ISEN Nimes CSI3
no modif
Dependents: ISEN_RF24Network_Node_01 ISEN_RF24Network_Node_02
RF24.h
- Committer:
- akashvibhute
- Date:
- 2015-12-30
- Revision:
- 4:a35313611c1c
- Parent:
- 3:e94be00fd19e
- Child:
- 6:5cc7136648d1
File content as of revision 4:a35313611c1c:
/*
Copyright (C) 2011 J. Coliz <maniacbug@ymail.com>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
version 2 as published by the Free Software Foundation.
*/
/*
* Mbed support added by Akash Vibhute <akash.roboticist@gmail.com>
* Porting completed on Nov/05/2015
*
* Updated with TMRh20's RF24 library on Nov/04/2015 from https://github.com/TMRh20
*
*/
/**
* @file RF24.h
*
* Class declaration for RF24 and helper enums
*/
#ifndef __RF24_H__
#define __RF24_H__
#include "RF24_config.h"
#define HIGH 1
#define LOW 0
#include <mbed.h>
/**
* Power Amplifier level.
*
* For use with setPALevel()
*/
typedef enum { RF24_PA_MIN = 0,RF24_PA_LOW, RF24_PA_HIGH, RF24_PA_MAX, RF24_PA_ERROR } rf24_pa_dbm_e ;
/**
* Data rate. How fast data moves through the air.
*
* For use with setDataRate()
*/
typedef enum { RF24_1MBPS = 0, RF24_2MBPS, RF24_250KBPS } rf24_datarate_e;
/**
* CRC Length. How big (if any) of a CRC is included.
*
* For use with setCRCLength()
*/
typedef enum { RF24_CRC_DISABLED = 0, RF24_CRC_8, RF24_CRC_16 } rf24_crclength_e;
/**
* Driver for nRF24L01(+) 2.4GHz Wireless Transceiver
*/
class RF24
{
private:
SPI spi;
Timer mainTimer;
DigitalOut ce_pin; /**< "Chip Enable" pin, activates the RX or TX role */
DigitalOut csn_pin; /**< SPI Chip select */
bool p_variant; /* False for RF24L01 and true for RF24L01P */
uint8_t payload_size; /**< Fixed size of payloads */
bool dynamic_payloads_enabled; /**< Whether dynamic payloads are enabled. */
uint8_t pipe0_reading_address[5]; /**< Last address set on pipe 0 for reading. */
uint8_t addr_width; /**< The address width to use - 3,4 or 5 bytes. */
uint32_t txRxDelay; /**< Var for adjusting delays depending on datarate */
protected:
/**
* SPI transactions
*
* Common code for SPI transactions including CSN toggle
*
*/
inline void beginTransaction();
inline void endTransaction();
public:
/**
* @name Primary public interface
*
* These are the main methods you need to operate the chip
*/
/**@{*/
RF24(PinName mosi, PinName miso, PinName sck, PinName _cepin, PinName _csnpin);
/**
* Begin operation of the chip
*
* Call this in setup(), before calling any other methods.
* @code radio.begin() @endcode
*/
bool begin(void);
/**
* Start listening on the pipes opened for reading.
*
* 1. Be sure to call openReadingPipe() first.
* 2. Do not call write() while in this mode, without first calling stopListening().
* 3. Call available() to check for incoming traffic, and read() to get it.
*
* @code
* Open reading pipe 1 using address CCCECCCECC
*
* byte address[] = { 0xCC,0xCE,0xCC,0xCE,0xCC };
* radio.openReadingPipe(1,address);
* radio.startListening();
* @endcode
*/
void startListening(void);
/**
* Stop listening for incoming messages, and switch to transmit mode.
*
* Do this before calling write().
* @code
* radio.stopListening();
* radio.write(&data,sizeof(data));
* @endcode
*/
void stopListening(void);
/**
* Check whether there are bytes available to be read
* @code
* if(radio.available()){
* radio.read(&data,sizeof(data));
* }
* @endcode
* @return True if there is a payload available, false if none is
*/
bool available(void);
/**
* Read the available payload
*
* The size of data read is the fixed payload size, see getPayloadSize()
*
* @note I specifically chose 'void*' as a data type to make it easier
* for beginners to use. No casting needed.
*
* @note No longer boolean. Use available to determine if packets are
* available. Interrupt flags are now cleared during reads instead of
* when calling available().
*
* @param buf Pointer to a buffer where the data should be written
* @param len Maximum number of bytes to read into the buffer
*
* @code
* if(radio.available()){
* radio.read(&data,sizeof(data));
* }
* @endcode
* @return No return value. Use available().
*/
void read( void* buf, uint8_t len );
/**
* Be sure to call openWritingPipe() first to set the destination
* of where to write to.
*
* This blocks until the message is successfully acknowledged by
* the receiver or the timeout/retransmit maxima are reached. In
* the current configuration, the max delay here is 60-70ms.
*
* The maximum size of data written is the fixed payload size, see
* getPayloadSize(). However, you can write less, and the remainder
* will just be filled with zeroes.
*
* TX/RX/RT interrupt flags will be cleared every time write is called
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
*
* @code
* radio.stopListening();
* radio.write(&data,sizeof(data));
* @endcode
* @return True if the payload was delivered successfully false if not
*/
bool write( const void* buf, uint8_t len );
/**
* New: Open a pipe for writing via byte array. Old addressing format retained
* for compatibility.
*
* Only one writing pipe can be open at once, but you can change the address
* you'll write to. Call stopListening() first.
*
* Addresses are assigned via a byte array, default is 5 byte address length
s *
* @code
* uint8_t addresses[][6] = {"1Node","2Node"};
* radio.openWritingPipe(addresses[0]);
* @endcode
* @code
* uint8_t address[] = { 0xCC,0xCE,0xCC,0xCE,0xCC };
* radio.openWritingPipe(address);
* address[0] = 0x33;
* radio.openReadingPipe(1,address);
* @endcode
* @see setAddressWidth
*
* @param address The address of the pipe to open. Coordinate these pipe
* addresses amongst nodes on the network.
*/
void openWritingPipe(const uint8_t *address);
/**
* Open a pipe for reading
*
* Up to 6 pipes can be open for reading at once. Open all the required
* reading pipes, and then call startListening().
*
* @see openWritingPipe
* @see setAddressWidth
*
* @note Pipes 0 and 1 will store a full 5-byte address. Pipes 2-5 will technically
* only store a single byte, borrowing up to 4 additional bytes from pipe #1 per the
* assigned address width.
* @warning Pipes 1-5 should share the same address, except the first byte.
* Only the first byte in the array should be unique, e.g.
* @code
* uint8_t addresses[][6] = {"1Node","2Node"};
* openReadingPipe(1,addresses[0]);
* openReadingPipe(2,addresses[1]);
* @endcode
*
* @warning Pipe 0 is also used by the writing pipe. So if you open
* pipe 0 for reading, and then startListening(), it will overwrite the
* writing pipe. Ergo, do an openWritingPipe() again before write().
*
* @param number Which pipe# to open, 0-5.
* @param address The 24, 32 or 40 bit address of the pipe to open.
*/
void openReadingPipe(uint8_t number, const uint8_t *address);
/**@}*/
/**
* @name Advanced Operation
*
* Methods you can use to drive the chip in more advanced ways
*/
/**@{*/
/**
* Print a giant block of debugging information to stdout
*
* @warning Does nothing if stdout is not defined. See fdevopen in stdio.h
* The printf.h file is included with the library for Arduino.
* @code
* #include <printf.h>
* setup(){
* Serial.begin(115200);
* printf_begin();
* ...
* }
* @endcode
*/
void printDetails(void);
/**
* Test whether there are bytes available to be read in the
* FIFO buffers.
