Digi International Inc.
ZigBee Send Data example for mbed XBeeLib By Digi
Description
This example shows how to send data to a remote XBeeZB module.
The application creates a message for a remote XBee module.
This library encodes and sends it to the local XBee module through the serial port. Then the local XBee module sends the packet to the remote XBee module through the air.
The example shows how to send both unicast and broadcast messages. It also shows how to send messages to the network coordinator.
See Sending data to another module chapter for more information.
Common Setup
Make sure you have a valid Example Common Setup
Example Setup
Application
Broadcast messages and messages to the coordinator don't require any configuration, but for unicast messages to a specific node you have to configure the remote device 64-bit address by customizing the REMOTE_NODE_ADDR64_MSB and REMOTE_NODE_ADDR64_LSB defines with the remote XBee module 64-bit address.
Running the example
Build and deploy the example to the mbed module.
Reset the mbed module so the example starts. You should see the example debug information through the debug interface configured in the 'Local Setup' chapter.
Once joined to the coordinator, the application will first send a message to the coordinator, then a broadcast message and finally a couple of unicast messages to the configured remote XBee module.
Verify that the remote XBee module is receiving the frames by accessing the "Console" tab of the X-CTU. You should see there the broadcast and unicast messages. If the remote XBee module is also the network coordinator, you should see there also the message sent to the coordinator.
config.h
- Committer:
- hbujanda
- Date:
- 2016-07-29
- Revision:
- 10:b75412a32a4c
- Parent:
- 7:d685568a3bc8
File content as of revision 10:b75412a32a4c:
/**
* Copyright (c) 2015 Digi International Inc.,
* All rights not expressly granted are reserved.
*
* This Source Code Form is subject to the terms of the Mozilla Public
* License, v. 2.0. If a copy of the MPL was not distributed with this file,
* You can obtain one at http://mozilla.org/MPL/2.0/.
*
* Digi International Inc. 11001 Bren Road East, Minnetonka, MN 55343
* =======================================================================
*/
#ifndef __CONFIG_H_
#define __CONFIG_H_
/** Library configuration options */
#define ENABLE_LOGGING
#define ENABLE_ASSERTIONS
#define FRAME_BUFFER_SIZE 4
#define MAX_FRAME_PAYLOAD_LEN 128
#define SYNC_OPS_TIMEOUT_MS 2000
//#define RADIO_TX NC /* TODO: specify your setup's Serial TX pin connected to the XBee module DIN pin */
//#define RADIO_RX NC /* TODO: specify your setup's Serial RX pin connected to the XBee module DOUT pin */
//#define RADIO_RTS NC /* TODO: specify your setup's Serial RTS# pin connected to the XBee module RTS# pin */
//#define RADIO_CTS NC /* TODO: specify your setup's Serial CTS# pin connected to the XBee module CTS# pin */
//#define RADIO_RESET NC /* TODO: specify your setup's GPIO (output) connected to the XBee module's reset pin */
//#define RADIO_SLEEP_REQ NC /* TODO: specify your setup's GPIO (output) connected to the XBee module's SLEEP_RQ pin */
//#define RADIO_ON_SLEEP NC /* TODO: specify your setup's GPIO (input) connected to the XBee module's ON_SLEEP pin */
//#define DEBUG_TX NC /* TODO: specify your setup's Serial TX for debugging */
//#define DEBUG_RX NC /* TODO: specify your setup's Serial RX for debugging (optional) */
#if !defined(RADIO_TX)
#error "Please define RADIO_TX pin"
#endif
#if !defined(RADIO_RX)
#error "Please define RADIO_RX pin"
#endif
#if !defined(RADIO_RESET)
#define RADIO_RESET NC
#warning "RADIO_RESET not defined, defaulted to 'NC'"
#endif
#if defined(ENABLE_LOGGING)
#if !defined(DEBUG_TX)
#error "Please define DEBUG_TX"
#endif
#if !defined(DEBUG_RX)
#define DEBUG_RX NC
#warning "DEBUG_RX not defined, defaulted to 'NC'"
#endif
#endif
#endif /* __CONFIG_H_ */