SIMO PMIC with 300mA Switching Charger
MAX77659_regs.h
- Committer:
- Okan Sahin
- Date:
- 2022-08-22
- Revision:
- 0:047a7089311e
File content as of revision 0:047a7089311e:
/******************************************************************************* * Copyright (C) 2022 Analog Devices, Inc., All rights Reserved. * * This software is protected by copyright laws of the United States and * of foreign countries. This material may also be protected by patent laws * and technology transfer regulations of the United States and of foreign * countries. This software is furnished under a license agreement and/or a * nondisclosure agreement and may only be used or reproduced in accordance * with the terms of those agreements. Dissemination of this information to * any party or parties not specified in the license agreement and/or * nondisclosure agreement is expressly prohibited. * * The above copyright notice and this permission notice shall be included * in all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. * IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY CLAIM, DAMAGES * OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR * OTHER DEALINGS IN THE SOFTWARE. * * Except as contained in this notice, the name of Maxim Integrated * Products, Inc. shall not be used except as stated in the Maxim Integrated * Products, Inc. Branding Policy. * * The mere transfer of this software does not imply any licenses * of trade secrets, proprietary technology, copyrights, patents, * trademarks, maskwork rights, or any other form of intellectual * property whatsoever. Analog Devices, Inc. retains all * ownership rights. ******************************************************************************* */ #ifndef MAX77659_REGS_H_ #define MAX77659_REGS_H_ /** * @brief INT_GLBL0 Register * * Address : 0x00 */ typedef union { unsigned char raw; struct { unsigned char gpi0_f : 1; /**< GPI Falling Interrupt. Bit 0. Note that "GPI" refers to the GPIO programmed to be an input. 0 = No GPI falling edges have occurred since the last time this bit was read. 1 = A GPI falling edge has occurred since the last time this bit was read. */ unsigned char gpi0_r : 1; /**< GPI Rising Interrupt. Bit 1. Note that "GPI" refers to the GPIO programmed to be an input. 0 = No GPI rising edges have occurred since the last time this bit was read. 1 = A GPI rising edge has occurred since the last time this bit was read. */ unsigned char nen_f : 1; /**< nEN Falling Interrupt.Bit 2. 0 = No nEN falling edges have occurred since the last time this bit was read. 1 = A nEN falling edge as occurred since the last time this bit was read. */ unsigned char nen_r : 1; /**< nEN Rising Interrupt. Bit 3. 0 = No nEN rising edges have occurred since the last time this bit was read. 1 = A nEN rising edge as occurred since the last time this bit was read. */ unsigned char tjal1_r : 1; /**< Thermal Alarm 1 Rising Interrupt. Bit 4. 0 = The junction temperature has not risen above TJAL1 since the last time this bit was read. 1 = The junction temperature has risen above TJAL1 since the last time this bit was read. */ unsigned char tjal2_r : 1; /**< Thermal Alarm 2 Rising Interrupt. Bit 5. 0 = The junction temperature has not risen above TJAL2 since the last time this bit was read. 1 = The junction temperature has risen above TJAL2 since the last time this bit was read. */ unsigned char rsvd : 1; /**< Reserved. Unutilized bit. Write to 0. Reads are don't care. Bit 6. */ unsigned char dod_r : 1; /**< LDO Dropout Detector Rising Interrupt. Bit 7. 0 = The LDO has not detected dropout since the last time this bit was read. 1 = The LDO has detected dropout since the last time this bit was read. */ } bits; } reg_int_glbl0_t; /** * @brief INT_GLBL1 Register * * Address : 0x04 */ typedef union { unsigned char raw; struct { unsigned char gpi1_f : 1; /**< GPI Falling Interrupt. Bit 0. Note that "GPI" refers to the GPIO programmed to be an input. 0 = No GPI falling edges have occurred since the last time this bit was read. 1 = A GPI falling edge has occurred since the last time this bit was read. */ unsigned char gpi1_r : 1; /**< GPI Rising Interrupt. Bit 1. Note that "GPI" refers to the GPIO programmed to be an input. 0 = No GPI rising edges have occurred since the last time this bit was read. 1 = A GPI rising edge has occurred since the last time this bit was read. */ unsigned char rsvd1 : 2; /**< Reserved. Unutilized bit. Write to 0. Reads are don't care. Bit 3:2. */ unsigned char sbb_to : 1; /**< SBB Timeout. Bit 4. 