*
* @param[out] pipe_num Which pipe has the payload available
*
* @code
* uint8_t pipeNum;
* if(radio.available(&pipeNum)){
* radio.read(&data,sizeof(data));
* Serial.print("Got data on pipe");
* Serial.println(pipeNum);
* }
* @endcode
* @return True if there is a payload available, false if none is
*/
bool available(uint8_t* pipe_num);
/**
* Check if the radio needs to be read. Can be used to prevent data loss
* @return True if all three 32-byte radio buffers are full
*/
bool rxFifoFull();
/**
* Enter low-power mode
*
* To return to normal power mode, call powerUp().
*
* @note After calling startListening(), a basic radio will consume about 13.5mA
* at max PA level.
* During active transmission, the radio will consume about 11.5mA, but this will
* be reduced to 26uA (.026mA) between sending.
* In full powerDown mode, the radio will consume approximately 900nA (.0009mA)
*
* @code
* radio.powerDown();
* avr_enter_sleep_mode(); // Custom function to sleep the device
* radio.powerUp();
* @endcode
*/
void powerDown(void);
/**
* Leave low-power mode - required for normal radio operation after calling powerDown()
*
* To return to low power mode, call powerDown().
* @note This will take up to 5ms for maximum compatibility
*/
void powerUp(void) ;
/**
* Write for single NOACK writes. Optionally disables acknowledgements/autoretries for a single write.
*
* @note enableDynamicAck() must be called to enable this feature
*
* Can be used with enableAckPayload() to request a response
* @see enableDynamicAck()
* @see setAutoAck()
* @see write()
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @param multicast Request ACK (0), NOACK (1)
*/
bool write( const void* buf, uint8_t len, const bool multicast );
/**
* This will not block until the 3 FIFO buffers are filled with data.
* Once the FIFOs are full, writeFast will simply wait for success or
* timeout, and return 1 or 0 respectively. From a user perspective, just
* keep trying to send the same data. The library will keep auto retrying
* the current payload using the built in functionality.
* @warning It is important to never keep the nRF24L01 in TX mode and FIFO full for more than 4ms at a time. If the auto
* retransmit is enabled, the nRF24L01 is never in TX mode long enough to disobey this rule. Allow the FIFO
* to clear by issuing txStandBy() or ensure appropriate time between transmissions.
*
* @code
* Example (Partial blocking):
*
* radio.writeFast(&buf,32); // Writes 1 payload to the buffers
* txStandBy(); // Returns 0 if failed. 1 if success. Blocks only until MAX_RT timeout or success. Data flushed on fail.
*
* radio.writeFast(&buf,32); // Writes 1 payload to the buffers
* txStandBy(1000); // Using extended timeouts, returns 1 if success. Retries failed payloads for 1 seconds before returning 0.
* @endcode
*
* @see txStandBy()
* @see write()
* @see writeBlocking()
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @return True if the payload was delivered successfully false if not
*/
bool writeFast( const void* buf, uint8_t len );
/**
* WriteFast for single NOACK writes. Disables acknowledgements/autoretries for a single write.
*
* @note enableDynamicAck() must be called to enable this feature
* @see enableDynamicAck()
* @see setAutoAck()
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @param multicast Request ACK (0) or NOACK (1)
*/
bool writeFast( const void* buf, uint8_t len, const bool multicast );
/**
* This function extends the auto-retry mechanism to any specified duration.
* It will not block until the 3 FIFO buffers are filled with data.
* If so the library will auto retry until a new payload is written
* or the user specified timeout period is reached.
* @warning It is important to never keep the nRF24L01 in TX mode and FIFO full for more than 4ms at a time. If the auto
* retransmit is enabled, the nRF24L01 is never in TX mode long enough to disobey this rule. Allow the FIFO
* to clear by issuing txStandBy() or ensure appropriate time between transmissions.
*
* @code
* Example (Full blocking):
*
* radio.writeBlocking(&buf,32,1000); //Wait up to 1 second to write 1 payload to the buffers
* txStandBy(1000); //Wait up to 1 second for the payload to send. Return 1 if ok, 0 if failed.
* //Blocks only until user timeout or success. Data flushed on fail.
* @endcode
* @note If used from within an interrupt, the interrupt should be disabled until completion, and sei(); called to enable millis().
* @see txStandBy()
* @see write()
* @see writeFast()
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @param timeout User defined timeout in milliseconds.
* @return True if the payload was loaded into the buffer successfully false if not
*/
bool writeBlocking( const void* buf, uint8_t len, uint32_t timeout );
/**
* This function should be called as soon as transmission is finished to
* drop the radio back to STANDBY-I mode. If not issued, the radio will
* remain in STANDBY-II mode which, per the data sheet, is not a recommended
* operating mode.
*
* @note When transmitting data in rapid succession, it is still recommended by
* the manufacturer to drop the radio out of TX or STANDBY-II mode if there is
* time enough between sends for the FIFOs to empty. This is not required if auto-ack
* is enabled.
*
* Relies on built-in auto retry functionality.
*
* @code
* Example (Partial blocking):
*
* radio.writeFast(&buf,32);
* radio.writeFast(&buf,32);
* radio.writeFast(&buf,32); //Fills the FIFO buffers up
* bool ok = txStandBy(); //Returns 0 if failed. 1 if success.
* //Blocks only until MAX_RT timeout or success. Data flushed on fail.
* @endcode
* @see txStandBy(unsigned long timeout)
* @return True if transmission is successful
*
*/
bool txStandBy();
/**
* This function allows extended blocking and auto-retries per a user defined timeout
* @code
* Fully Blocking Example:
*
* radio.writeFast(&buf,32);
* radio.writeFast(&buf,32);
* radio.writeFast(&buf,32); //Fills the FIFO buffers up
* bool ok = txStandBy(1000); //Returns 0 if failed after 1 second of retries. 1 if success.
* //Blocks only until user defined timeout or success. Data flushed on fail.
* @endcode
* @note If used from within an interrupt, the interrupt should be disabled until completion, and sei(); called to enable millis().
* @param timeout Number of milliseconds to retry failed payloads
* @return True if transmission is successful
*
*/
bool txStandBy(uint32_t timeout, bool startTx = 0);
/**
* Write an ack payload for the specified pipe
*
* The next time a message is received on @p pipe, the data in @p buf will
* be sent back in the acknowledgement.
* @see enableAckPayload()
* @see enableDynamicPayloads()
* @warning Only three of these can be pending at any time as there are only 3 FIFO buffers.<br> Dynamic payloads must be enabled.
* @note Ack payloads are handled automatically by the radio chip when a payload is received. Users should generally
* write an ack payload as soon as startListening() is called, so one is available when a regular payload is received.
* @note Ack payloads are dynamic payloads. This only works on pipes 0&1 by default. Call
* enableDynamicPayloads() to enable on all pipes.
*
* @param pipe Which pipe# (typically 1-5) will get this response.
* @param buf Pointer to data that is sent
* @param len Length of the data to send, up to 32 bytes max. Not affected
* by the static payload set by setPayloadSize().
*/
void writeAckPayload(uint8_t pipe, const void* buf, uint8_t len);
/**
* Determine if an ack payload was received in the most recent call to
* write(). The regular available() can also be used.
*
* Call read() to retrieve the ack payload.
*
* @return True if an ack payload is available.
*/
bool isAckPayloadAvailable(void);
/**
* Call this when you get an interrupt to find out why
*
* Tells you what caused the interrupt, and clears the state of
* interrupts.
*
* @param[out] tx_ok The send was successful (TX_DS)
* @param[out] tx_fail The send failed, too many retries (MAX_RT)
* @param[out] rx_ready There is a message waiting to be read (RX_DS)
*/
void whatHappened(bool& tx_ok,bool& tx_fail,bool& rx_ready);
/**
* Non-blocking write to the open writing pipe used for buffered writes
*
* @note Optimization: This function now leaves the CE pin high, so the radio
* will remain in TX or STANDBY-II Mode until a txStandBy() command is issued. Can be used as an alternative to startWrite()
* if writing multiple payloads at once.
