La Suno / UniGraphic

Basically i glued Peter Drescher and Simon Ford libs in a GraphicsDisplay class, then derived TFT or LCD class (which inherits Protocols class), then the most derived ones (Inits), which are per-display and are the only part needed to be adapted to diff hw.

Dependents:   afero_poc15_180216 afero_poc15_180223 afero_poc15_180302 afero_poc15_180403R ... more

Fork of UniGraphic by GraphicsDisplay

UniGraphic for La Suno Version.
To go with La Suno, WatchDog Reset functions were added in ILI9341.

Diff: Inits/UC1608.cpp

Revision:
1:ff019d22b275
Parent:
0:75ec1b3cde17
Child:
3:48f3282c2be8
diff -r 75ec1b3cde17 -r ff019d22b275 Inits/UC1608.cpp
--- a/Inits/UC1608.cpp	Thu Feb 12 22:22:47 2015 +0000
+++ b/Inits/UC1608.cpp	Fri Feb 13 15:25:10 2015 +0000
@@ -21,8 +21,8 @@
     set_orientation(1);
     locate(0,0);
 }
-UC1608::UC1608(proto_t displayproto, PinName mosi, PinName miso, PinName sclk, PinName CS, PinName reset, PinName DC, const char *name)
-    : LCD(displayproto, mosi, miso, sclk, CS, reset, DC, LCDSIZE_X, LCDSIZE_Y, IC_X_SEGS, IC_Y_COMS, name)
+UC1608::UC1608(proto_t displayproto, int Hz, PinName mosi, PinName miso, PinName sclk, PinName CS, PinName reset, PinName DC, const char *name)
+    : LCD(displayproto, Hz, mosi, miso, sclk, CS, reset, DC, LCDSIZE_X, LCDSIZE_Y, IC_X_SEGS, IC_Y_COMS, name)
 {
     hw_reset();
     BusEnable(true);
@@ -36,30 +36,30 @@
 {
     /* Start Initial Sequence ----------------------------------------------------*/
     
-  //  wr_cmd(0xE2);   //  sw reset
+  //  wr_cmd8(0xE2);   //  sw reset
     wait_ms(15);
     
-    wr_cmd(0x27);   // Multiplex rate :128   set temperature consenpation 0%
-    wr_cmd(0xEA);   //set bias:1/12bias
+    wr_cmd8(0x27);   // Multiplex rate :128   set temperature consenpation 0%
+    wr_cmd8(0xEA);   //set bias:1/12bias
 
-    wr_cmd(0xC4);   // set mirror MX=1,MY=0 (controller->display SEGs wiring inverted)
-   // wr_cmd(0xA0);   // ADC select seg0-seg223
-    //wr_cmd(0xA1);   // ADC select seg223-seg0
-   // wr_cmd(0xC8);   // SHL select com63-com0
-    //wr_cmd(0xC0);   // SHL select com0-com63
+    wr_cmd8(0xC4);   // set mirror MX=1,MY=0 (controller->display SEGs wiring inverted)
+   // wr_cmd8(0xA0);   // ADC select seg0-seg223
+    //wr_cmd8(0xA1);   // ADC select seg223-seg0
+   // wr_cmd8(0xC8);   // SHL select com63-com0
+    //wr_cmd8(0xC0);   // SHL select com0-com63
 
-    wr_cmd(0x2F);   //  //Power Control:internal, LCD capacitance 60nf-90nf
+    wr_cmd8(0x2F);   //  //Power Control:internal, LCD capacitance 60nf-90nf
     wait_ms(10);
     
-   // wr_cmd(0x81);//Set Gain and Potentiometer
-  //  wr_cmd(0x40|46);//Set Gain and Potentiometer  xx xxxxxx
+   // wr_cmd8(0x81);//Set Gain and Potentiometer
+  //  wr_cmd8(0x40|46);//Set Gain and Potentiometer  xx xxxxxx
     set_contrast(46);
     
-    wr_cmd(0x88);   //disable colum/page address wraparound
-    wr_cmd(0xA4);   //  LCD display ram (EntireDisplayOn disable)
-    wr_cmd(0x40);   // start line = 0
-    wr_cmd(0xA6);     // display normal (1 = illuminated)
-    wr_cmd(0xAF);     // display ON 
+    wr_cmd8(0x88);   //disable colum/page address wraparound
+    wr_cmd8(0xA4);   //  LCD display ram (EntireDisplayOn disable)
+    wr_cmd8(0x40);   // start line = 0
+    wr_cmd8(0xA6);     // display normal (1 = illuminated)
+    wr_cmd8(0xAF);     // display ON 
 
 }
 ////////////////////////////////////////////////////////////////////
@@ -70,24 +70,25 @@
     switch (mode)
     {
         case(NONE):
-            wr_cmd(0xC4); // this is in real X mirror command, but my display have SEGs wired inverted, so assume this is the default no-x-mirror
+            wr_cmd8(0xC4); // this is in real X mirror command, but my display have SEGs wired inverted, so assume this is the default no-x-mirror
             break;
         case(X):
-            wr_cmd(0xC0);
+            wr_cmd8(0xC0);
             break;
         case(Y):
-            wr_cmd(0xCC);
+            wr_cmd8(0xCC);
             break;
         case(XY):
-            wr_cmd(0xC8);
+            wr_cmd8(0xC8);
             break;
     }
 }
 void UC1608::set_contrast(int o)
 {
     contrast = o;
-    wr_cmd(0x81);      //  set volume
-    wr_cmd(0x40|(o&0x3F));
+  //  wr_cmd8(0x81);      //  set volume
+  //  wr_cmd8(0x40|(o&0x3F));
+    wr_cmd16(0x8140|(o&0x3F));
 }
 void UC1608::BusEnable(bool enable)
 {