0 = NO SBB timeout occurred since the last time this bit was read 1 = SBB timeout occurred since the last time this bit was read */ unsigned char ldo_f : 1; /**< LDO Fault Interrupt. Bit 5. 0 = No fault has occurred on LDO since the last time this bit was read. 1 = LDO has fallen out of regulation since the last time this bit was read. */ unsigned char ldo1_f : 1; /**< LDO1 Fault Interrupt. Bit 6. 0 = No fault has occurred on LDO1 since the last time this bit was read. 1 = LDO1 has fallen out of regulation since the last time this bit was read. */ unsigned char rsvd2 : 2; /**< Reserved. Unutilized bit. Write to 0. Reads are don't care. Bit 7:6. */ } bits; } reg_int_glbl1_t; /** * @brief ERCFLAG Register * * Address : 0x05 */ typedef union { unsigned char raw; struct { unsigned char tovld : 1; /**< Thermal Overload. Bit 0. 0 = Thermal overload has not occurred since the last read of this register. 1 = Thermal overload has occurred since the list read of this register. This indicates that the junction temperature has exceeded 165ºC. */ unsigned char sysovlo : 1; /**< SYS Domain Overvoltage Lockout. Bit 1. 0 = The SYS domain overvoltage lockout has not occurred since this last read of this register. 1 = The SYS domain overvoltage lockout has occurred since the last read of this register. */ unsigned char avluvlo : 1; /**< AVL Domain Undervoltage Lockout. Bit 2. 0 = The AVL domain undervoltage lockout has not occurred since this last read of this register. 1 = The AVL domain undervoltage lockout has occurred since the last read of this register. */ unsigned char mrst : 1; /**< Manual Reset Timer. Bit 3. 0 = A Manual Reset has not occurred since this last read of this register. 1 = A Manual Reset has occurred since this last read of this register. */ unsigned char sft_off_f : 1; /**< Software Off Flag. Bit 4. 0 = The SFT_OFF function has not occurred since the last read of this register. 1 = The SFT_OFF function has occurred since the last read of this register. */ unsigned char sft_crst_f: 1; /**< Software Cold Reset Flag. Bit 5. 0 = The software cold reset has not occurred since the last read of this register. 1 = The software cold reset has occurred since the last read of this register. */ unsigned char wdt_off : 1; /**< Watchdog Timer OFF Flag. Bit 6. This bit sets when the watchdog timer expires and causes a power-off. 0 = Watchdog timer has not caused a power-off since the last time this bit was read. 1 = Watchdog timer has expired and caused a power-off since the last time this bit was read. */ unsigned char wdt_rst : 1; /**< Watchdog Timer Reset Flag. Bit 7. This bit sets when the watchdog timer expires and causes a power-reset. 0 = Watchdog timer has not caused a power-reset since the last time this bit was read. 1 = Watchdog timer has expired and caused a power-reset since the last time this bit was read.*/ } bits; } reg_ercflag_t; /** * @brief STAT_GLBL Register * * Address : 0x06 */ typedef union { unsigned char raw; struct { unsigned char stat_irq : 1; /**< Software Version of the nIRQ MOSFET gate drive. Bit 0. 0 = unmasked gate drive is logic low 1 = unmasked gate drive is logic high */ unsigned char stat_en : 1; /**< Debounced Status for the nEN input. Bit 1. 0 = nEN is not active (logic high) 1 = nEN is active (logic low) */ unsigned char tjal1_s : 1; /**< Thermal Alarm 1 Status. Bit 2. 0 = The junction temperature is less than TJAL1 1 = The junction temperature is greater than TJAL1 */ unsigned char tjal2_s : 1; /**< Thermal Alarm 2 Status. Bit 3. 0 = The junction temperature is less than TJAL2 1 = The junction temperature is greater than TJAL2 */ unsigned char rsvd : 1; /**< Reserved. Unutilized bit. Write to 0. Reads are don't care. */ unsigned char dod_s : 1; /**< LDO0 Dropout Detector Rising Status. Bit 5. 0 = LDO0 is not in dropout 1 = LDO0 is in dropout */ unsigned char bok : 1; /**< BOK Interrupt Status. Bit 6. 0 = Main Bias is not ready. 1 = Main Bias enabled and ready. */ unsigned char didm : 1; /**< Device Identification Bits for Metal Options. Bit 7. 0 = MAX77659 1 = Reserved */ } bits; } reg_stat_glbl_t; /** * @brief INTM_GLBL1 Register * * Address : 0x08 */ typedef union { unsigned char raw; struct { unsigned char gpi1_fm : 1; /**< GPI Falling Interrupt Mask. Bit 0. 