* @warning It is important to never keep the nRF24L01 in TX mode with FIFO full for more than 4ms at a time. If the auto
* retransmit/autoAck is enabled, the nRF24L01 is never in TX mode long enough to disobey this rule. Allow the FIFO
* to clear by issuing txStandBy() or ensure appropriate time between transmissions.
*
* @see write()
* @see writeFast()
* @see startWrite()
* @see writeBlocking()
*
* For single noAck writes see:
* @see enableDynamicAck()
* @see setAutoAck()
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @param multicast Request ACK (0) or NOACK (1)
* @return True if the payload was delivered successfully false if not
*/
void startFastWrite( const void* buf, uint8_t len, const bool multicast, bool startTx = 1 );
/**
* Non-blocking write to the open writing pipe
*
* Just like write(), but it returns immediately. To find out what happened
* to the send, catch the IRQ and then call whatHappened().
*
* @see write()
* @see writeFast()
* @see startFastWrite()
* @see whatHappened()
*
* For single noAck writes see:
* @see enableDynamicAck()
* @see setAutoAck()
*
* @param buf Pointer to the data to be sent
* @param len Number of bytes to be sent
* @param multicast Request ACK (0) or NOACK (1)
*
*/
void startWrite( const void* buf, uint8_t len, const bool multicast );
/**
* This function is mainly used internally to take advantage of the auto payload
* re-use functionality of the chip, but can be beneficial to users as well.
*
* The function will instruct the radio to re-use the data in the FIFO buffers,
* and instructs the radio to re-send once the timeout limit has been reached.
* Used by writeFast and writeBlocking to initiate retries when a TX failure
* occurs. Retries are automatically initiated except with the standard write().
* This way, data is not flushed from the buffer until switching between modes.
*
* @note This is to be used AFTER auto-retry fails if wanting to resend
* using the built-in payload reuse features.
* After issuing reUseTX(), it will keep reending the same payload forever or until
* a payload is written to the FIFO, or a flush_tx command is given.
*/
void reUseTX();
/**
* Empty the transmit buffer. This is generally not required in standard operation.
* May be required in specific cases after stopListening() , if operating at 250KBPS data rate.
*
* @return Current value of status register
*/
uint8_t flush_tx(void);
/**
* Test whether there was a carrier on the line for the
* previous listening period.
*
* Useful to check for interference on the current channel.
*
* @return true if was carrier, false if not
*/
bool testCarrier(void);
/**
* Test whether a signal (carrier or otherwise) greater than
* or equal to -64dBm is present on the channel. Valid only
* on nRF24L01P (+) hardware. On nRF24L01, use testCarrier().
*
* Useful to check for interference on the current channel and
* channel hopping strategies.
*
* @code
* bool goodSignal = radio.testRPD();
* if(radio.available()){
* Serial.println(goodSignal ? "Strong signal > 64dBm" : "Weak signal < 64dBm" );
* radio.read(0,0);
* }
* @endcode
* @return true if signal => -64dBm, false if not
*/
bool testRPD(void) ;
/**
* Test whether this is a real radio, or a mock shim for
* debugging. Setting either pin to 0xff is the way to
* indicate that this is not a real radio.
*
* @return true if this is a legitimate radio
*/
bool isValid() {
return ce_pin != 0xff && csn_pin != 0xff;
}
/**
* Close a pipe after it has been previously opened.
* Can be safely called without having previously opened a pipe.
* @param pipe Which pipe # to close, 0-5.
*/
void closeReadingPipe( uint8_t pipe ) ;
/**
* Enable error detection by un-commenting #define FAILURE_HANDLING in RF24_config.h
* If a failure has been detected, it usually indicates a hardware issue. By default the library
* will cease operation when a failure is detected.
* This should allow advanced users to detect and resolve intermittent hardware issues.
*
* In most cases, the radio must be re-enabled via radio.begin(); and the appropriate settings
* applied after a failure occurs, if wanting to re-enable the device immediately.
*
* Usage: (Failure handling must be enabled per above)
* @code
* if(radio.failureDetected){
* radio.begin(); // Attempt to re-configure the radio with defaults
* radio.failureDetected = 0; // Reset the detection value
* radio.openWritingPipe(addresses[1]); // Re-configure pipe addresses
* radio.openReadingPipe(1,addresses[0]);
* report_failure(); // Blink leds, send a message, etc. to indicate failure
* }
* @endcode
*/
//#if defined (FAILURE_HANDLING)
bool failureDetected;
//#endif
/**@}*/
/**@}*/
/**
* @name Optional Configurators
*
* Methods you can use to get or set the configuration of the chip.
* None are required. Calling begin() sets up a reasonable set of
* defaults.
*/
/**@{*/
/**
* Set the address width from 3 to 5 bytes (24, 32 or 40 bit)
*
* @param a_width The address width to use: 3,4 or 5
*/
void setAddressWidth(uint8_t a_width);
/**
* Set the number and delay of retries upon failed submit
*
* @param delay How long to wait between each retry, in multiples of 250us,
* max is 15. 0 means 250us, 15 means 4000us.
* @param count How many retries before giving up, max 15
*/
void setRetries(uint8_t delay, uint8_t count);
/**
* Set RF communication channel
*
* @param channel Which RF channel to communicate on, 0-127
*/
void setChannel(uint8_t channel);
/**
* Get RF communication channel
*
* @return The currently configured RF Channel
*/
uint8_t getChannel(void);
/**
* Set Static Payload Size
*
* This implementation uses a pre-stablished fixed payload size for all
* transmissions. If this method is never called, the driver will always
* transmit the maximum payload size (32 bytes), no matter how much
* was sent to write().
*
* @todo Implement variable-sized payloads feature
*
* @param size The number of bytes in the payload
*/
void setPayloadSize(uint8_t size);
/**
* Get Static Payload Size
*
* @see setPayloadSize()
*
* @return The number of bytes in the payload
*/
uint8_t getPayloadSize(void);
/**
* Get Dynamic Payload Size
*
* For dynamic payloads, this pulls the size of the payload off
* the chip
*
* @note Corrupt packets are now detected and flushed per the
* manufacturer.
* @code
* if(radio.available()){
* if(radio.getDynamicPayloadSize() < 1){
* // Corrupt payload has been flushed
* return;
* }
* radio.read(&data,sizeof(data));
* }
* @endcode
*
* @return Payload length of last-received dynamic payload
*/
uint8_t getDynamicPayloadSize(void);
/**
* Enable custom payloads on the acknowledge packets
*
* Ack payloads are a handy way to return data back to senders without
* manually changing the radio modes on both units.
*
* @note Ack payloads are dynamic payloads. This only works on pipes 0&1 by default. Call
* enableDynamicPayloads() to enable on all pipes.
*/
void enableAckPayload(void);
/**
* Enable dynamically-sized payloads
*
* This way you don't always have to send large packets just to send them
* once in a while. This enables dynamic payloads on ALL pipes.
*
*/
void enableDynamicPayloads(void);
/**
* Enable dynamic ACKs (single write multicast or unicast) for chosen messages
*
* @note To enable full multicast or per-pipe multicast, use setAutoAck()
*
* @warning This MUST be called prior to attempting single write NOACK calls
* @code
* radio.enableDynamicAck();
* radio.write(&data,32,1); // Sends a payload with no acknowledgement requested
* radio.write(&data,32,0); // Sends a payload using auto-retry/autoACK
* @endcode
*/
void enableDynamicAck();
/**
* Determine whether the hardware is an nRF24L01+ or not.
*
* @return true if the hardware is nRF24L01+ (or compatible) and false
* if its not.
*/
bool isPVariant(void) ;
/**
* Enable or disable auto-acknowlede packets
*
* This is enabled by default, so it's only needed if you want to turn
* it off for some reason.
*
* @param enable Whether to enable (true) or disable (false) auto-acks
*/
void setAutoAck(bool enable);
/**
* Enable or disable auto-acknowlede packets on a per pipeline basis.
