Digi International Inc. / Mbed 2 deprecated XBeeDM_dio_adc_pwm

DigiMEsh DIOs, ADCs and PWMs example for mbed XBeeLib By Digi

Dependencies:   XBeeLib mbed

Fork of XBeeZB_dio_adc by Digi International Inc.

This example shows how to handle remote XBee modules DigitalInputOutputs, ADCs and PWMs. The example configures the remote XBee module pins to the desired functionality and then operates on those pins.

See Handling remote modules DIOs ADCs and PWMs chapter for more information.

Common Setup

Make sure you have a valid Example Common Setup

Example Setup

Application

You have to configure the remote device 64-bit address by customizing the REMOTE_NODE_ADDR64_MSB and REMOTE_NODE_ADDR64_LSB defines with the remote XBee module 64-bit address.

Hardware

On the Remote XBee module, wire following peripherals to the pins specified on the table and schematics or change the application pins according to your hardware setup:

LinePinValue
DIO2/ADC218ADC (Analog Input)
DIO3/ADC317Digital Input
RSSI/DIO106PWM (Analog Output)
DIO411Digital Output

/media/uploads/hbujanda/dio_adc_schem.png

Running the example

Build and deploy the example to the mbed module.
Reset the mbed module so the example starts. You should see the example debug information through the debug interface configured in the 'Local Setup' chapter.
The application will do following operations:

  • Configure the remote XBee module pins according to the table above.
  • Do following loop every 5 seconds:
    • Read DIO3_AD3 digital value
    • Toggle LED associated to DIO4_AD4
    • Read DIO2_AD2 analog value
    • Set the led associated to PWM0 to different intensity levels

config.h

Committer:
spastor
Date:
2015-05-05
Revision:
1:adeb9c8818ab
Parent:
0:c87d86778f27
Child:
3:dd41eadd74a3

File content as of revision 1:adeb9c8818ab:


#if !defined(__CONFIG_H_)
#define __CONFIG_H_

//#define PATFORM_ARCHPRO

/** Library configuration options */
#define ENABLE_LOGGING
#define ENABLE_ASSERTIONS
#define FRAME_BUFFER_SIZE   4
#define MAX_FRAME_PAYLOAD_LEN  128
#define ENABLE_PM_SUPPORT

#define SYNC_OPS_TIMEOUT_MS       2000

#if defined(PATFORM_ARCHPRO)
#define RADIO_TX            P4_28
#define RADIO_RX            P4_29
#define RADIO_RESET         NC
//#define RADIO_RESET         NC
#define RADIO_SLEEP_REQ     NC
#define RADIO_ON_SLEEP      NC
#define DEBUG_TX            P0_2
#define DEBUG_RX            P0_3
#elif defined(TARGET_LPC1768)
#define RADIO_TX            p9
#define RADIO_RX            p10
#define RADIO_RESET         p30
#define RADIO_SLEEP_REQ     NC
#define RADIO_ON_SLEEP      NC
#define DEBUG_TX            P0_2
#define DEBUG_RX            P0_3
#elif defined(TARGET_FRDM_KL25)
#define RADIO_TX            PTD3
#define RADIO_RX            PTD2
#define RADIO_RESET         NC
#define RADIO_SLEEP_REQ     NC
#define RADIO_ON_SLEEP      NC
#define DEBUG_TX            USBTX
#define DEBUG_RX            USBRX
#elif (defined TARGET_LPC11U24)
#define RADIO_TX            p9
#define RADIO_RX            p10
#define RADIO_RESET         p30
#define RADIO_SLEEP_REQ     NC
#define RADIO_ON_SLEEP      NC
#define DEBUG_TX            USBTX
#define DEBUG_RX            USBRX
#else
#error "Define a platform"
#endif

#endif /* __CONFIG_H_ */