0 = Unmasked. If GPI_F goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to GPI_F. */ unsigned char gpi1_rm : 1; /**< GPI Rising Interrupt Mask. Bit 1. 0 = Unmasked. If GPI_R goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to GPI_R. */ unsigned char rsvd1 : 2; /**< Reserved. Unutilized bit. Write to 0. Reads are don't care. Bit 3:2. */ unsigned char sbb_to_m : 1; /**< SBB Timeout Mask. Bit 4. 0 = Unmasked. If SBB_TO goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to SBB_TO */ unsigned char ldo_m : 1; /**< LDO0 Fault Interrupt. Bit 5. 0 = Unmasked. If LDO0_F goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to LDO0_F. */ unsigned char rsvd2 : 2; /**< Reserved. Unutilized bit. Write to 0. Reads are don't care. Bit 7:6. */ } bits; } reg_intm_glbl1_t; /** * @brief INTM_GLBL0 Register * * Address : 0x09 */ typedef union { unsigned char raw; struct { unsigned char gpi0_fm : 1; /**< GPI Falling Interrupt Mask. Bit 0. 0 = Unmasked. If GPI_F goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to GPI_F. */ unsigned char gpi0_rm : 1; /**< GPI Rising Interrupt Mask. Bit 1. 0 = Unmasked. If GPI_R goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to GPI_R. */ unsigned char nen_fm : 1; /**< nEN Falling Interrupt Mask. Bit 2. 0 = Unmasked. If nEN_F goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to nEN_F. */ unsigned char nen_rm : 1; /**< nEN Rising Interrupt Mask. Bit 3. 0 = Unmasked. If nEN_R goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to nEN_R. */ unsigned char tjal1_rm : 1; /**< Thermal Alarm 1 Rising Interrupt Mask. Bit 4. 0 = Unmasked. If TJAL1_R goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to TJAL1_R. */ unsigned char tjal2_rm : 1; /**< Thermal Alarm 2 Rising Interrupt Mask. Bit 5. 0 = Unmasked. If TJAL2_R goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to TJAL2_R. */ unsigned char rsvd : 1; /**< Reserved. Unutilized bit. Write to 0. Reads are don't care. Bit 6. */ unsigned char dod_rm : 1; /**< LDO Dropout Detector Rising Interrupt Mask. Bit 7. 0 = Unmasked. If DOD0_R goes from 0 to 1, then nIRQ goes low. nIRQ goes high when all interrupt bits are cleared. 1 = Masked. nIRQ does not go low due to DOD0_R. */ } bits; } reg_intm_glbl0_t; /** * @brief CNFG_GLBL Register * * Address : 0x10 */ typedef union { unsigned char raw; struct { unsigned char sft_ctrl : 2; /**< Software Reset Functions. Bit 1:0. 0b00 = No Action 0b01 = Software Cold Reset (SFT_CRST). The device powers down, resets, and the powers up again. 0b10 = Software Off (SFT_OFF). The device powers down, resets, and then remains off and waiting for a wake-up event. 0b11 = Factory-Ship Mode Enter (FSM). */ unsigned char dben_nen : 1; /**< Debounce Timer Enable for the nEN Pin. Bit 2. 0 = 500μs Debounce 1 = 30ms Debounce */ unsigned char nen_mode : 1; /**< nEN Input (ON-KEY) Default Configuration Mode. Bit 3. 0 = Push-Button Mode 1 = Slide-Switch Mode */ unsigned char sbia_en : 1; /**< Main Bias Enable Software Request. Bit 4. 0 = Main Bias not enabled by software. Note that the main bias may be on via the on/off controller. 1 = Main Bias force enabled by software. */ unsigned char sbia_lpm : 1; /**< Main Bias Low-Power Mode Software Request. Bit 5. 0 = Main Bias requested to be in Normal-Power Mode by software. 1 = Main Bias request to be in Low-Power Mode by software. */ unsigned char t_mrst : 1; /**< Sets the Manual Reset Time (tMRST). Bit 6. 0 = 8s 1 = 3.3s */ unsigned char pu_dis : 1; /**< nEN Internal Pullup Resistor. Bit 7. 0 = Strong internal nEN pullup (200kΩ) 1 = Weak internal nEN pullup (10MΩ) */ } bits; } reg_cnfg_glbl_t; /** * @brief CNFG_GPIO0 Register * * Address : 0x11 */ typedef union { unsigned char raw; struct { unsigned char gpo_dir : 1; /**< GPIO Direction. Bit 0. 0 = General purpose output (GPO) 1 = General purpose input (GPI) */ unsigned char gpo_di : 1; /**< GPIO Digital Input Value. Bit 1. 0 = Input logic low 1 = Input logic high */ unsigned char gpo_drv : 1; /**< General Purpose Output Driver Type. Bit 2. This bit is a don't care when DIR = 1 (configured as input) When set for GPO (DIR = 0): 0 = Open-Drain 1 = Push-Pull */ unsigned char gpo_do : 1; /**< General Purpose Output Data Output. Bit 3. This bit is a don't care when DIR = 1 (configured as input). When set for GPO (DIR = 0): 0 = GPIO is output is logic low 1 = GPIO is output logic high when set as push-pull output (DRV = 1). */ unsigned char dben_gpi : 1; /**< General Purpose Input Debounce Timer Enable. Bit 4. 