*
* AA is enabled by default, so it's only needed if you want to turn
* it off/on for some reason on a per pipeline basis.
*
* @param pipe Which pipeline to modify
* @param enable Whether to enable (true) or disable (false) auto-acks
*/
void setAutoAck( uint8_t pipe, bool enable ) ;
/**
* Set Power Amplifier (PA) level to one of four levels:
* RF24_PA_MIN, RF24_PA_LOW, RF24_PA_HIGH and RF24_PA_MAX
*
* The power levels correspond to the following output levels respectively:
* NRF24L01: -18dBm, -12dBm,-6dBM, and 0dBm
*
* SI24R1: -6dBm, 0dBm, 3dBM, and 7dBm.
*
* @param level Desired PA level.
*/
void setPALevel ( uint8_t level );
/**
* Fetches the current PA level.
*
* NRF24L01: -18dBm, -12dBm, -6dBm and 0dBm
* SI24R1: -6dBm, 0dBm, 3dBm, 7dBm
*
* @return Returns values 0 to 3 representing the PA Level.
*/
uint8_t getPALevel( void );
/**
* Set the transmission data rate
*
* @warning setting RF24_250KBPS will fail for non-plus units
*
* @param speed RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS for 2Mbps
* @return true if the change was successful
*/
bool setDataRate(rf24_datarate_e speed);
/**
* Fetches the transmission data rate
*
* @return Returns the hardware's currently configured datarate. The value
* is one of 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS, as defined in the
* rf24_datarate_e enum.
*/
rf24_datarate_e getDataRate( void ) ;
/**
* Set the CRC length
*
* @param length RF24_CRC_8 for 8-bit or RF24_CRC_16 for 16-bit
*/
void setCRCLength(rf24_crclength_e length);
/**
* Get the CRC length
*
* @return RF24_DISABLED if disabled or RF24_CRC_8 for 8-bit or RF24_CRC_16 for 16-bit
*/
rf24_crclength_e getCRCLength(void);
/**
* Disable CRC validation
*
* @warning CRC cannot be disabled if auto-ack/ESB is enabled.
*/
void disableCRC( void ) ;
/**
* The radio will generate interrupt signals when a transmission is complete,
* a transmission fails, or a payload is received. This allows users to mask
* those interrupts to prevent them from generating a signal on the interrupt
* pin. Interrupts are enabled on the radio chip by default.
*
* @code
* Mask all interrupts except the receive interrupt:
*
* radio.maskIRQ(1,1,0);
* @endcode
*
* @param tx_ok Mask transmission complete interrupts
* @param tx_fail Mask transmit failure interrupts
* @param rx_ready Mask payload received interrupts
*/
void maskIRQ(bool tx_ok,bool tx_fail,bool rx_ready);
/**@}*/
/**
* @name Deprecated
*
* Methods provided for backwards compabibility.
*/
/**@{*/
/**
* Open a pipe for reading
* @note For compatibility with old code only, see new function
*
* @warning Pipes 1-5 should share the first 32 bits.
* Only the least significant byte should be unique, e.g.
* @code
* openReadingPipe(1,0xF0F0F0F0AA);
* openReadingPipe(2,0xF0F0F0F066);
* @endcode
*
* @warning Pipe 0 is also used by the writing pipe. So if you open
* pipe 0 for reading, and then startListening(), it will overwrite the
* writing pipe. Ergo, do an openWritingPipe() again before write().
*
* @param number Which pipe# to open, 0-5.
* @param address The 40-bit address of the pipe to open.
*/
void openReadingPipe(uint8_t number, uint64_t address);
/**
* Open a pipe for writing
* @note For compatibility with old code only, see new function
*
* Addresses are 40-bit hex values, e.g.:
*
* @code
* openWritingPipe(0xF0F0F0F0F0);
* @endcode
*
* @param address The 40-bit address of the pipe to open.
*/
void openWritingPipe(uint64_t address);
private:
/**
* @name Low-level internal interface.
*
* Protected methods that address the chip directly. Regular users cannot
* ever call these. They are documented for completeness and for developers who
* may want to extend this class.
*/
/**@{*/
/**
* Set chip select pin
*
* Running SPI bus at PI_CLOCK_DIV2 so we don't waste time transferring data
* and best of all, we make use of the radio's FIFO buffers. A lower speed
* means we're less likely to effectively leverage our FIFOs and pay a higher
* AVR runtime cost as toll.
*
* @param mode HIGH to take this unit off the SPI bus, LOW to put it on
*/
void csn(bool mode);
/**
* Set chip enable
*
* @param level HIGH to actively begin transmission or LOW to put in standby. Please see data sheet
* for a much more detailed description of this pin.
*/
void ce(bool level);
/**
* Read a chunk of data in from a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @param buf Where to put the data
* @param len How many bytes of data to transfer
* @return Current value of status register
*/
uint8_t read_register(uint8_t reg, uint8_t* buf, uint8_t len);
/**
* Read single byte from a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @return Current value of register @p reg
*/
uint8_t read_register(uint8_t reg);
/**
* Write a chunk of data to a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @param buf Where to get the data
* @param len How many bytes of data to transfer
* @return Current value of status register
*/
uint8_t write_register(uint8_t reg, const uint8_t* buf, uint8_t len);
/**
* Write a single byte to a register
*
* @param reg Which register. Use constants from nRF24L01.h
* @param value The new value to write
* @return Current value of status register
*/
uint8_t write_register(uint8_t reg, uint8_t value);
/**
* Write the transmit payload
*
* The size of data written is the fixed payload size, see getPayloadSize()
*
* @param buf Where to get the data
* @param len Number of bytes to be sent
* @return Current value of status register
*/
uint8_t write_payload(const void* buf, uint8_t len, const uint8_t writeType);
/**
* Read the receive payload
*
* The size of data read is the fixed payload size, see getPayloadSize()
*
* @param buf Where to put the data
* @param len Maximum number of bytes to read
* @return Current value of status register
*/
uint8_t read_payload(void* buf, uint8_t len);
/**
* Empty the receive buffer
*
* @return Current value of status register
*/
uint8_t flush_rx(void);
/**
* Retrieve the current status of the chip
*
* @return Current value of status register
*/
uint8_t get_status(void);
#if !defined (MINIMAL)
/**
* Decode and print the given status to stdout
*
* @param status Status value to print
*
* @warning Does nothing if stdout is not defined. See fdevopen in stdio.h
*/
void print_status(uint8_t status);
/**
* Decode and print the given 'observe_tx' value to stdout
*
* @param value The observe_tx value to print
*
* @warning Does nothing if stdout is not defined. See fdevopen in stdio.h
*/
void print_observe_tx(uint8_t value);
/**
* Print the name and value of an 8-bit register to stdout
*
* Optionally it can print some quantity of successive
* registers on the same line. This is useful for printing a group
* of related registers on one line.
*
* @param name Name of the register
* @param reg Which register. Use constants from nRF24L01.h
* @param qty How many successive registers to print
*/
void print_byte_register(const char* name, uint8_t reg, uint8_t qty = 1);
/**
* Print the name and value of a 40-bit address register to stdout
*
* Optionally it can print some quantity of successive
* registers on the same line. This is useful for printing a group
* of related registers on one line.
*
* @param name Name of the register
* @param reg Which register. Use constants from nRF24L01.h
* @param qty How many successive registers to print
*/
void print_address_register(const char* name, uint8_t reg, uint8_t qty = 1);
#endif
/**
* Turn on or off the special features of the chip
*
* The chip has certain 'features' which are only available when the 'features'
* are enabled. See the datasheet for details.
