Pin usage: MOSI(D4), MISO(D5), SCK(D3), CS(D6), format(8, 3) Test OK.
Fork of LSM6DS3 by
Diff: LSM6DS3.h
- Revision:
- 0:301b2cb34ead
- Child:
- 1:cc2caaf5536c
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/LSM6DS3.h Fri Feb 19 09:50:40 2016 +0000 @@ -0,0 +1,176 @@ +#ifndef __LSM6DS3IMU_H__ +#define __LSM6DS3IMU_H__ + + +#include "mbed.h" +#include "stdint.h" +#include "LSM6DS3_Types.h" +#include "LSM6DS3_Registers.h" + +#include "math.h" + +#define I2C_MODE 0 +#define SPI_MODE 1 + +// Return values +typedef enum +{ + IMU_SUCCESS, + IMU_HW_ERROR, + IMU_NOT_SUPPORTED, + IMU_GENERIC_ERROR, + IMU_OUT_OF_BOUNDS, + IMU_ALL_ONES_WARNING, + //... +} status_t; + +//This is the core operational class of the driver. +// LSM6DS3Core contains only read and write operations towards the IMU. +// To use the higher level functions, use the class LSM6DS3 which inherits +// this class. +//========================self define================= + +//==================================================== + +class LSM6DS3Core +{ +public: + LSM6DS3Core( uint8_t ); + LSM6DS3Core( uint8_t, uint8_t ); + // ~LSM6DS3Core() = default; + + status_t beginCore( void ); + + //The following utilities read and write to the IMU + + //ReadRegisterRegion takes a uint8 array address as input and reads + // a chunk of memory into that array. + status_t readRegisterRegion(uint8_t*, uint8_t, uint8_t ); + + //readRegister reads one 8-bit register + status_t readRegister(uint8_t*, uint8_t); + + //Reads two 8-bit regs, LSByte then MSByte order, and concatenates them. + // Acts as a 16-bit read operation + status_t readRegisterInt16(int16_t*, uint8_t offset ); + + //Writes an 8-bit byte; + status_t writeRegister(uint8_t, uint8_t); + + //Change to embedded page + status_t embeddedPage( void ); + + //Change to base page + status_t basePage( void ); + +private: + + //Communication stuff + uint8_t commInterface; + uint8_t I2CAddress; + uint8_t chipSelectPin; + +}; + +//This struct holds the settings the driver uses to do calculations +struct SensorSettings { +public: + //Gyro settings + uint8_t gyroEnabled; + uint16_t gyroRange; + uint16_t gyroSampleRate; + uint16_t gyroBandWidth; + + uint8_t gyroFifoEnabled; + uint8_t gyroFifoDecimation; + + //Accelerometer settings + uint8_t accelEnabled; + uint8_t accelODROff; + uint16_t accelRange; + uint16_t accelSampleRate; + uint16_t accelBandWidth; + + uint8_t accelFifoEnabled; + uint8_t accelFifoDecimation; + + //Temperature settings + uint8_t tempEnabled; + + //Non-basic mode settings + uint8_t commMode; + + //FIFO control data + uint16_t fifoThreshold; + int16_t fifoSampleRate; + uint8_t fifoModeWord; + +}; + + +//This is the highest level class of the driver. +// +// class LSM6DS3 inherits the core and makes use of the beginCore() +//method through it's own begin() method. It also contains the +//settings struct to hold user settings. + +class LSM6DS3 : public LSM6DS3Core +{ +public: + //IMU settings + SensorSettings settings; + + //Error checking + uint16_t allOnesCounter; + uint16_t nonSuccessCounter; + + //Constructor generates default SensorSettings. + //(over-ride after construction if desired) + LSM6DS3( uint8_t busType = I2C_MODE, uint8_t inputArg = 0x6B ); +// ~LSM6DS3() = default; + + //Call to apply SensorSettings + status_t begin(void); + + //Returns the raw bits from the sensor cast as 16-bit signed integers + int16_t readRawAccelX( void ); + int16_t readRawAccelY( void ); + int16_t readRawAccelZ( void ); + int16_t readRawGyroX( void ); + int16_t readRawGyroY( void ); + int16_t readRawGyroZ( void ); + + int16_t accelOffset[3]; + int16_t gyroOffset[3]; + void setOffset(int16_t, int16_t, int16_t, int16_t, int16_t, int16_t); + + + + //Returns the values as floats. Inside, this calls readRaw___(); + float readFloatAccelX( void ); + float readFloatAccelY( void ); + float readFloatAccelZ( void ); + float readFloatGyroX( void ); + float readFloatGyroY( void ); + float readFloatGyroZ( void ); + + //Temperature related methods + int16_t readRawTemp( void ); + float readTempC( void ); + float readTempF( void ); + + //FIFO stuff + void fifoBegin( void ); + void fifoClear( void ); + int16_t fifoRead( void ); + uint16_t fifoGetStatus( void ); + void fifoEnd( void ); + + float calcGyro( int32_t ); + float calcAccel( int32_t ); + +private: + +}; + +#endif \ No newline at end of file