0 = no debounce 1 = 30ms debounce */ unsigned char alt_gpio : 1; /**< Alternate Mode Enable for GPIO0. Bit 5. 0 = Standard GPIO. 1 = Active-high input, enable control for low-power mode. */ unsigned char : 1; /**< Bit 6. */ unsigned char rsvd : 1; /**< Reserved. Bit 7. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_cnfg_gpio0_t; /** * @brief CNFG_GPIO1 Register * * Address : 0x12 */ typedef union { unsigned char raw; struct { unsigned char gpo_dir : 1; /**< GPIO Direction. Bit 0. 0 = General purpose output (GPO) 1 = General purpose input (GPI) */ unsigned char gpo_di : 1; /**< GPIO Digital Input Value. Bit 1. 0 = Input logic low 1 = Input logic high */ unsigned char gpo_drv : 1; /**< General Purpose Output Driver Type. Bit 2. This bit is a don't care when DIR = 1 (configured as input) When set for GPO (DIR = 0): 0 = Open-Drain 1 = Push-Pull */ unsigned char gpo_do : 1; /**< General Purpose Output Data Output. Bit 3. This bit is a don't care when DIR = 1 (configured as input). When set for GPO (DIR = 0): 0 = GPIO is output is logic low 1 = GPIO is output logic high when set as push-pull output (DRV = 1). */ unsigned char dben_gpi : 1; /**< General Purpose Input Debounce Timer Enable. Bit 4. 0 = no debounce 1 = 30ms debounce */ unsigned char alt_gpio : 1; /**< Alternate Mode Enable for GPIO1. Bit 5. 0 = Standard GPIO. 1 = Active-high input, enable control for the DVS feature for SBB0. */ unsigned char rsvd : 2; /**< Reserved. Bit 7:6. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_cnfg_gpio1_t; /** * @brief CID Register * * Address : 0x14 */ typedef union { unsigned char raw; struct { unsigned char cid_3_0 : 4; /**< Bits 0 to 3 of the Chip Identification Code. Bit 3:0. The Chip Identification Code refers to a set of reset values in the register map, or the "OTP configuration.". */ unsigned char : 3; /**< Bit 6:4. */ unsigned char cid_7 : 1; /**< Bit 4 of the Chip Identification Code. Bit 7. The Chip Identification Code refers to a set of reset values in the register map, or the "OTP configuration.". */ } bits; } reg_cid_t; /** * @brief CNFG_WDT Register * * Address : 0x17 */ typedef union { unsigned char raw; struct { unsigned char wdt_lock : 1; /**< Factory-Set Safety Bit for the Watchdog Timer. Bit 0. 0 = Watchdog timer can be enabled and disabled with WDT_EN. 1 = Watchdog timer can not be disabled with WDT_EN. However, WDT_EN can still be used to enable the watchdog timer. */ unsigned char wdt_en : 1; /**< Watchdog Timer Enable. Bit 1. 0 = Watchdog timer is not enabled. 1 = Watchdog timer is enabled. The timer will expire if not reset by setting WDT_CLR. */ unsigned char wdt_clr : 1; /**< Watchdog Timer Clear Control. Bit 2. 0 = Watchdog timer period is not reset. 1 = Watchdog timer is reset back to tWD. */ unsigned char wdt_mode : 1; /**< Watchdog Timer Expired Action. Bit 3. 0 = Watchdog timer expire causes power-off. 1 = Watchdog timer expire causes power-reset. */ unsigned char wdt_per : 2; /**< Watchdog Timer Period. Bit 5:4. 0b00 = 16 seconds 0b01 = 32 seconds 0b10 = 64 seconds 0b11 = 128 seconds. */ unsigned char rsvd : 2; /**< Reserved. Bit 7:6. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_cnfg_wdt_t; /** * @brief INT_CHG Register * * Address : 0x01 */ typedef union { unsigned char raw; struct { unsigned char thm_i : 1; /**< Thermistor related interrupt. Bit 0. 0 = The bits in THM_DTLS[2:0] have not changed since the last time this bit was read 1 = The bits in THM_DTLS[2:0] have changed since the last time this bit was read */ unsigned char chg_i : 1; /**< Charger related interrupt. Bit 1. 0 = The bits in CHG_DTLS[3:0] have not changed since the last time this bit was read 1 = The bits in CHG_DTLS[3:0] have changed since the last time this bit was read */ unsigned char chgin_i : 1; /**< CHGIN related interrupt. Bit 2. 0 = The bits in CHGIN_DTLS[1:0] have not changed since the last time this bit was read 1 = The bits in CHGIN_DTLS[1:0] have changed since the last time this bit was read */ unsigned char tj_reg_i : 1; /**< Die junction temperature regulation interrupt. Bit 3. 0 = The die temperature has not exceeded TJ-REG since the last time this bit was read 1 = The die temperature has exceeded TJ-REG since the last time this bit was read */ unsigned char sys_ctrl_i : 1; /**< Minimum System Voltage Regulation-loop related interrupt. Bit 4. 