*/
void toggle_features(void);
/**
* Built in spi transfer function to simplify repeating code repeating code
*/
uint8_t spiTrans(uint8_t cmd);
#if defined (FAILURE_HANDLING) || defined (RF24_LINUX)
void errNotify(void);
#endif
/**@}*/
};
/**
* @example GettingStarted.ino
* <b>For Arduino</b><br>
* <b>Updated: TMRh20 2014 </b><br>
*
* This is an example of how to use the RF24 class to communicate on a basic level. Configure and write this sketch to two
* different nodes. Put one of the nodes into 'transmit' mode by connecting with the serial monitor and <br>
* sending a 'T'. The ping node sends the current time to the pong node, which responds by sending the value
* back. The ping node can then see how long the whole cycle took. <br>
* @note For a more efficient call-response scenario see the GettingStarted_CallResponse.ino example.
* @note When switching between sketches, the radio may need to be powered down to clear settings that are not "un-set" otherwise
*/
/**
* @example GettingStarted.cpp
* <b>For Raspberry Pi</b><br>
* <b>Updated: TMRh20 2014 </b><br>
*
* This is an example of how to use the RF24 class to communicate on a basic level. Configure and write this sketch to two
* different nodes. Put one of the nodes into 'transmit' mode by connecting with the serial monitor and <br>
* sending a 'T'. The ping node sends the current time to the pong node, which responds by sending the value
* back. The ping node can then see how long the whole cycle took. <br>
* @note For a more efficient call-response scenario see the GettingStarted_CallResponse.ino example.
*/
/**
* @example GettingStarted_CallResponse.ino
* <b>For Arduino</b><br>
* <b>New: TMRh20 2014</b><br>
*
* This example continues to make use of all the normal functionality of the radios including
* the auto-ack and auto-retry features, but allows ack-payloads to be written optionlly as well. <br>
* This allows very fast call-response communication, with the responding radio never having to
* switch out of Primary Receiver mode to send back a payload, but having the option to switch to <br>
* primary transmitter if wanting to initiate communication instead of respond to a commmunication.
*/
/**
* @example GettingStarted_Call_Response.cpp
* <b>For Raspberry Pi</b><br>
* <b>New: TMRh20 2014</b><br>
*
* This example continues to make use of all the normal functionality of the radios including
* the auto-ack and auto-retry features, but allows ack-payloads to be written optionlly as well. <br>
* This allows very fast call-response communication, with the responding radio never having to
* switch out of Primary Receiver mode to send back a payload, but having the option to switch to <br>
* primary transmitter if wanting to initiate communication instead of respond to a commmunication.
*/
/**
* @example GettingStarted_HandlingData.ino
* <b>Dec 2014 - TMRh20</b><br>
*
* This example demonstrates how to send multiple variables in a single payload and work with data. As usual, it is
* generally important to include an incrementing value like millis() in the payloads to prevent errors.
*/
/**
* @example Transfer.ino
* <b>For Arduino</b><br>
* This example demonstrates half-rate transfer using the FIFO buffers<br>
*
* It is an example of how to use the RF24 class. Write this sketch to two
* different nodes. Put one of the nodes into 'transmit' mode by connecting <br>
* with the serial monitor and sending a 'T'. The data transfer will begin,
* with the receiver displaying the payload count. (32Byte Payloads) <br>
*/
/**
* @example Transfer.cpp
* <b>For Raspberry Pi</b><br>
* This example demonstrates half-rate transfer using the FIFO buffers<br>
*
* It is an example of how to use the RF24 class. Write this sketch to two
* different nodes. Put one of the nodes into 'transmit' mode by connecting <br>
* with the serial monitor and sending a 'T'. The data transfer will begin,
* with the receiver displaying the payload count. (32Byte Payloads) <br>
*/
/**
* @example TransferTimeouts.ino
* <b>New: TMRh20 </b><br>
* This example demonstrates the use of and extended timeout period and
* auto-retries/auto-reUse to increase reliability in noisy or low signal scenarios. <br>
*
* Write this sketch to two different nodes. Put one of the nodes into 'transmit'
* mode by connecting with the serial monitor and sending a 'T'. The data <br>
* transfer will begin, with the receiver displaying the payload count and the
* data transfer rate.
*/
/**
* @example starping.pde
*
* This sketch is a more complex example of using the RF24 library for Arduino.
* Deploy this on up to six nodes. Set one as the 'pong receiver' by tying the
* role_pin low, and the others will be 'ping transmit' units. The ping units
* unit will send out the value of millis() once a second. The pong unit will
* respond back with a copy of the value. Each ping unit can get that response
* back, and determine how long the whole cycle took.
*
* This example requires a bit more complexity to determine which unit is which.
* The pong receiver is identified by having its role_pin tied to ground.
* The ping senders are further differentiated by a byte in eeprom.
*/
/**
* @example pingpair_ack.ino
* <b>Update: TMRh20</b><br>
* This example continues to make use of all the normal functionality of the radios including
* the auto-ack and auto-retry features, but allows ack-payloads to be written optionlly as well.<br>
* This allows very fast call-response communication, with the responding radio never having to
* switch out of Primary Receiver mode to send back a payload, but having the option to if wanting<br>
* to initiate communication instead of respond to a commmunication.
*/
/**
* @example pingpair_irq.ino
* <b>Update: TMRh20</b><br>
* This is an example of how to user interrupts to interact with the radio, and a demonstration
* of how to use them to sleep when receiving, and not miss any payloads.<br>
* The pingpair_sleepy example expands on sleep functionality with a timed sleep option for the transmitter.
* Sleep functionality is built directly into my fork of the RF24Network library<br>
*/
/**
* @example pingpair_irq_simple.ino
* <b>Dec 2014 - TMRh20</b><br>
* This is an example of how to user interrupts to interact with the radio, with bidirectional communication.
*/
/**
* @example pingpair_sleepy.ino
* <b>Update: TMRh20</b><br>
* This is an example of how to use the RF24 class to create a battery-
* efficient system. It is just like the GettingStarted_CallResponse example, but the<br>
* ping node powers down the radio and sleeps the MCU after every
* ping/pong cycle, and the receiver sleeps between payloads. <br>
*/
/**
* @example rf24ping85.ino
* <b>New: Contributed by https://github.com/tong67</b><br>
* This is an example of how to use the RF24 class to communicate with ATtiny85 and other node. <br>
*/
/**
* @example timingSearch3pin.ino
* <b>New: Contributed by https://github.com/tong67</b><br>
* This is an example of how to determine the correct timing for ATtiny when using only 3-pins
*/
/**
* @example pingpair_dyn.ino
*
* This is an example of how to use payloads of a varying (dynamic) size on Arduino.
*/
/**
* @example pingpair_dyn.cpp
*
* This is an example of how to use payloads of a varying (dynamic) size on Raspberry Pi.
*/
/**
* @example pingpair_dyn.py
*
* This is a python example for RPi of how to use payloads of a varying (dynamic) size.
*/
/**
* @example pingpair_dyn.ino
*
* This is an example of how to use payloads of a varying (dynamic) size.
*/
/**
* @example pingpair_dyn.ino
*
* This is an example of how to use payloads of a varying (dynamic) size.
*/
/**
* @example scanner.ino
*
* Example to detect interference on the various channels available.
* This is a good diagnostic tool to check whether you're picking a
* good channel for your application.
*
* Inspired by cpixip.
* See http://arduino.cc/forum/index.php/topic,54795.0.html
*/
/**
* @mainpage Optimized High Speed Driver for nRF24L01(+) 2.4GHz Wireless Transceiver
*
* @section Goals Design Goals
*
* This library fork is designed to be...
* @li More compliant with the manufacturer specified operation of the chip, while allowing advanced users
* to work outside the recommended operation.
* @li Utilize the capabilities of the radio to their full potential via Arduino
* @li More reliable, responsive, bug-free and feature rich
* @li Easy for beginners to use, with well documented examples and features
* @li Consumed with a public interface that's similar to other Arduino standard libraries
*
* @section News News
*
* **March 2015**<br>
* - Uses SPI transactions on Arduino
* - New layout for <a href="Portability.html">easier portability:</a> Break out defines & includes for individual platforms to RF24/utility
* - <a href="MRAA.html">MRAA</a> support added ( Galileo, Edison, etc)
* - <a href="BBB.html">BBB/Generic Linux </a> support via spidev & MRAA
* - Support for RPi 2 added
* - Major Documentation cleanup & update (Move all docs to github.io)
*
* <b>Dec 2014 </b><br>
* - New: Intel Galileo now supported
* - New: Python wrapper for RPi included
* - Documentation updated
* - Example files have been updated
* - See the links below and class documentation for more info.
