20160814
Fork of RF24 by
Revision 8:6827b6f0283b, committed 2016-07-28
- Comitter:
- adam_z
- Date:
- Thu Jul 28 08:10:31 2016 +0000
- Parent:
- 7:32d6957f37ae
- Commit message:
- RF24 lib modified from https://developer.mbed.org/users/akashvibhute/code/RF24/docs/tip/RF24_8cpp_source.html
Changed in this revision
RF24.cpp | Show annotated file Show diff for this revision Revisions of this file |
--- a/RF24.cpp Thu Jun 16 08:56:06 2016 +0000 +++ b/RF24.cpp Thu Jul 28 08:10:31 2016 +0000 @@ -26,42 +26,7 @@ csn_pin = mode; - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - + } /****************************************************************************/ @@ -96,25 +61,6 @@ uint8_t status; - - - - - - - - - - - - - - - - - - - beginTransaction(); status = spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); @@ -134,20 +80,6 @@ { uint8_t result; - - - - - - - - - - - - - - beginTransaction(); spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); @@ -164,21 +96,7 @@ uint8_t RF24::write_register(uint8_t reg, const uint8_t* buf, uint8_t len) { uint8_t status; - - - - - - - - - - - - - - - + beginTransaction(); status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); @@ -200,17 +118,6 @@ IF_SERIAL_DEBUG(printf_P(PSTR("write_register(%02x,%02x)\r\n"),reg,value)); - - - - - - - - - - - beginTransaction(); status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); spi.write(value); @@ -235,24 +142,6 @@ IF_SERIAL_DEBUG( printf("[Writing %u bytes %u blanks]\n",data_len,blank_len); ); - - - - - - - - - - - - - - - - - - beginTransaction(); status = spi.write( writeType ); while ( data_len-- ) { @@ -283,30 +172,6 @@ IF_SERIAL_DEBUG( printf("[Reading %u bytes %u blanks]\n",data_len,blank_len); ); - - - - - - - - - - - - - - - - - - - - - - - - beginTransaction(); status = spi.write( R_RX_PAYLOAD ); @@ -430,7 +295,7 @@ pipe0_reading_address[0]=0; //spi.frequency(10000000/5); // 2Mbit, 1/5th the maximum transfer rate for the spi bus - spi.frequency(10000000); + spi.frequency(10000000/5); //spi.format(8,0); // 8-bit, ClockPhase = 0, ClockPolarity = 0 spi.format(8,0); wait_ms(10); @@ -524,37 +389,6 @@ { - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - print_status(get_status()); print_address_register(PSTR("RX_ADDR_P0-1"),RX_ADDR_P0,2); @@ -594,42 +428,6 @@ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - // Must allow the radio time to settle else configuration bits will not necessarily stick. // This is actually only required following power up but some settling time also appears to // be required after resets too. For full coverage, we'll always assume the worst. @@ -664,10 +462,10 @@ // Then set the data rate to the slowest (and most reliable) speed supported by all // hardware. //setDataRate( RF24_1MBPS ) ; - setDataRate( RF24_2MBPS ) ; + setDataRate( RF24_1MBPS ) ; // Initialize CRC and request 2-byte (16bit) CRC - //setCRCLength( RF24_CRC_16 ) ; + setCRCLength( RF24_CRC_16 ) ; // Disable dynamic payloads, to match dynamic_payloads_enabled setting - Reset value is 0 toggle_features(); @@ -744,12 +542,6 @@ write_register(NRF_CONFIG, ( read_register(NRF_CONFIG) ) & ~_BV(PRIM_RX) ); - - - - - - write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[0]))); // Enable RX on pipe0 //delayMicroseconds(100); @@ -1044,13 +836,6 @@ uint8_t result = 0; - - - - - - - beginTransaction(); spi.write( R_RX_PL_WID ); result = spi.write(0xff); @@ -1300,17 +1085,7 @@ uint8_t data_len = rf24_min(len,32); - - - - - - - - - - - + beginTransaction(); spi.write(W_ACK_PAYLOAD | ( pipe & 0b111 ) );