Mouse code for the MacroRat
Diff: mbed-dev/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_hal_rtc.c
- Revision:
- 18:6a4db94011d3
diff -r f713758f6238 -r 6a4db94011d3 mbed-dev/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_hal_rtc.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_hal_rtc.c Sun May 14 23:18:57 2017 +0000 @@ -0,0 +1,1547 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_rtc.c + * @author MCD Application Team + * @version V1.5.0 + * @date 06-May-2016 + * @brief RTC HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Real Time Clock (RTC) peripheral: + * + Initialization and de-initialization functions + * + RTC Time and Date functions + * + RTC Alarm functions + * + Peripheral Control functions + * + Peripheral State functions + * + @verbatim + ============================================================================== + ##### Backup Domain Operating Condition ##### + ============================================================================== + [..] The real-time clock (RTC), the RTC backup registers, and the backup + SRAM (BKP SRAM) can be powered from the VBAT voltage when the main + VDD supply is powered off. + To retain the content of the RTC backup registers, backup SRAM, and supply + the RTC when VDD is turned off, VBAT pin can be connected to an optional + standby voltage supplied by a battery or by another source. + + [..] To allow the RTC operating even when the main digital supply (VDD) is turned + off, the VBAT pin powers the following blocks: + (#) The RTC + (#) The LSE oscillator + (#) The backup SRAM when the low power backup regulator is enabled + (#) PC13 to PC15 I/Os, plus PI8 I/O (when available) + + [..] When the backup domain is supplied by VDD (analog switch connected to VDD), + the following pins are available: + (#) PC14 and PC15 can be used as either GPIO or LSE pins + (#) PC13 can be used as a GPIO or as the RTC_AF1 pin + (#) PI8 can be used as a GPIO or as the RTC_AF2 pin + + [..] When the backup domain is supplied by VBAT (analog switch connected to VBAT + because VDD is not present), the following pins are available: + (#) PC14 and PC15 can be used as LSE pins only + (#) PC13 can be used as the RTC_AF1 pin + (#) PI8 can be used as the RTC_AF2 pin + + ##### Backup Domain Reset ##### + ================================================================== + [..] The backup domain reset sets all RTC registers and the RCC_BDCR register + to their reset values. The BKPSRAM is not affected by this reset. The only + way to reset the BKPSRAM is through the Flash interface by requesting + a protection level change from 1 to 0. + [..] A backup domain reset is generated when one of the following events occurs: + (#) Software reset, triggered by setting the BDRST bit in the + RCC Backup domain control register (RCC_BDCR). + (#) VDD or VBAT power on, if both supplies have previously been powered off. + + ##### Backup Domain Access ##### + ================================================================== + [..] After reset, the backup domain (RTC registers, RTC backup data + registers and backup SRAM) is protected against possible unwanted write + accesses. + [..] To enable access to the RTC Domain and RTC registers, proceed as follows: + (+) Enable the Power Controller (PWR) APB1 interface clock using the + __HAL_RCC_PWR_CLK_ENABLE() function. + (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function. + (+) Select the RTC clock source using the __HAL_RCC_RTC_CONFIG() function. + (+) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() function. + + + ##### How to use this driver ##### + ================================================================== + [..] + (+) Enable the RTC domain access (see description in the section above). + (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour + format using the HAL_RTC_Init() function. + + *** Time and Date configuration *** + =================================== + [..] + (+) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime() + and HAL_RTC_SetDate() functions. + (+) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions. + + *** Alarm configuration *** + =========================== + [..] + (+) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function. + You can also configure the RTC Alarm with interrupt mode using the HAL_RTC_SetAlarm_IT() function. + (+) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function. + + ##### RTC and low power modes ##### + ================================================================== + [..] The MCU can be woken up from a low power mode by an RTC alternate + function. + [..