*
* If issues are discovered with the documentation, please report them <a href="https://github.com/TMRh20/tmrh20.github.io/issues"> here</a>
*
* <br>
* @section Useful Useful References
*
*
* @li <a href="http://tmrh20.github.io/RF24/classRF24.html"><b>RF24</b> Class Documentation</a>
* @li <a href="https://github.com/TMRh20/RF24/archive/master.zip"><b>Download</b></a>
* @li <a href="https://github.com/tmrh20/RF24/"><b>Source Code</b></a>
* @li <a href="http://tmrh20.blogspot.com/2014/03/high-speed-data-transfers-and-wireless.html"><b>My Blog:</b> RF24 Optimization Overview</a>
* @li <a href="http://www.nordicsemi.com/files/Product/data_sheet/nRF24L01_Product_Specification_v2_0.pdf">Chip Datasheet</a>
*
* **Additional Information and Add-ons**
*
* @li <a href="http://tmrh20.github.io/RF24Network"> <b>RF24Network:</b> OSI Network Layer for multi-device communication. Create a home sensor network.</a>
* @li <a href="http://tmrh20.github.io/RF24Mesh"> <b>RF24Mesh:</b> Dynamic Mesh Layer for RF24Network</a>
* @li <a href="http://tmrh20.github.io/RF24Ethernet"> <b>RF24Ethernet:</b> TCP/IP Radio Mesh Networking (shares Arduino Ethernet API)</a>
* @li <a href="http://tmrh20.github.io/RF24Audio"> <b>RF24Audio:</b> Realtime Wireless Audio streaming</a>
* @li <a href="http://tmrh20.github.io/">All TMRh20 Documentation Main Page</a>
*
* **More Information and RF24 Based Projects**
*
* @li <a href="http://TMRh20.blogspot.com"> Project Blog: TMRh20.blogspot.com </a>
* @li <a href="http://maniacalbits.blogspot.ca/"> Maniacal Bits Blog</a>
* @li <a href="http://www.mysensors.org/">MySensors.org (User friendly sensor networks/IoT)</a>
* @li <a href="https://github.com/mannkind/RF24Node_MsgProto"> RF24Node_MsgProto (MQTT)</a>
* @li <a href="https://bitbucket.org/pjhardy/rf24sensornet/"> RF24SensorNet </a>
* @li <a href="http://www.homeautomationforgeeks.com/rf24software.shtml">Home Automation for Geeks</a>
* @li <a href="https://maniacbug.wordpress.com/2012/03/30/rf24network/"> Original Maniacbug RF24Network Blog Post</a>
* @li <a href="https://github.com/maniacbug/RF24"> ManiacBug on GitHub (Original Library Author)</a>
*
*
* <br>
*
* @section Platform_Support Platform Support Pages
*
* @li <a href="Arduino.html"><b>Arduino</b></a> (Uno, Nano, Mega, Due, Galileo, etc)
* @li <a href="ATTiny.html"><b>ATTiny</b></a>
* @li Linux ( <a href="RPi.html"><b>RPi</b></a> , <a href="BBB.html"><b>BBB</b></a>, <a href="MRAA.html"><b>MRAA</b></a> supported boards ( Galileo, Edison, etc))
* @li <a href="Python.html"><b>Python</b></a> wrapper available for RPi
*
* <br>
* **General µC Pin layout** (See the individual board support pages for more info)
*
* The table below shows how to connect the the pins of the NRF24L01(+) to different boards.
* CE and CSN are configurable.
*
* | PIN | NRF24L01 | Arduino UNO | ATtiny25/45/85 [0] | ATtiny44/84 [1] | LittleWire [2] | RPI | RPi -P1 Connector |
* |-----|----------|-------------|--------------------|-----------------|-------------------------|------------|-------------------|
* | 1 | GND | GND | pin 4 | pin 14 | GND | rpi-gnd | (25) |
* | 2 | VCC | 3.3V | pin 8 | pin 1 | regulator 3.3V required | rpi-3v3 | (17) |
* | 3 | CE | digIO 7 | pin 2 | pin 12 | pin to 3.3V | rpi-gpio22 | (15) |
* | 4 | CSN | digIO 8 | pin 3 | pin 11 | RESET | rpi-gpio8 | (24) |
* | 5 | SCK | digIO 13 | pin 7 | pin 9 | SCK | rpi-sckl | (23) |
* | 6 | MOSI | digIO 11 | pin 6 | pin 7 | MOSI | rpi-mosi | (19) |
* | 7 | MISO | digIO 12 | pin 5 | pin 8 | MISO | rpi-miso | (21) |
* | 8 | IRQ | - | - | - | - | - | - |
*
* @li [0] https://learn.sparkfun.com/tutorials/tiny-avr-programmer-hookup-guide/attiny85-use-hints
* @li [1] http://highlowtech.org/?p=1695
* @li [2] http://littlewire.cc/
* <br><br><br>
*
*
*
*
* @page Arduino Arduino
*
* RF24 is fully compatible with Arduino boards <br>
* See <b> http://www.arduino.cc/en/Reference/Board </b> and <b> http://arduino.cc/en/Reference/SPI </b> for more information
*
* RF24 makes use of the standard hardware SPI pins (MISO,MOSI,SCK) and requires two additional pins, to control
* the chip-select and chip-enable functions.<br>
* These pins must be chosen and designated by the user, in RF24 radio(ce_pin,cs_pin); and can use any
* available pins.
*
* <br>
* @section ARD_DUE Arduino Due
*
* RF24 makes use of the extended SPI functionality available on the Arduino Due, and requires one of the
* defined hardware SS/CS pins to be designated in RF24 radio(ce_pin,cs_pin);<br>
* See http://arduino.cc/en/Reference/DueExtendedSPI for more information
*
* Initial Due support taken from https://github.com/mcrosson/RF24/tree/due
*
* <br>
* @section Alternate_SPI Alternate SPI Support
*
* RF24 supports alternate SPI methods, in case the standard hardware SPI pins are otherwise unavailable.
*
* <br>
* **Software Driven SPI**
*
* Software driven SPI is provided by the <a href=https://github.com/greiman/DigitalIO>DigitalIO</a> library
*
* Setup:<br>
* 1. Install the digitalIO library<br>
* 2. Open RF24_config.h in a text editor. Uncomment the line #define SOFTSPI<br>
* 3. In your sketch, add #include DigitalIO.h
*
* @note Note: Pins are listed as follows and can be modified by editing the RF24_config.h file<br>
*
* const uint8_t SOFT_SPI_MISO_PIN = 16;
* const uint8_t SOFT_SPI_MOSI_PIN = 15;
* const uint8_t SOFT_SPI_SCK_PIN = 14;
*
* <br>
* **Alternate Hardware (UART) Driven SPI**
*
* The Serial Port (UART) on Arduino can also function in SPI mode, and can double-buffer data, while the
* default SPI hardware cannot.
*
* The SPI_UART library is available at https://github.com/TMRh20/Sketches/tree/master/SPI_UART
*
* Enabling:
* 1. Install the SPI_UART library
* 2. Edit RF24_config.h and uncomment #define SPI_UART
* 3. In your sketch, add @code #include <SPI_UART.h> @endcode
*
* SPI_UART SPI Pin Connections:
* | NRF |Arduino Uno Pin|
* |-----|---------------|
* | MOSI| TX(0) |
* | MISO| RX(1) |
* | SCK | XCK(4) |
* | CE | User Specified|
* | CSN | User Specified|
*
*
* @note SPI_UART on Mega boards requires soldering to an unused pin on the chip. <br>See
* https://github.com/TMRh20/RF24/issues/24 for more information on SPI_UART.