0 = The minimum system voltage regulation loop has not engaged since the last time this bit was read 1 = The minimum system voltage regulation loop has engaged since the last time this bit was read */ unsigned char rsvd : 1; /**< Reserved. Bit 7:5. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_int_chg_t; /** * @brief STAT_CHG_A * * Address : 0x02 */ typedef union { unsigned char raw; struct { unsigned char thm_dtls : 3; /**< Battery Temperature Details. Bit 2:0. 0b000 = Thermistor is disabled (THM_EN = 0) 0b001 = Battery is cold as programmed by THM_COLD[1:0] If thermistor and charger are enabled while the battery is cold, a battery temperature fault will occur. 0b010 = Battery is cool as programmed by THM_COOL[1:0] 0b011 = Battery is warm as programmed by THM_WARM[1:0] 0b100 = Battery is hot as programmed by THM_HOT[1:0]. If thermistor and charger are enabled while the battery is hot, a battery temperature fault will occur. 0b101 = Battery is in the normal temperature region 0b110 - 0b111 = reserved */ unsigned char tj_reg_stat : 1; /**< Maximum Junction Temperature Regulation Loop Status. Bit 3. 0 = The maximum junction temperature regulation loop is not engaged 1 = The maximum junction temperature regulation loop has engaged to regulate the junction temperature to less than TJ-REG */ unsigned char vsys_min_stat : 1; /**< Minimum System Voltage Regulation Loop Status. Bit 4. 0 = The minimum system voltage regulation loop is not enganged 1 = The minimum system voltage regulation loop is engaged to regulate VSYS ≥ VSYS-MIN */ unsigned char rsvd : 3; /**< Reserved. Bit 7:5. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_stat_chg_a_t; /** * @brief STAT_CHG_B * * Address : 0x03 */ typedef union { unsigned char raw; struct { unsigned char time_sus : 1; /**< Time Suspend Indicator. Bit 0. 0 = The charger's timers are either not active, or not suspended 1 = The charger's active timer is suspended due to one of three reasons: charge current dropped below 20% of IFAST-CHG while the charger state machine is in FAST CHARGE CC mode, the charger is in SUPPLEMENT mode, or the charger state machine is in BATTERY TEMPERATURE FAULT mode. */ unsigned char chg : 1; /**< Quick Charger Status. Bit 1. 0 = Charging is not happening 1 = Charging is happening */ unsigned char chgin_dtls : 2; /**< CHGIN Status Detail. Bit 3:2. 0b00 = The CHGIN input voltage is below the UVLO threshold (VCHGIN < VUVLO) 0b01 = The CHGIN input voltage is above the OVP threshold (VCHGIN > VOVP) 0b10 = The CHGIN input is being debounced (no power accepted from CHGIN during debounce) 0b11 = The CHGIN input is okay and debounced */ unsigned char chg_dtls : 4; /**< Charger Details. Bit 7:4. 0b0000 = Off 0b0001 = Prequalification mode 0b0010 = Fast-charge constant-current (CC) mode 0b0011 = JEITA modified fast-charge constant-current mode 0b0100 = Fast-charge constant-voltage (CV) mode 0b0101 = JEITA modified fast-charge constant-voltage mode 0b0110 = Top-off mode 0b0111 = JEITA modified top-off mode 0b1000 = Done 0b1001 = JEITA modified done (done was entered through the JEITA-modified fast-charge states) 0b1010 = Prequalification timer fault 0b1011 = Fast-charge timer fault 0b1100 = Battery temperature fault 0b1101 - 0b1111 = reserved */ } bits; } reg_stat_chg_b_t; /** * @brief INT_M_CHG Register * * Address : 0x07 */ typedef union { unsigned char raw; struct { unsigned char thm_m : 1; /**< Setting this bit prevents the THM_I bit from causing hardware IRQs. Bit 0. 0 = THM_I is not masked 1 = THM_I is masked */ unsigned char chg_m : 1; /**< Setting this bit prevents the CHG_I bit from causing hardware IRQs. Bit 1. 0 = CHG_I is not masked 1 = CHG_I is masked */ unsigned char chgin_m : 1; /**< Setting this bit prevents the CHGIN_I bit from causing hardware IRQs. Bit 2. 0 = CHGIN_I is not masked 1 = CHGIN_I is masked */ unsigned char tj_reg_m : 1; /**< Setting this bit prevents the TJREG_I bit from causing hardware IRQs. Bit 3. 0 = TJREG_I is not masked 1 = TJREG_I is masked */ unsigned char sys_ctrl_m : 1; /**< Setting this bit prevents the SYS_CTRL_I bit from causing hardware IRQs. Bit 4. 0 = SYS_CTRL_I is not masked 1 = SYS_CTRL_I is masked */ unsigned char rsvd : 3; /**< Reserved. Bit 7:5. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_int_m_chg_t; /** * @brief CNFG_CHG_A * * Address : 0x20 */ typedef union { unsigned char raw; struct { unsigned char thm_cold : 2; /**< Sets the VCOLD JEITA Temperature Threshold. Bit 1:0. 