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B), + RTC wake-up, RTC tamper event detection and RTC time stamp event detection. + These RTC alternate functions can wake up the system from the Stop and + Standby low power modes. + [..] The system can also wake up from low power modes without depending + on an external interrupt (Auto-wake-up mode), by using the RTC alarm + or the RTC wake-up events. + [..] The RTC provides a programmable time base for waking up from the + Stop or Standby mode at regular intervals. + Wake-up from STOP and STANDBY modes is possible only when the RTC clock source + is LSE or LSI. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @defgroup RTC RTC + * @brief RTC HAL module driver + * @{ + */ + +#ifdef HAL_RTC_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup RTC_Exported_Functions RTC Exported Functions + * @{ + */ + +/** @defgroup RTC_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] This section provides functions allowing to initialize and configure the + RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable + RTC registers Write protection, enter and exit the RTC initialization mode, + RTC registers synchronization check and reference clock detection enable. + (#) The RTC Prescaler is programmed to generate the RTC 1Hz time base. + It is split into 2 programmable prescalers to minimize power consumption. + (++) A 7-bit asynchronous prescaler and a 13-bit synchronous prescaler. + (++) When both prescalers are used, it is recommended to configure the + asynchronous prescaler to a high value to minimize power consumption. + (#) All RTC registers are Write protected. Writing to the RTC registers + is enabled by writing a key into the Write Protection register, RTC_WPR. + (#) To configure the RTC Calendar, user application should enter + initialization mode. In this mode, the calendar counter is stopped + and its value can be updated. When the initialization sequence is + complete, the calendar restarts counting after 4 RTCCLK cycles. + (#) To read the calendar through the shadow registers after Calendar + initialization, calendar update or after wake-up from low power modes + the software must first clear the RSF flag. The software must then + wait until it is set again before reading the calendar, which means + that the calendar registers have been correctly copied into the + RTC_TR and RTC_DR shadow registers.The HAL_RTC_WaitForSynchro() function + implements the above software sequence (RSF clear and RSF check). + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the RTC peripheral + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc) +{ + /* Check the RTC peripheral state */ + if(hrtc == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_RTC_HOUR_FORMAT(hrtc->Init.HourFormat)); + assert_param(IS_RTC_ASYNCH_PREDIV(hrtc->Init.AsynchPrediv)); + assert_param(IS_RTC_SYNCH_PREDIV(hrtc->Init.SynchPrediv)); + assert_param (IS_RTC_OUTPUT(hrtc->Init.OutPut)); + assert_param (IS_RTC_OUTPUT_POL(hrtc->Init.OutPutPolarity)); + assert_param(IS_RTC_OUTPUT_TYPE(hrtc->Init.OutPutType)); + + if(hrtc->State == HAL_RTC_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + hrtc->Lock = HAL_UNLOCKED; + /* Initialize RTC MSP */ + HAL_RTC_MspInit(hrtc); + } + + /* Set RTC state */ + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Set Initialization mode */ + if(RTC_EnterInitMode(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Set RTC state */ + hrtc->State = HAL_RTC_STATE_ERROR; + + return HAL_ERROR; + } + else + { + /* Clear RTC_CR FMT, OSEL and POL Bits */ + hrtc->Instance->CR &= ((uint32_t)~(RTC_CR_FMT | RTC_CR_OSEL | RTC_CR_POL)); + /* Set RTC_CR register */ + hrtc->Instance->CR |= (uint32_t)(hrtc->Init.HourFormat | hrtc->Init.OutPut | hrtc->Init.OutPutPolarity); + + /* Configure the RTC PRER */ + hrtc->Instance->PRER = (uint32_t)(hrtc->Init.SynchPrediv); + hrtc->Instance->PRER |= (uint32_t)(hrtc->Init.AsynchPrediv << 16U); + + /* Exit Initialization mode */ + hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; + + hrtc->Instance->TAFCR &= (uint32_t)~RTC_TAFCR_ALARMOUTTYPE; + hrtc->Instance->TAFCR |= (uint32_t)(hrtc->Init.OutPutType); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Set RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; + } +} + +/** + * @brief DeInitializes the RTC peripheral + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @note This function doesn't reset the RTC Backup Data registers. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc) +{ + uint32_t tickstart = 0U; + + /* Set RTC state */ + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Set Initialization mode */ + if(RTC_EnterInitMode(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Set RTC state */ + hrtc->State = HAL_RTC_STATE_ERROR; + + return HAL_ERROR; + } + else + { + /* Reset TR, DR and CR registers */ + hrtc->Instance->TR = (uint32_t)0x00000000U; + hrtc->Instance->DR = (uint32_t)0x00002101U; + /* Reset All CR bits except CR[2:0] */ + hrtc->Instance->CR &= (uint32_t)0x00000007U; + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait till WUTWF flag is set and if Time out is reached exit */ + while(((hrtc->Instance->ISR) & RTC_ISR_WUTWF) == (uint32_t)RESET) + { + if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Set RTC state */ + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + return HAL_TIMEOUT; + } + } + + /* Reset all RTC CR register bits */ + hrtc->Instance->CR &= (uint32_t)0x00000000U; + hrtc->Instance->WUTR = (uint32_t)0x0000FFFFU; + hrtc->Instance->PRER = (uint32_t)0x007F00FFU; + hrtc->Instance->CALIBR = (uint32_t)0x00000000U; + hrtc->Instance->ALRMAR = (uint32_t)0x00000000U; + hrtc->Instance->ALRMBR = (uint32_t)0x00000000U; + hrtc->Instance->SHIFTR = (uint32_t)0x00000000U; + hrtc->Instance->CALR = (uint32_t)0x00000000U; + hrtc->Instance->ALRMASSR = (uint32_t)0x00000000U; + hrtc->Instance->ALRMBSSR = (uint32_t)0x00000000U; + + /* Reset ISR register and exit initialization mode */ + hrtc->Instance->ISR = (uint32_t)0x00000000U; + + /* Reset Tamper and alternate functions configuration register */ + hrtc->Instance->TAFCR = 0x00000000U; + + /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ + if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) + { + if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_ERROR; + + return HAL_ERROR; + } + } + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* De-Initialize RTC MSP */ + HAL_RTC_MspDeInit(hrtc); + + hrtc->State = HAL_RTC_STATE_RESET; + + /* Release Lock */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Initializes the RTC MSP. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval None + */ +__weak void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RTC_MspInit could be implemented in the user file + */ +} + +/** + * @brief DeInitializes the RTC MSP. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval None + */ +__weak void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RTC_MspDeInit could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup RTC_Exported_Functions_Group2 RTC Time and Date functions + * @brief RTC Time and Date functions + * +@verbatim + =============================================================================== + ##### RTC Time and Date functions ##### + =============================================================================== + + [..] This section provides functions allowing to configure Time and Date features + +@endverbatim + * @{ + */ + +/** + * @brief Sets RTC current time. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param sTime: Pointer to Time structure + * @param Format: Specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format) +{ + uint32_t tmpreg = 0U; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + assert_param(IS_RTC_DAYLIGHT_SAVING(sTime->DayLightSaving)); + assert_param(IS_RTC_STORE_OPERATION(sTime->StoreOperation)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + if(Format == RTC_FORMAT_BIN) + { + if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + assert_param(IS_RTC_HOUR12(sTime->Hours)); + assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat)); + } + else + { + sTime->TimeFormat = 0x00U; + assert_param(IS_RTC_HOUR24(sTime->Hours)); + } + assert_param(IS_RTC_MINUTES(sTime->Minutes)); + assert_param(IS_RTC_SECONDS(sTime->Seconds)); + + tmpreg = (uint32_t)(((uint32_t)RTC_ByteToBcd2(sTime->Hours) << 16U) | \ + ((uint32_t)RTC_ByteToBcd2(sTime->Minutes) << 8U) | \ + ((uint32_t)RTC_ByteToBcd2(sTime->Seconds)) | \ + (((uint32_t)sTime->TimeFormat) << 16U)); + } + else + { + if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + tmpreg = RTC_Bcd2ToByte(sTime->Hours); + assert_param(IS_RTC_HOUR12(tmpreg)); + assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat)); + } + else + { + sTime->TimeFormat = 0x00U; + assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sTime->Hours))); + } + assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sTime->Minutes))); + assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sTime->Seconds))); + tmpreg = (((uint32_t)(sTime->Hours) << 16U) | \ + ((uint32_t)(sTime->Minutes) << 8U) | \ + ((uint32_t)sTime->Seconds) | \ + ((uint32_t)(sTime->TimeFormat) << 16U)); + } + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Set Initialization mode */ + if(RTC_EnterInitMode(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Set RTC state */ + hrtc->State = HAL_RTC_STATE_ERROR; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_ERROR; + } + else + { + /* Set the RTC_TR register */ + hrtc->Instance->TR = (uint32_t)(tmpreg & RTC_TR_RESERVED_MASK); + + /* Clear the bits to be configured */ + hrtc->Instance->CR &= (uint32_t)~RTC_CR_BCK; + + /* Configure the RTC_CR register */ + hrtc->Instance->CR |= (uint32_t)(sTime->DayLightSaving | sTime->StoreOperation); + + /* Exit Initialization mode */ + hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; + + /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ + if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) + { + if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_ERROR; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_ERROR; + } + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + __HAL_UNLOCK(hrtc); + + return HAL_OK; + } +} + +/** + * @brief Gets RTC current time. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param sTime: Pointer to Time structure + * @param Format: Specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @note You can use SubSeconds and SecondFraction (sTime structure fields returned) to convert SubSeconds + * value in second fraction ratio with time unit following generic formula: + * Second fraction ratio * time_unit= [(SecondFraction-SubSeconds)/(SecondFraction+1)] * time_unit + * This conversion can be performed only if no shift operation is pending (ie. SHFP=0) when PREDIV_S >= SS + * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values + * in the higher-order calendar shadow registers to ensure consistency between the time and date values. + * Reading RTC current time locks the values in calendar shadow registers until current date is read. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format) +{ + uint32_t tmpreg = 0U; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + + /* Get subseconds structure field from the corresponding register */ + sTime->SubSeconds = (uint32_t)(hrtc->Instance->SSR); + + /* Get SecondFraction structure field from the corresponding register field*/ + sTime->SecondFraction = (uint32_t)(hrtc->Instance->PRER & RTC_PRER_PREDIV_S); + + /* Get the TR register */ + tmpreg = (uint32_t)(hrtc->Instance->TR & RTC_TR_RESERVED_MASK); + + /* Fill the structure fields with the read parameters */ + sTime->Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> 16U); + sTime->Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >>8U); + sTime->Seconds = (uint8_t)(tmpreg & (RTC_TR_ST | RTC_TR_SU)); + sTime->TimeFormat = (uint8_t)((tmpreg & (RTC_TR_PM)) >> 16U); + + /* Check the input parameters format */ + if(Format == RTC_FORMAT_BIN) + { + /* Convert the time structure parameters to Binary format */ + sTime->Hours = (uint8_t)RTC_Bcd2ToByte(sTime->Hours); + sTime->Minutes = (uint8_t)RTC_Bcd2ToByte(sTime->Minutes); + sTime->Seconds = (uint8_t)RTC_Bcd2ToByte(sTime->Seconds); + } + + return HAL_OK; +} + +/** + * @brief Sets RTC current date. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param sDate: Pointer to date structure + * @param Format: specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format) +{ + uint32_t datetmpreg = 0U; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + if((Format == RTC_FORMAT_BIN) && ((sDate->Month & 0x10U) == 0x10U)) + { + sDate->Month = (uint8_t)((sDate->Month & (uint8_t)~(0x10U)) + (uint8_t)0x0AU); + } + + assert_param(IS_RTC_WEEKDAY(sDate->WeekDay)); + + if(Format == RTC_FORMAT_BIN) + { + assert_param(IS_RTC_YEAR(sDate->Year)); + assert_param(IS_RTC_MONTH(sDate->Month)); + assert_param(IS_RTC_DATE(sDate->Date)); + + datetmpreg = (((uint32_t)RTC_ByteToBcd2(sDate->Year) << 16U) | \ + ((uint32_t)RTC_ByteToBcd2(sDate->Month) << 8U) | \ + ((uint32_t)RTC_ByteToBcd2(sDate->Date)) | \ + ((uint32_t)sDate->WeekDay << 13U)); + } + else + { + assert_param(IS_RTC_YEAR(RTC_Bcd2ToByte(sDate->Year))); + datetmpreg = RTC_Bcd2ToByte(sDate->Month); + assert_param(IS_RTC_MONTH(datetmpreg)); + datetmpreg = RTC_Bcd2ToByte(sDate->Date); + assert_param(IS_RTC_DATE(datetmpreg)); + + datetmpreg = ((((uint32_t)sDate->Year) << 16U) | \ + (((uint32_t)sDate->Month) << 8U) | \ + ((uint32_t)sDate->Date) | \ + (((uint32_t)sDate->WeekDay) << 13U)); + } + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Set Initialization mode */ + if(RTC_EnterInitMode(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Set RTC state*/ + hrtc->State = HAL_RTC_STATE_ERROR; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_ERROR; + } + else + { + /* Set the RTC_DR register */ + hrtc->Instance->DR = (uint32_t)(datetmpreg & RTC_DR_RESERVED_MASK); + + /* Exit Initialization mode */ + hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; + + /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ + if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) + { + if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_ERROR; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_ERROR; + } + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY ; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; + } +} + +/** + * @brief Gets RTC current date. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param sDate: Pointer to Date structure + * @param Format: Specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values + * in the higher-order calendar shadow registers to ensure consistency between the time and date values. + * Reading RTC current time locks the values in calendar shadow registers until Current date is read. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_GetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format) +{ + uint32_t datetmpreg = 0U; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + + /* Get the DR register */ + datetmpreg = (uint32_t)(hrtc->Instance->DR & RTC_DR_RESERVED_MASK); + + /* Fill the structure fields with the read parameters */ + sDate->Year = (uint8_t)((datetmpreg & (RTC_DR_YT | RTC_DR_YU)) >> 16U); + sDate->Month = (uint8_t)((datetmpreg & (RTC_DR_MT | RTC_DR_MU)) >> 8U); + sDate->Date = (uint8_t)(datetmpreg & (RTC_DR_DT | RTC_DR_DU)); + sDate->WeekDay = (uint8_t)((datetmpreg & (RTC_DR_WDU)) >> 13U); + + /* Check the input parameters format */ + if(Format == RTC_FORMAT_BIN) + { + /* Convert the date structure parameters to Binary format */ + sDate->Year = (uint8_t)RTC_Bcd2ToByte(sDate->Year); + sDate->Month = (uint8_t)RTC_Bcd2ToByte(sDate->Month); + sDate->Date = (uint8_t)RTC_Bcd2ToByte(sDate->Date); + } + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup RTC_Exported_Functions_Group3 RTC Alarm functions + * @brief RTC Alarm functions + * +@verbatim + =============================================================================== + ##### RTC Alarm functions ##### + =============================================================================== + + [..] This section provides functions allowing to configure Alarm feature + +@endverbatim + * @{ + */ +/** + * @brief Sets the specified RTC Alarm. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param sAlarm: Pointer to Alarm structure + * @param Format: Specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_SetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format) +{ + uint32_t tickstart = 0U; + uint32_t tmpreg = 0U, subsecondtmpreg = 0U; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + assert_param(IS_RTC_ALARM(sAlarm->Alarm)); + assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask)); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel)); + assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds)); + assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + if(Format == RTC_FORMAT_BIN) + { + if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours)); + assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); + } + else + { + sAlarm->AlarmTime.TimeFormat = 0x00U; + assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours)); + } + assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes)); + assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds)); + + if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) + { + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay)); + } + else + { + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay)); + } + + tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16U) | \ + ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8U) | \ + ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \ + ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ + ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24U) | \ + ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ + ((uint32_t)sAlarm->AlarmMask)); + } + else + { + if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours); + assert_param(IS_RTC_HOUR12(tmpreg)); + assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); + } + else + { + sAlarm->AlarmTime.TimeFormat = 0x00U; + assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); + } + + assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes))); + assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds))); + + if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) + { + tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(tmpreg)); + } + else + { + tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(tmpreg)); + } + + tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16U) | \ + ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8U) | \ + ((uint32_t) sAlarm->AlarmTime.Seconds) | \ + ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ + ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24U) | \ + ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ + ((uint32_t)sAlarm->AlarmMask)); + } + + /* Configure the Alarm A or Alarm B Sub Second registers */ + subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask)); + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Configure the Alarm register */ + if(sAlarm->Alarm == RTC_ALARM_A) + { + /* Disable the Alarm A interrupt */ + __HAL_RTC_ALARMA_DISABLE(hrtc); + + /* In case of interrupt mode is used, the interrupt source must disabled */ + __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */ + while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET) + { + if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + + hrtc->Instance->ALRMAR = (uint32_t)tmpreg; + /* Configure the Alarm A Sub Second register */ + hrtc->Instance->ALRMASSR = subsecondtmpreg; + /* Configure the Alarm state: Enable Alarm */ + __HAL_RTC_ALARMA_ENABLE(hrtc); + } + else + { + /* Disable the Alarm B interrupt */ + __HAL_RTC_ALARMB_DISABLE(hrtc); + + /* In case of interrupt mode is used, the interrupt source must disabled */ + __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRB); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */ + while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET) + { + if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + + hrtc->Instance->ALRMBR = (uint32_t)tmpreg; + /* Configure the Alarm B Sub Second register */ + hrtc->Instance->ALRMBSSR = subsecondtmpreg; + /* Configure the Alarm state: Enable Alarm */ + __HAL_RTC_ALARMB_ENABLE(hrtc); + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Sets the specified RTC Alarm with Interrupt + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param sAlarm: Pointer to Alarm structure + * @param Format: Specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_SetAlarm_IT(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format) +{ + uint32_t tmpreg = 0U, subsecondtmpreg = 0U; + __IO uint32_t count = RTC_TIMEOUT_VALUE * (SystemCoreClock / 32U / 1000U) ; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + assert_param(IS_RTC_ALARM(sAlarm->Alarm)); + assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask)); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel)); + assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds)); + assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + if(Format == RTC_FORMAT_BIN) + { + if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours)); + assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); + } + else + { + sAlarm->AlarmTime.TimeFormat = 0x00U; + assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours)); + } + assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes)); + assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds)); + + if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) + { + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay)); + } + else + { + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay)); + } + tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16U) | \ + ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8U) | \ + ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \ + ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ + ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24U) | \ + ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ + ((uint32_t)sAlarm->AlarmMask)); + } + else + { + if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) + { + tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours); + assert_param(IS_RTC_HOUR12(tmpreg)); + assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); + } + else + { + sAlarm->AlarmTime.TimeFormat = 0x00U; + assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); + } + + assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes))); + assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds))); + + if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) + { + tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(tmpreg)); + } + else + { + tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); + assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(tmpreg)); + } + tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16U) | \ + ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8U) | \ + ((uint32_t) sAlarm->AlarmTime.Seconds) | \ + ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ + ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24U) | \ + ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ + ((uint32_t)sAlarm->AlarmMask)); + } + /* Configure the Alarm A or Alarm B Sub Second registers */ + subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask)); + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Configure the Alarm register */ + if(sAlarm->Alarm == RTC_ALARM_A) + { + /* Disable the Alarm A interrupt */ + __HAL_RTC_ALARMA_DISABLE(hrtc); + + /* Clear flag alarm A */ + __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF); + + /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */ + do + { + if (count-- == 0) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + while (__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET); + + hrtc->Instance->ALRMAR = (uint32_t)tmpreg; + /* Configure the Alarm A Sub Second register */ + hrtc->Instance->ALRMASSR = subsecondtmpreg; + /* Configure the Alarm state: Enable Alarm */ + __HAL_RTC_ALARMA_ENABLE(hrtc); + /* Configure the Alarm interrupt */ + __HAL_RTC_ALARM_ENABLE_IT(hrtc,RTC_IT_ALRA); + } + else + { + /* Disable the Alarm B