*
* @page ATTiny ATTiny
*
* ATTiny support is built into the library, so users are not required to include SPI.h in their sketches<br>
* See the included rf24ping85 example for pin info and usage
*
* Some versions of Arduino IDE may require a patch to allow use of the full program space on ATTiny<br>
* See https://github.com/TCWORLD/ATTinyCore/tree/master/PCREL%20Patch%20for%20GCC for ATTiny patch
*
* ATTiny board support initially added from https://github.com/jscrane/RF24
*
* @section Hardware Hardware Configuration
* By tong67 ( https://github.com/tong67 )
*
* **ATtiny25/45/85 Pin map with CE_PIN 3 and CSN_PIN 4**
* @code
* +-\/-+
* NC PB5 1|o |8 Vcc --- nRF24L01 VCC, pin2 --- LED --- 5V
* nRF24L01 CE, pin3 --- PB3 2| |7 PB2 --- nRF24L01 SCK, pin5
* nRF24L01 CSN, pin4 --- PB4 3| |6 PB1 --- nRF24L01 MOSI, pin7
* nRF24L01 GND, pin1 --- GND 4| |5 PB0 --- nRF24L01 MISO, pin6
* +----+
* @endcode
*
* <br>
* **ATtiny25/45/85 Pin map with CE_PIN 3 and CSN_PIN 3** => PB3 and PB4 are free to use for application <br>
* Circuit idea from http://nerdralph.blogspot.ca/2014/01/nrf24l01-control-with-3-attiny85-pins.html <br>
* Original RC combination was 1K/100nF. 22K/10nF combination worked better. <br>
* For best settletime delay value in RF24::csn() the timingSearch3pin.ino sketch can be used. <br>
* This configuration is enabled when CE_PIN and CSN_PIN are equal, e.g. both 3 <br>
* Because CE is always high the power consumption is higher than for 5 pins solution <br>
* @code
* ^^
* +-\/-+ nRF24L01 CE, pin3 ------| //
* PB5 1|o |8 Vcc --- nRF24L01 VCC, pin2 ------x----------x--|<|-- 5V
* NC PB3 2| |7 PB2 --- nRF24L01 SCK, pin5 --|<|---x-[22k]--| LED
* NC PB4 3| |6 PB1 --- nRF24L01 MOSI, pin6 1n4148 |
* nRF24L01 GND, pin1 -x- GND 4| |5 PB0 --- nRF24L01 MISO, pin7 |
* | +----+ |
* |-----------------------------------------------||----x-- nRF24L01 CSN, pin4
* 10nF
* @endcode
*
* <br>
* **ATtiny24/44/84 Pin map with CE_PIN 8 and CSN_PIN 7** <br>
* Schematic provided and successfully tested by Carmine Pastore (https://github.com/Carminepz) <br>
* @code
* +-\/-+
* nRF24L01 VCC, pin2 --- VCC 1|o |14 GND --- nRF24L01 GND, pin1
* PB0 2| |13 AREF
* PB1 3| |12 PA1
* PB3 4| |11 PA2 --- nRF24L01 CE, pin3
* PB2 5| |10 PA3 --- nRF24L01 CSN, pin4
* PA7 6| |9 PA4 --- nRF24L01 SCK, pin5
* nRF24L01 MOSI, pin7 --- PA6 7| |8 PA5 --- nRF24L01 MISO, pin6
* +----+
* @endcode
*
* <br><br><br>
*
*
*
*
*
*
* @page BBB BeagleBone Black
*
* BeagleBone Black is supported via MRAA or SPIDEV.
*
* @note The SPIDEV option should work with most Linux systems supporting SPIDEV. <br>
* Users may need to edit the RF24/utility/BBB/spi.cpp file to configure the spi device. (Defaults: "/dev/spidev1.0"; or "/dev/spidev1.1"; )
*
* <br>
* @section AutoInstall Automated Install
*(**Designed & Tested on RPi** - Defaults to SPIDEV on BBB)
*
*
* 1. Download the install.sh file from http://tmrh20.github.io/RF24Installer/RPi/install.sh
* @code wget http://tmrh20.github.io/RF24Installer/RPi/install.sh @endcode
* 2. Make it executable:
* @code chmod +x install.sh @endcode
* 3. Run it and choose your options
* @code ./install.sh @endcode
* 4. Run an example from one of the libraries
* @code
* cd rf24libs/RF24/examples_RPi
* @endcode
* Edit the gettingstarted example, to set your pin configuration
* @code nano gettingstarted.cpp
* make
* sudo ./gettingstarted
* @endcode
*
* <br>
* @section ManInstall Manual Install
* 1. Make a directory to contain the RF24 and possibly RF24Network lib and enter it:
* @code
* mkdir ~/rf24libs
* cd ~/rf24libs
* @endcode
* 2. Clone the RF24 repo:
* @code git clone https://github.com/tmrh20/RF24.git RF24 @endcode
* 3. Change to the new RF24 directory
* @code cd RF24 @endcode
* 4. Build the library, and run an example file:
* **Note:** See the <a href="http://iotdk.intel.com/docs/master/mraa/index.html">MRAA </a> documentation for more info on installing MRAA
* @code sudo make install OR sudo make install RF24_MRAA=1 @endcode
* @code
* cd examples_RPi
* @endcode
* Edit the gettingstarted example, to set your pin configuration
* @code nano gettingstarted.cpp
* make
* sudo ./gettingstarted
* @endcode
*
* <br><br>
*
* @page MRAA MRAA
*
* MRAA is a Low Level Skeleton Library for Communication on GNU/Linux platforms <br>
* See http://iotdk.intel.com/docs/master/mraa/index.html for more information
*
* RF24 supports all MRAA supported platforms, but might not be tested on each individual platform due to the wide range of hardware support:<br>
* <a href="https://github.com/TMRh20/RF24/issues">Report an RF24 bug or issue </a>
*
* @section Setup Setup
* 1. Install the MRAA lib
* 2. As per your device, SPI may need to be enabled
*
* @section MRAA_Install Install
*
* 1. Make a directory to contain the RF24 and possibly RF24Network lib and enter it:
* @code
* mkdir ~/rf24libs
* cd ~/rf24libs
* @endcode
* 2. Clone the RF24 repo:
* @code git clone https://github.com/tmrh20/RF24.git RF24 @endcode
* 3. Change to the new RF24 directory
* @code cd RF24 @endcode
* 4. Build the library:
* @code sudo make install -B RF24_MRAA=1 @endcode
* 5. Configure the correct pins in gettingstarted.cpp (See http://iotdk.intel.com/docs/master/mraa/index.html )
* @code
* cd examples_RPi
* nano gettingstarted.cpp
* @endcode
* 6. Build an example
* @code
* make
* sudo ./gettingstarted
* @endcode
*
* <br><br><br>
*
*
*
*
* @page RPi Raspberry Pi
*
* RF24 supports a variety of Linux based devices via various drivers. Some boards like RPi can utilize multiple methods
* to drive the GPIO and SPI functionality.