0b00 = VCOLD = 1.024V (-10ºC for β = 3380K) 0b01 = VCOLD = 0.976V (-5ºC for β = 3380K) 0b10 = VCOLD = 0.923V (0ºC for β = 3380K) 0b11 = VCOLD = 0.867V (5ºC for β = 3380K) */ unsigned char thm_cool : 2; /**< Sets the VCOOL JEITA Temperature Threshold. Bit 3:2. 0b00 = VCOOL = 0.923V (0ºC for β = 3380K) 0b01 = VCOOL = 0.867V (5ºC for β = 3380K) 0b10 = VCOOL = 0.807V (10ºC for β = 3380K) 0b11 = VCOOL = 0.747V (15ºC for β = 3380K) */ unsigned char thm_warm : 2; /**< Sets the VWARM JEITA Temperature Threshold. Bit 5:4. 0b00 = VWARM = 0.511V (35ºC for β = 3380K) 0b01 = VWARM = 0.459V (40ºC for β = 3380K) 0b10 = VWARM = 0.411V (45ºC for β = 3380K) 0b11 = VWARM = 0.367V (50ºC for β = 3380K) */ unsigned char thm_hot : 2; /**< Sets the VHOT JEITA Temperature Threshold. Bit 7:6. 0b00 = VHOT = 0.411V (45ºC for β = 3380K) 0b01 = VHOT = 0.367V (50ºC for β = 3380K) 0b10 = VHOT = 0.327V (55ºC for β = 3380K) 0b11 = VHOT = 0.291V (60ºC for β = 3380K) */ } bits; } reg_cnfg_chg_a_t; /** * @brief CNFG_CHG_B * * Address : 0x21 */ typedef union { unsigned char raw; struct { unsigned char chg_en : 1; /**< Charger Enable. Bit 0. 0 = the battery charger is disabled 1 = the battery charger is enabled */ unsigned char i_pq : 1; /**< Sets the prequalification charge current (IPQ) as a percentage of IFAST-CHG. Bit 1. 0 = 10% 1 = 20% */ unsigned char rsvd : 6; /**< Reserved. Bit 7:2. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_cnfg_chg_b_t; /** * @brief CNFG_CHG_C * * Address : 0x22 */ typedef union { unsigned char raw; struct { unsigned char t_topoff : 3; /**< Top-off timer value (tTO). Bit 2:0. 0b000 = 0 minutes 0b001 = 5 minutes 0b010 = 10 minutes 0b011 = 15 minutes 0b100 = 20 minutes 0b101 = 25 minutes 0b110 = 30 minutes 0b111 = 35 minutes */ unsigned char i_term : 2; /**< Charger Termination Current (ITERM). Bit 4:3. 00 = 5% 01 = 7.5% 10 = 10% 11 = 15% */ unsigned char chg_pq : 3; /**< Battery prequalification voltage threshold (VPQ). Bit 7:5. 0b000 = 2.3V 0b001 = 2.4V 0b010 = 2.5V 0b011 = 2.6V 0b100 = 2.7V 0b101 = 2.8V 0b110 = 2.9V 0b111 = 3.0V */ } bits; } reg_cnfg_chg_c_t; /** * @brief CNFG_CHG_D * * Address : 0x23 */ typedef union { unsigned char raw; struct { unsigned char vsys_min : 2; /**< Minimum SYS Voltage . Bit 1:0. 0x0 = 3.2V 0x1 = 3.3V 0x2 = 3.4V 0x3 = 3.5V */ unsigned char rsvd : 2; /**< Reserved. Bit 3:2. Unutilized bit. Write to 0. Reads are don't care. */ unsigned char vsys_hdrm : 1; /**< SYS Headroom Voltage Regulation. Bit 4. 0b0 = 0.15V 0b1 = 0.20V */ unsigned char tj_reg : 3; /**< Sets the die junction temperature regulation point, TJ-REG. Bit 7:5. 0b000 = 60ºC 0b001 = 70ºC 0b010 = 80ºC 0b011 = 90ºC 0b100 - 0b111 = 100ºC */ } bits; } reg_cnfg_chg_d_t; /** * @brief CNFG_CHG_E * * Address : 0x25 */ typedef union { unsigned char raw; struct { unsigned char t_fast_chg : 2; /**< System voltage regulation (VSYS-REG). Bit 1:0. 0b00 = timer disabled 0b01 = 3 hours 0b10 = 5 hours 0b11 = 7 hours */ unsigned char chg_cc : 6; /**< Sets the fast-charge constant current value, IFAST-CHG. Bit 7:2. 0x0 = 7.5mA 0x1 = 15.0mA 0x2 = 22.5mA ... 0x26 = 292.5mA 0x27 - 0x3F = 300.0mA */ } bits; } reg_cnfg_chg_e_t; /** * @brief CNFG_CHG_F * * Address : 0x25 */ typedef union { unsigned char raw; struct { unsigned char : 1; /**< Bit 0*/ unsigned char thm_en : 1; /**< Thermistor enable bit. Bit 1. 0 = Thermistor is disabled 1 = Thermistor is enabled */ unsigned char chg_cc_jeita : 6; /**< Sets IFAST-CHG-JEITA for when the battery is either cool or warm as defined by the VCOOL and VWARM temperature thresholds. Bit 7:2. 0x0 = 7.5mA 0x1 = 15.0mA 0x2 = 22.5mA ... 0x26 = 292.5mA 0x27 - 0x3F = 300.0mA */ } bits; } reg_cnfg_chg_f_t; /** * @brief CNFG_CHG_G * * Address : 0x26 */ typedef union { unsigned char raw; struct { unsigned char rsvd : 1; /**< Reserved. Bit 0. Unutilized bit. Write to 0. Reads are don't care.*/ unsigned char usbs : 1; /**< Setting this bit places CHGIN in USB suspend mode. Bit 1. 0 = CHGIN is not suspended and may draw current from an adapter source 1 = CHGIN is suspended and may draw no current from an adapter source */ unsigned char chg_cv : 6; /**< Sets fast-charge battery regulation voltage, VFAST-CHG. Bit 7:2. 0x0 = 3.600V 0x1 = 3.625V 0x2 = 3.650V ... 0x27 = 4.575V 0x28 - 0x3F = 4.600V */ } bits; } reg_cnfg_chg_g_t; /** * @brief CNFG_CHG_H * * Address : 0x27 */ typedef union { unsigned char raw; struct { unsigned char rsvd : 2; /**< Reserved. Bit 1:0. Unutilized bit. Write to 0. Reads are don't care.