File content as of revision 5:08f338b5e4d9:

#include "mbed.h"

//Photointerrupter input pins
#define I1pin D6
#define I2pin D11
#define I3pin D12

//Incremental encoder input pins
#define CHA   D4
#define CHB   D5

//Motor Drive output pins   //Mask in output byte
#define L1Lpin D9           //0x01
#define L1Hpin D10           //0x02
#define L2Lpin D1           //0x04
#define L2Hpin D2          //0x08
#define L3Lpin D0           //0x10
#define L3Hpin D3          //0x20

//Motor current sense
#define MCSPpin   A1
#define MCSNpin   A0

//Mapping from sequential drive states to motor phase outputs
/*
State   L1  L2  L3
0       H   -   L
1       -   H   L
2       L   H   -
3       L   -   H
4       -   L   H
5       H   L   -
6       -   -   -
7       -   -   -
*/
//Drive state to output table
const int8_t driveTable[] = {0x12,0x18,0x09,0x21,0x24,0x06,0x00,0x00};

//Mapping from interrupter inputs to sequential rotor states. 0x00 and 0x07 are not valid
const int8_t stateMap[] = {0x07,0x05,0x03,0x04,0x01,0x00,0x02,0x07};  
//const int8_t stateMap[] = {0x07,0x01,0x03,0x02,0x05,0x00,0x04,0x07}; //Alternative if phase order of input or drive is reversed

//Phase lead to make motor spin
const int8_t lead = 2;  //2 for forwards, -2 for backwards

//Status LED
DigitalOut led1(LED1);

//Photointerrupter inputs
DigitalIn I1(I1pin);
DigitalIn I2(I2pin);
DigitalIn I3(I3pin);

//Motor Drive outputs
DigitalOut L1L(L1Lpin);
DigitalOut L1H(L1Hpin);
DigitalOut L2L(L2Lpin);
DigitalOut L2H(L2Hpin);
DigitalOut L3L(L3Lpin);
DigitalOut L3H(L3Hpin);

//Set a given drive state
void motorOut(int8_t driveState){
    
    //Lookup the output byte from the drive state.
    int8_t driveOut = driveTable[driveState & 0x07];
      
    //Turn off first
    if (~driveOut & 0x01) L1L = 0;
    if (~driveOut & 0x02) L1H = 1;
    if (~driveOut & 0x04) L2L = 0;
    if (~driveOut & 0x08) L2H = 1;
    if (~driveOut & 0x10) L3L = 0;
    if (~driveOut & 0x20) L3H = 1;
    
    //Then turn on
    if (driveOut & 0x01) L1L = 1;
    if (driveOut & 0x02) L1H = 0;
    if (driveOut & 0x04) L2L = 1;
    if (driveOut & 0x08) L2H = 0;
    if (driveOut & 0x10) L3L = 1;
    if (driveOut & 0x20) L3H = 0;
    }
    
    //Convert photointerrupter inputs to a rotor state
inline int8_t readRotorState(){
    return stateMap[I1 + 2*I2 + 4*I3];
    }

//Basic synchronisation routine    
int8_t motorHome() {
    //Put the motor in drive state 0 and wait for it to stabilise
    motorOut(0);
    wait(2.0);
    
    //Get the rotor state
    return readRotorState();
}
    
//Main
int main() {
    int8_t orState = 0;    //Rotot offset at motor state 0
    int8_t intState = 0;
    int8_t intStateOld = 0;
    
    //Initialise the serial port
    Serial pc(SERIAL_TX, SERIAL_RX);
    pc.printf("Hello\n\r");
    
    //Run the motor synchronisation
    orState = motorHome();
    pc.printf("Rotor origin: %x\n\r",orState);
    //orState is subtracted from future rotor state inputs to align rotor and motor states
    
    //Poll the rotor state and set the motor outputs accordingly to spin the motor
    while (1) {
        intState = readRotorState();
        if (intState != intStateOld) {
            intStateOld = intState;
            motorOut((intState-orState+lead+6)%6); //+6 to make sure the remainder is positive
            //pc.printf("%d\n\r",intState);
        }
    }
}