*
* <br>
* @section PreConfig Potential PreConfiguration
*
* If SPI is not already enabled, load it on boot:
* @code sudo raspi-config @endcode
* A. Update the tool via the menu as required<br>
* B. Select **Advanced** and **enable the SPI kernel module** <br>
* C. Update other software and libraries:
* @code sudo apt-get update @endcode
* @code sudo apt-get upgrade @endcode
* <br>
* @section AutoInstall Automated Install
*
* 1. Download the install.sh file from http://tmrh20.github.io/RF24Installer/RPi/install.sh
* @code wget http://tmrh20.github.io/RF24Installer/RPi/install.sh @endcode
* 2. Make it executable:
* @code chmod +x install.sh @endcode
* 3. Run it and choose your options
* @code ./install.sh @endcode
* 4. Run an example from one of the libraries
* @code
* cd rf24libs/RF24/examples_RPi
* make
* sudo ./gettingstarted
* @endcode
* <br><br>
* @section ManInstall Manual Install
* 1. Make a directory to contain the RF24 and possibly RF24Network lib and enter it:
* @code
* mkdir ~/rf24libs
* cd ~/rf24libs
* @endcode
* 2. Clone the RF24 repo:
* @code git clone https://github.com/tmrh20/RF24.git RF24 @endcode
* 3. Change to the new RF24 directory
* @code cd RF24 @endcode
* 4. Build the library, and run an example file:
* @code sudo make install
* cd examples_RPi
* make
* sudo ./gettingstarted
* @endcode
*
* <br><br>
* @section Build Build Options
* The default build on Raspberry Pi utilizes the included **BCM2835** driver from http://www.airspayce.com/mikem/bcm2835
* 1. @code sudo make install -B @endcode
*
* Build using the **MRAA** library from http://iotdk.intel.com/docs/master/mraa/index.html <br>
* MRAA is not included. See the <a href="MRAA.html">MRAA</a> platform page for more information.
*
* 1. Install, and build MRAA:
* @code
* git clone https://github.com/intel-iot-devkit/mraa.git
* cd mraa
* mkdir build
* cd build
* cmake .. -DBUILDSWIGNODE=OFF
* sudo make install
* @endcode
*
* 2. Complete the install <br>
* @code nano /etc/ld.so.conf @endcode
* Add the line @code /usr/local/lib/arm-linux-gnueabihf @endcode
* Run @code sudo ldconfig @endcode
*
* 3. Install RF24, using MRAA
* @code sudo make install -B RF24_MRAA=1 @endcode
* See the gettingstarted example for an example of pin configuration
*
* Build using **spidev**:
*
* 1. Edit the RF24/utility/BBB/spi.cpp file
* 2. Change the default device definition to @code this->device = "/dev/spidev0.0";; @endcode
* 3. Run @code sudo make install -B RF24_SPIDEV=1 @endcode
* 4. See the gettingstarted example for an example of pin configuration
*
* <br>
* @section Pins Connections and Pin Configuration
*
*
* Using pin 15/GPIO 22 for CE, pin 24/GPIO8 (CE0) for CSN
*
* Can use either RPi CE0 or CE1 pins for radio CSN.<br>
* Choose any RPi output pin for radio CE pin.
*
* **BCM2835 Constructor:**
* @code
* RF24 radio(RPI_V2_GPIO_P1_15,BCM2835_SPI_CS0, BCM2835_SPI_SPEED_8MHZ);
* or
* RF24 radio(RPI_V2_GPIO_P1_15,BCM2835_SPI_CS1, BCM2835_SPI_SPEED_8MHZ);
*
* RPi B+:
* RF24 radio(RPI_BPLUS_GPIO_J8_15,RPI_BPLUS_GPIO_J8_24, BCM2835_SPI_SPEED_8MHZ);
* or
* RF24 radio(RPI_BPLUS_GPIO_J8_15,RPI_BPLUS_GPIO_J8_26, BCM2835_SPI_SPEED_8MHZ);
*
* General:
* RF24 radio(22,0);
* or
* RF24 radio(22,1);
*
* @endcode
* See the gettingstarted example for an example of pin configuration
*
* See http://www.airspayce.com/mikem/bcm2835/index.html for BCM2835 class documentation.
* <br><br>
* **MRAA Constructor:**
*
* @code RF24 radio(15,0); @endcode
*
* See http://iotdk.intel.com/docs/master/mraa/rasppi.html
* <br><br>
* **SPI_DEV Constructor**
*
* @code RF24 radio(22,0); @endcode
*
* See http://pi.gadgetoid.com/pinout
*
* **Pins:**
*
* | PIN | NRF24L01 | RPI | RPi -P1 Connector |
* |-----|----------|------------|-------------------|
* | 1 | GND | rpi-gnd | (25) |
* | 2 | VCC | rpi-3v3 | (17) |
* | 3 | CE | rpi-gpio22 | (15) |
* | 4 | CSN | rpi-gpio8 | (24) |
* | 5 | SCK | rpi-sckl | (23) |
* | 6 | MOSI | rpi-mosi | (19) |
* | 7 | MISO | rpi-miso | (21) |
* | 8 | IRQ | - | - |
*
*
*
*
* <br><br>
****************
*
* Based on the arduino lib from J. Coliz <maniacbug@ymail.com> <br>
* the library was berryfied by Purinda Gunasekara <purinda@gmail.com> <br>
* then forked from github stanleyseow/RF24 to https://github.com/jscrane/RF24-rpi <br>
* Network lib also based on https://github.com/farconada/RF24Network
*
*
*
*
* <br><br><br>
*
*
*
* @page Python Python Wrapper (by https://github.com/mz-fuzzy)
*
* @section Install Installation:
*
* Install the boost libraries: (Note: Only the python libraries should be needed, this is just for simplicity)
*
* @code sudo apt-get install libboost1.50-all @endcode
*
* Build the library:
*
* @code ./setup.py build @endcode
*
* Install the library
*
* @code sudo ./setup.py install @endcode
*
*
* See the additional <a href="pages.html">Platform Support</a> pages for information on connecting your hardware <br>
* See the included <a href="pingpair_dyn_8py-example.html">example </a> for usage information.
*
* Running the Example:
*
* Edit the pingpair_dyn.py example to configure the appropriate pins per the above documentation:
*
* @code nano pingpair_dyn.py @endcode
*
* Configure another device, Arduino or RPi with the <a href="pingpair_dyn_8py-example.html">pingpair_dyn</a> example
*
* Run the example
*
* @code sudo ./pingpair_dyn.py @endcode
*
* <br><br><br>
*
*
* @page Portability RF24 Portability
*
* The RF24 radio driver mainly utilizes the <a href="http://arduino.cc/en/reference/homePage">Arduino API</a> for GPIO, SPI, and timing functions, which are easily replicated
* on various platforms. <br>Support files for these platforms are stored under RF24/utility, and can be modified to provide
* the required functionality.
*
* <br>
* @section Hardware_Templates Basic Hardware Template
*
* **RF24/utility**
*
* The RF24 library now includes a basic hardware template to assist in porting to various platforms. <br> The following files can be included
* to replicate standard Arduino functions as needed, allowing devices from ATTiny to Raspberry Pi to utilize the same core RF24 driver.
*
* | File | Purpose |
* |--------------------|------------------------------------------------------------------------------|
* | RF24_arch_config.h | Basic Arduino/AVR compatibility, includes for remaining support files, etc |
* | includes.h | Linux only. Defines specific platform, include correct RF24_arch_config file |
* | spi.h | Provides standardized SPI ( transfer() ) methods |
* | gpio.h | Provides standardized GPIO ( digitalWrite() ) methods |
* | compatibility.h | Provides standardized timing (millis(), delay()) methods |
* | your_custom_file.h | Provides access to custom drivers for spi,gpio, etc |
*
* <br>
* Examples are provided via the included hardware support templates in **RF24/utility** <br>
* See the <a href="modules.html">modules</a> page for examples of class declarations
*
*<br>
* @section Device_Detection Device Detection
*
* 1. The main detection for Linux devices is done in the Makefile, with the includes.h from the proper hardware directory copied to RF24/utility/includes.h <br>
* 2. Secondary detection is completed in RF24_config.h, causing the include.h file to be included for all supported Linux devices <br>
* 3. RF24.h contains the declaration for SPI and GPIO objects 'spi' and 'gpio' to be used for porting-in related functions.
*
* <br>
* @section Ported_Code Code
* To have your ported code included in this library, or for assistance in porting, create a pull request or open an issue at https://github.com/TMRh20/RF24
*
*
*<br><br><br>
*/
#endif // __RF24_H__