Diff: targets/TARGET_Silicon_Labs/inc/usbconfig.h

Revision:

71:53949e6131f6

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/TARGET_Silicon_Labs/inc/usbconfig.h	Thu Jul 27 12:14:04 2017 +0100
@@ -0,0 +1,88 @@
+/***************************************************************************//**
+ * @file usbconfig.h
+ * @brief USB protocol stack library, application supplied configuration options.
+ * @version 3.20.12
+ *******************************************************************************
+ * @section License
+ * <b>(C) Copyright 2014 Silicon Labs, http://www.silabs.com</b>
+ *******************************************************************************
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ *
+ ******************************************************************************/
+
+#ifndef __USBCONFIG_H
+#define __USBCONFIG_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Compile stack for device mode. */
+#define USB_DEVICE
+
+/* Maximum number of endpoint used, EP0 excluded. If you change this, you must
+   also change USBEndpoints_EFM32.h to match. */
+#define NUM_EP_USED 6
+
+/* Power management modes. The following can be or'd toghether. See comments in
+   em_usbd.c under "Energy-saving modes" for more details.
+
+   USB_PWRSAVE_MODE_ONSUSPEND  Set USB peripheral in low power mode on suspend
+
+   USB_PWRSAVE_MODE_ONVBUSOFF  Set USB peripheral in low power mode when not
+   attached to a host. While this mode assumes that the internal voltage regulator
+   is used and that the VREGI pin of the chip is connected to VBUS it should
+   be safe to use given that VREGOSEN is always enabled. If you disable VREGOSEN
+   you must turn this off.
+
+   USB_PWRSAVE_MODE_ENTEREM2  Enter EM2 when USB peripheral is in low power mode.
+   On Mbed this allows the sleep() and deepsleep() calls to enter EM2, but
+   does not automatically enter any sleep states. Entering EM1 is always allowed.
+
+   Note for Happy Gecko, errata USB_E111: Entering EM2 when both the system clock
+   (HFCLK) and the USB core clock (USBCCLK) is running on USHFRCO will result in
+   a lock-up.
+*/
+#define USB_PWRSAVE_MODE  (USB_PWRSAVE_MODE_ONSUSPEND|USB_PWRSAVE_MODE_ONVBUSOFF|USB_PWRSAVE_MODE_ENTEREM2)
+
+/* Use dynamic memory to allocate rx/tx buffers in the HAL. Saves memory
+   as buffers are only allocated for used endpoints. The system malloc
+   must return memory that is aligned by 4.
+
+   Note: if you disable this, using isochronous endpoints with packet
+   sizes that are larger than the maximum for other EP types (64) will
+   not work. */
+#define USB_USE_DYNAMIC_MEMORY
+
+/* When the USB peripheral is set in low power mode, it must be clocked by a 32kHz
+   clock. Both LFXO and LFRCO can be used, but only LFXO guarantee USB specification
+   compliance. */
+#define USB_USBC_32kHz_CLK   USB_USBC_32kHz_CLK_LFXO
+
+/* Uncomment to get some debugging information. Default value for USER_PUTCHAR
+   should work for SiLabs Gecko boards. Printf requires a working retarget
+   implementation for write(). */
+//#define DEBUG_USB_API
+//#define USB_USE_PRINTF
+//#define USER_PUTCHAR   ITM_SendChar
+//#define DEBUG_USB_INT_HI
+//#define DEBUG_USB_INT_LO
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __USBCONFIG_H */