interrupt */ + __HAL_RTC_ALARMB_DISABLE(hrtc); + + /* Clear flag alarm B */ + __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF); + + /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */ + do + { + if (count-- == 0) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + while (__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET); + + hrtc->Instance->ALRMBR = (uint32_t)tmpreg; + /* Configure the Alarm B Sub Second register */ + hrtc->Instance->ALRMBSSR = subsecondtmpreg; + /* Configure the Alarm state: Enable Alarm */ + __HAL_RTC_ALARMB_ENABLE(hrtc); + /* Configure the Alarm interrupt */ + __HAL_RTC_ALARM_ENABLE_IT(hrtc, RTC_IT_ALRB); + } + + /* RTC Alarm Interrupt Configuration: EXTI configuration */ + __HAL_RTC_ALARM_EXTI_ENABLE_IT(); + + EXTI->RTSR |= RTC_EXTI_LINE_ALARM_EVENT; + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Deactivate the specified RTC Alarm + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param Alarm: Specifies the Alarm. + * This parameter can be one of the following values: + * @arg RTC_ALARM_A: AlarmA + * @arg RTC_ALARM_B: AlarmB + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_DeactivateAlarm(RTC_HandleTypeDef *hrtc, uint32_t Alarm) +{ + uint32_t tickstart = 0U; + + /* Check the parameters */ + assert_param(IS_RTC_ALARM(Alarm)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + if(Alarm == RTC_ALARM_A) + { + /* AlarmA */ + __HAL_RTC_ALARMA_DISABLE(hrtc); + + /* In case of interrupt mode is used, the interrupt source must disabled */ + __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */ + while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET) + { + if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + } + else + { + /* AlarmB */ + __HAL_RTC_ALARMB_DISABLE(hrtc); + + /* In case of interrupt mode is used, the interrupt source must disabled */ + __HAL_RTC_ALARM_DISABLE_IT(hrtc,RTC_IT_ALRB); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */ + while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET) + { + if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + } + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Gets the RTC Alarm value and masks. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param sAlarm: Pointer to Date structure + * @param Alarm: Specifies the Alarm. + * This parameter can be one of the following values: + * @arg RTC_ALARM_A: AlarmA + * @arg RTC_ALARM_B: AlarmB + * @param Format: Specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_GetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Alarm, uint32_t Format) +{ + uint32_t tmpreg = 0U, subsecondtmpreg = 0U; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + assert_param(IS_RTC_ALARM(Alarm)); + + if(Alarm == RTC_ALARM_A) + { + /* AlarmA */ + sAlarm->Alarm = RTC_ALARM_A; + + tmpreg = (uint32_t)(hrtc->Instance->ALRMAR); + subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMASSR ) & RTC_ALRMASSR_SS); + } + else + { + sAlarm->Alarm = RTC_ALARM_B; + + tmpreg = (uint32_t)(hrtc->Instance->ALRMBR); + subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMBSSR) & RTC_ALRMBSSR_SS); + } + + /* Fill the structure with the read parameters */ + sAlarm->AlarmTime.Hours = (uint32_t)((tmpreg & (RTC_ALRMAR_HT | RTC_ALRMAR_HU)) >> 16U); + sAlarm->AlarmTime.Minutes = (uint32_t)((tmpreg & (RTC_ALRMAR_MNT | RTC_ALRMAR_MNU)) >> 8U); + sAlarm->AlarmTime.Seconds = (uint32_t)(tmpreg & (RTC_ALRMAR_ST | RTC_ALRMAR_SU)); + sAlarm->AlarmTime.TimeFormat = (uint32_t)((tmpreg & RTC_ALRMAR_PM) >> 16U); + sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg; + sAlarm->AlarmDateWeekDay = (uint32_t)((tmpreg & (RTC_ALRMAR_DT | RTC_ALRMAR_DU)) >> 24U); + sAlarm->AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMAR_WDSEL); + sAlarm->AlarmMask = (uint32_t)(tmpreg & RTC_ALARMMASK_ALL); + + if(Format == RTC_FORMAT_BIN) + { + sAlarm->AlarmTime.Hours = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours); + sAlarm->AlarmTime.Minutes = RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes); + sAlarm->AlarmTime.Seconds = RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds); + sAlarm->AlarmDateWeekDay = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); + } + + return HAL_OK; +} + +/** + * @brief This function handles Alarm interrupt request. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval None + */ +void HAL_RTC_AlarmIRQHandler(RTC_HandleTypeDef* hrtc) +{ + if(__HAL_RTC_ALARM_GET_IT(hrtc, RTC_IT_ALRA)) + { + /* Get the status of the Interrupt */ + if((uint32_t)(hrtc->Instance->CR & RTC_IT_ALRA) != (uint32_t)RESET) + { + /* AlarmA callback */ + HAL_RTC_AlarmAEventCallback(hrtc); + + /* Clear the Alarm interrupt pending bit */ + __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRAF); + } + } + + if(__HAL_RTC_ALARM_GET_IT(hrtc, RTC_IT_ALRB)) + { + /* Get the status of the Interrupt */ + if((uint32_t)(hrtc->Instance->CR & RTC_IT_ALRB) != (uint32_t)RESET) + { + /* AlarmB callback */ + HAL_RTCEx_AlarmBEventCallback(hrtc); + + /* Clear the Alarm interrupt pending bit */ + __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRBF); + } + } + + /* Clear the EXTI's line Flag for RTC Alarm */ + __HAL_RTC_ALARM_EXTI_CLEAR_FLAG(); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; +} + +/** + * @brief Alarm A callback. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval None + */ +__weak void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RTC_AlarmAEventCallback could be implemented in the user file + */ +} + +/** + * @brief This function handles AlarmA Polling request. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @param Timeout: Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_PollForAlarmAEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) +{ + uint32_t tickstart = 0U; + + /* Get tick */ + tickstart = HAL_GetTick(); + + while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAF) == RESET) + { + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout)) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + } + + /* Clear the Alarm interrupt pending bit */ + __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup RTC_Exported_Functions_Group4 Peripheral Control functions + * @brief Peripheral Control functions + * +@verbatim + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides functions allowing to + (+) Wait for RTC Time and Date Synchronization + +@endverbatim + * @{ + */ + +/** + * @brief Waits until the RTC Time and Date registers (RTC_TR and RTC_DR) are + * synchronized with RTC APB clock. + * @note The RTC Resynchronization mode is write protected, use the + * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function. + * @note To read the calendar through the shadow registers after Calendar + * initialization, calendar update or after wake-up from low power modes + * the software must first clear the RSF flag. + * The software must then wait until it is set again before reading + * the calendar, which means that the calendar registers have been + * correctly copied into the RTC_TR and RTC_DR shadow registers. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTC_WaitForSynchro(RTC_HandleTypeDef* hrtc) +{ + uint32_t tickstart = 0U; + + /* Clear RSF flag */ + hrtc->Instance->ISR &= (uint32_t)RTC_RSF_MASK; + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait the registers to be synchronised */ + while((hrtc->Instance->ISR & RTC_ISR_RSF) == (uint32_t)RESET) + { + if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup RTC_Exported_Functions_Group5 Peripheral State functions + * @brief Peripheral State functions + * +@verbatim + =============================================================================== + ##### Peripheral State functions ##### + =============================================================================== + [..] + This subsection provides functions allowing to + (+) Get RTC state + +@endverbatim + * @{ + */ +/** + * @brief Returns the RTC state. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval HAL state + */ +HAL_RTCStateTypeDef HAL_RTC_GetState(RTC_HandleTypeDef* hrtc) +{ + return hrtc->State; +} + +/** + * @} + */ + +/** + * @brief Enters the RTC Initialization mode. + * @note The RTC Initialization mode is write protected, use the + * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function. + * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains + * the configuration information for RTC. + * @retval HAL status + */ +HAL_StatusTypeDef RTC_EnterInitMode(RTC_HandleTypeDef* hrtc) +{ + uint32_t tickstart = 0U; + + /* Check if the Initialization mode is set */ + if((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET) + { + /* Set the Initialization mode */ + hrtc->Instance->ISR = (uint32_t)RTC_INIT_MASK; + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait till RTC is in INIT state and if Time out is reached exit */ + while((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET) + { + if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + return HAL_OK; +} + + +/** + * @brief Converts a 2 digit decimal to BCD format. + * @param Value: Byte to be converted + * @retval Converted byte + */ +uint8_t RTC_ByteToBcd2(uint8_t Value) +{ + uint32_t bcdhigh = 0U; + + while(Value >= 10U) + { + bcdhigh++; + Value -= 10U; + } + + return ((uint8_t)(bcdhigh << 4U) | Value); +} + +/** + * @brief Converts from 2 digit BCD to Binary. + * @param Value: BCD value to be converted + * @retval Converted word + */ +uint8_t RTC_Bcd2ToByte(uint8_t Value) +{ + uint32_t tmp = 0U; + tmp = ((uint8_t)(Value & (uint8_t)0xF0U) >> (uint8_t)0x4U) * 10U; + return (tmp + (Value & (uint8_t)0x0FU)); +} + +/** + * @} + */ + +#endif /* HAL_RTC_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/