LPC_USART0_BASE,
    UART_1 = (int)LPC_UART1_BASE,
    UART_2 = (int)LPC_USART2_BASE,
    UART_3 = (int)LPC_USART3_BASE
} UARTName;

typedef enum {
    ADC0_0 = 0,
    ADC0_1,
    ADC0_2,
    ADC0_3,
    ADC0_4,
    ADC0_5,
    ADC0_6,
    ADC0_7,
    ADC1_0,
    ADC1_1,
    ADC1_2,
    ADC1_3,
    ADC1_4,
    ADC1_5,
    ADC1_6,
    ADC1_7
} ADCName;

typedef enum {
    DAC_0 = 0
} DACName;

typedef enum {
    SPI_0 = (int)LPC_SSP0_BASE,
    SPI_1 = (int)LPC_SSP1_BASE
} SPIName;

typedef enum {
    I2C_0 = (int)LPC_I2C0_BASE,
    I2C_1 = (int)LPC_I2C1_BASE
} I2CName;

typedef enum {
    PWM0_1 = 1,
    PWM0_2,
    PWM0_3,
    PWM1_1,
    PWM1_2,
    PWM1_3,
    PWM2_1,
    PWM2_2,
    PWM2_3
} PWMName;

typedef enum {
     CAN_0 = (int)LPC_C_CAN0_BASE,
     CAN_1 = (int)LPC_C_CAN1_BASE
} CANName;

#define STDIO_UART_TX     UART0_TX
#define STDIO_UART_RX     UART0_RX
#define STDIO_UART        UART_0

#ifdef __cplusplus
}
#endif

#endif