*/ unsigned char chg_cv_jeita : 6; /**< Sets fast-charge battery regulation voltage, VFAST-CHG. Bit 7:2. 0x0 = 3.600V 0x1 = 3.625V 0x2 = 3.650V ... 0x27 = 4.575V 0x28 - 0x3F = 4.600V */ } bits; } reg_cnfg_chg_h_t; /** * @brief CNFG_CHG_I * * Address : 0x28 */ typedef union { unsigned char raw; struct { unsigned char mux_sel : 4; /**< Selects the analog channel to connect to AMUX. Bit 3:0. 0b0000 = Multiplexer is disabled and AMUX is high-impedance. 0b0001 = CHGIN voltage monitor. 0b0010 = CHGIN current monitor. 0b0011 = BATT voltage monitor. 0b0100 = BATT charge current monitor. Valid only while battery charging is happening (CHG = 1). 0b0101 = BATT discharge current monitor normal measurement. 0b0110 = BATT discharge current monitor nulling measurement. 0b0111 = THM voltage monitor 0b1000 = TBIAS voltage monitor 0b1001 = AGND voltage monitor (through 100Ω pull-down resistor) 0b1010 - 0b1111 = SYS voltage monitor */ unsigned char imon_dischg_scale : 4; /**< Selects the battery discharge current full-scale current value. Bit 7:4. 0x0 = 8.2mA 0x1 = 40.5mA 0x2 = 72.3mA 0x3 = 103.4mA 0x4 = 134.1mA 0x5 = 164.1mA 0x6 = 193.7mA 0x7 = 222.7mA 0x8 = 251.2mA 0x9 = 279.3mA 0xA - 0xF = 300.0mA */ } bits; } reg_cnfg_chg_i_t; /** * @brief CNFG_SBB0_A * * Address : 0x29 */ typedef union { unsigned char raw; struct { unsigned char tv_sbb0 : 7; /**< SIMO Buck-Boost Channel 0 Target Output Voltage. Bit 6:0. 0x00 = 0.500V 0x01 = 0.525V 0x02 = 0.550V 0x03 = 0.575V 0x04 = 0.600V ... 0x30 = 1.700V 0x31 = 1.750V 0x32 = 1.800V ... 0x7B = 5.450V 0x7C = 5.500V 0x7D to 0x7F = Reserved */ unsigned char : 1; /**< Bit 7. */ } bits; } reg_cnfg_sbb0_a_t; /** * @brief CNFG_SBB0_B * * Address : 0x2A */ typedef union { unsigned char raw; struct { unsigned char en_sbb0 : 3; /**< Enable Control for SIMO Buck-Boost Channel 0, selecting either an FPS slot the channel powers-up and powers-down in or whether the channel is forced on or off. Bit 2:0. 0b000 = FPS slot 0 0b001 = FPS slot 1 0b010 = FPS slot 2 0b011 = FPS slot 3 0b100 = Off irrespective of FPS 0b101 = same as 0b100 0b110 = On irrespective of FPS 0b111 = same as 0b110 */ unsigned char ade_sbb0 : 1; /**< SIMO Buck-Boost Channel 0 Active-Discharge Enable. Bit 3. 0 = The active discharge function is disabled. When SBB0 is disabled, its discharge rate is a function of the output capacitance and the external load. 1 = The active discharge function is enabled. When SBB0 is disabled, an internal resistor (RAD_SBB0) is activated from SBB0 to PGND to help the output voltage discharge. */ unsigned char : 2; /**< Bit 5:4*/ unsigned char op_mode : 1; /**< Operation mode of SBB0. Bit 6. 0 = Buck-Boost Mode 1 = Buck Mode*/ unsigned char rsvd : 1; /**< Reserved. Bit 7. Unutilized bit. Write to 0. Reads are don't care.*/ } bits; } reg_cnfg_sbb0_b_t; /** * @brief CNFG_SBB1_A * * Address : 0x2B */ typedef union { unsigned char raw; struct { unsigned char tv_sbb1 : 7; /**< SIMO Buck-Boost Channel 1 Target Output Voltage. Bit 6:0. 0x00 = 0.500V 0x01 = 0.525V 0x02 = 0.550V 0x03 = 0.575V 0x04 = 0.600V ... 0x30 = 1.700V 0x31 = 1.750V 0x32 = 1.800V ... 0x7B = 5.450V 0x7C = 5.500V 0x7D to 0x7F = Reserved */ unsigned char : 1; /**< Bit 7. */ } bits; } reg_cnfg_sbb1_a_t; /** * @brief CNFG_SBB1_B * * Address : 0x2C */ typedef union { unsigned char raw; struct { unsigned char en_sbb1 : 3; /**< Enable Control for SIMO Buck-Boost Channel 1, selecting either an FPS slot the channel powers-up and powers-down in or whether the channel is forced on or off. Bit 2:0. 0b000 = FPS slot 0 0b001 = FPS slot 1 0b010 = FPS slot 2 0b011 = FPS slot 3 0b100 = Off irrespective of FPS 0b101 = same as 0b100 0b110 = On irrespective of FPS 0b111 = same as 0b110 */ unsigned char ade_sbb1 : 1; /**< SIMO Buck-Boost Channel 1 Active-Discharge Enable. Bit 3. 0 = The active discharge function is disabled. When SBB0 is disabled, its discharge rate is a function of the output capacitance and the external load. 1 = The active discharge function is enabled. When SBB0 is disabled, an internal resistor (RAD_SBB0) is activated from SBB0 to PGND to help the output voltage discharge. */ unsigned char : 2; /**< Bit 5:4.*/ unsigned char op_mode : 1; /**< Operation mode of SBB1. Bit 6. 0 = Buck-Boost Mode 1 = Buck Mode*/ unsigned char rsvd : 1; /**< Reserved. Bit 7. Unutilized bit. Write to 0. Reads are don't care.*/ } bits; } reg_cnfg_sbb1_b_t; /** * @brief CNFG_SBB2_A * * Address : 0x2D */ typedef union { unsigned char raw; struct { unsigned char tv_sbb2 : 7; /**< SIMO Buck-Boost Channel 2 Target Output Voltage. Bit 6:0. 0x00 = 0.500V 0x01 = 0.525V 0x02 = 0.550V 0x03 = 0.575V 0x04 = 0.600V ... 0x30 = 1.700V 0x31 = 1.750V 0x32 = 1.800V ... 0x7B = 5.450V 0x7C = 5.500V 0x7D to 0x7F = Reserved */ unsigned char : 1; /**< Bit 7. */ } bits; } reg_cnfg_sbb2_a_t; /** * @brief CNFG_SBB2_B * * Address : 0x2E */ typedef union { unsigned char raw; struct { unsigned char en_sbb2 : 3; /**< Enable Control for SIMO Buck-Boost Channel 2, selecting either an FPS slot the channel powers-up and powers-down in or whether the channel is forced on or off. Bit 2:0. 0b000 = FPS slot 0 0b001 = FPS slot 1 0b010 = FPS slot 2 0b011 = FPS slot 3 0b100 = Off irrespective of FPS 0b101 = same as 0b100 0b110 = On irrespective of FPS 0b111 = same as 0b110 */ unsigned char ade_sbb2 : 1; /**< SIMO Buck-Boost Channel 2 Active-Discharge Enable Bit 3. 0 = The active discharge function is disabled. When SBB0 is disabled, its discharge rate is a function of the output capacitance and the external load. 1 = The active discharge function is enabled. When SBB0 is disabled, an internal resistor (RAD_SBB0) is activated from SBB0 to PGND to help the output voltage discharge. */ unsigned char : 2; /**< Bit 5:4. */ unsigned char op_mode : 1; /**< Operation mode of SBB2. Bit 6. 0 = Buck-Boost Mode 1 = Buck Mode*/ unsigned char rsvd : 1; /**< Reserved. Bit 7. Unutilized bit. Write to 0. Reads are don't care.*/ } bits; } reg_cnfg_sbb2_b_t; /** * @brief CNFG_SBB_TOP * * Address : 0x2F */ typedef union { unsigned char raw; struct { unsigned char drv_sbb : 2; /**< SIMO Buck-Boost (all channels) Drive Strength Trim. Bit 1:0. 0b00 = fastest transition time 0b01 = a little slower than 0b00 0b10 = a little slower than 0b01 0b11 = a little slower than 0b10 */ unsigned char : 5; /**< Bit 6:2. */ unsigned char op_mode_chg : 1; /**< Operation mode of the charging channel of SIMO. Bit 7. 0 = Buck-boost mode 1 = Buck mode */ } bits; } reg_cnfg_sbb_top_t; /** * @brief CNFG_SBB_TOP_B * * Address : 0x30 */ typedef union { unsigned char raw; struct { unsigned char ip_sbb0 : 2; /**< SIMO Buck-Boost Channel 0 Peak Current Limit. Bit 1:0. 0b00 = 1.000A 0b01 = 0.750A 0b10 = 0.500A 0b11 = 0.333A */ unsigned char ip_sbb1 : 2; /**< SIMO Buck-Boost Channel 1 Peak Current Limit. Bit 3:2. 0b00 = 1.000A 0b01 = 0.750A 0b10 = 0.500A 0b11 = 0.333A */ unsigned char ip_sbb2 : 2; /**< SIMO Buck-Boost Channel 2 Peak Current Limit. Bit 5:4. 0b00 = 1.000A 0b01 = 0.750A 0b10 = 0.500A 0b11 = 0.333A */ unsigned char ip_chg : 2; /**< SIMO Buck-Boost Charging Channel Peak Current Limit. Bit 7:6. 0b00 = 2.000A 0b01 = 1.500A 0b10 = 1.000A 0b11 = 0.500A */ } bits; } reg_cnfg_sbb_top_b_t; /** * @brief CNFG_LDO0_A * * Address : 0x38 */ typedef union { unsigned char raw; struct { unsigned char tv_ldo_volt : 7; /**< LDO Target Output Voltage This 7-bit configuration is a linear transfer function that starts at 0.5V and ends at 3.675V, with 25mV increments. Bit 6:0. 0x00 = 0.500V 0x01 = 0.525V 0x02 = 0.550V 0x03 = 0.575V 0x04 = 0.600V 0x05 = 0.625V 0x06 = 0.650V ... 0x7D = 3.625V 0x7E = 3.650V 0x7F = 3.675V */ unsigned char tv_ldo_offset : 1; /**< LDO Output Voltage. This bit applies a 1.325V offset to the output voltage of the LDO. Bit 7. 0b0 = No offset 0b1 = 1.325V offset*/ } bits; } reg_cnfg_ldo0_a_t; /** * @brief CNFG_LDO0_B * * Address : 0x39 */ typedef union { unsigned char raw; struct { unsigned char en_ldo : 3; /**< Enable Control for LDO0, selecting either an FPS slot the channel powers-up and powers-down in or whether the channel is forced on or off. Bit 2:0. 0b000 = FPS slot 0 0b001 = FPS slot 1 0b010 = FPS slot 2 0b011 = FPS slot 3 0b100 = Off irrespective of FPS 0b101 = same as 0b100 0b110 = On irrespective of FPS 0b111 = same as 0b110 */ unsigned char ade_ldo : 1; /**< LDO0 Active-Discharge Enable. Bit 3. 0 = The active discharge function is disabled. 1 = The active discharge function is enabled. */ unsigned char ldo_md : 1; /**< Operation mode of LDO0. Bit 4. 0 = Low Dropout Linear Regulator (LDO) Mode 1 = Load Switch (LSW) Mode */ unsigned char rsvd : 3; /**< Bit 7:5. Reserved. Unutilized bit. Write to 0. Reads are don't care. */ } bits; } reg_cnfg_ldo0_b_t; #endif /* MAX77659_REGS_H_ */