Mouse code for the MacroRat
Diff: mbed-dev/targets/TARGET_NORDIC/TARGET_MCU_NRF51822/TARGET_WALLBOT_BLE/PinNames.h
- Revision:
- 18:6a4db94011d3
diff -r f713758f6238 -r 6a4db94011d3 mbed-dev/targets/TARGET_NORDIC/TARGET_MCU_NRF51822/TARGET_WALLBOT_BLE/PinNames.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev/targets/TARGET_NORDIC/TARGET_MCU_NRF51822/TARGET_WALLBOT_BLE/PinNames.h Sun May 14 23:18:57 2017 +0000 @@ -0,0 +1,180 @@ +/* mbed Microcontroller Library + * Copyright (c) 2013 Nordic Semiconductor + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +#ifndef MBED_PINNAMES_H +#define MBED_PINNAMES_H + +#include "cmsis.h" + +#ifdef __cplusplus +extern "C" { +#endif + +typedef enum { + PIN_INPUT, + PIN_OUTPUT +} PinDirection; + +typedef enum { + p0 = 0, + p1 = 1, + p2 = 2, + p3 = 3, + p4 = 4, + p5 = 5, + p6 = 6, + p7 = 7, + p8 = 8, + p9 = 9, + p10 = 10, + p11 = 11, + p12 = 12, + p13 = 13, + p14 = 14, + p15 = 15, + p16 = 16, + p17 = 17, + p18 = 18, + p19 = 19, + p20 = 20, + p21 = 21, + p22 = 22, + p23 = 23, + p24 = 24, + p25 = 25, + p26 = 26, + p27 = 27, + p28 = 28, + p29 = 29, + p30 = 30, + + P0_0 = p0, + P0_1 = p1, + P0_2 = p2, + P0_3 = p3, + P0_4 = p4, + P0_5 = p5, + P0_6 = p6, + P0_7 = p7, + + P0_8 = p8, + P0_9 = p9, + P0_10 = p10, + P0_11 = p11, + P0_12 = p12, + P0_13 = p13, + P0_14 = p14, + P0_15 = p15, + + P0_16 = p16, + P0_17 = p17, + P0_18 = p18, + P0_19 = p19, + P0_20 = p20, + P0_21 = p21, + P0_22 = p22, + P0_23 = p23, + + P0_24 = p24, + P0_25 = p25, + P0_26 = p26, + P0_27 = p27, + P0_28 = p28, + P0_29 = p29, + P0_30 = p30, + + LED1 = p18, + LED2 = p19, + LED3 = p18, + LED4 = p19, + + BUTTON1 = p16, + BUTTON2 = p17, + + RX_PIN_NUMBER = p11, + TX_PIN_NUMBER = p9, + CTS_PIN_NUMBER = 31, // unused + RTS_PIN_NUMBER = 31, // unused + + // mbed interface pins + USBTX = TX_PIN_NUMBER, + USBRX = RX_PIN_NUMBER, + + SPI_PSELMOSI0 = p20, + SPI_PSELMISO0 = p22, + SPI_PSELSS0 = p24, + SPI_PSELSCK0 = p25, + + SPI_PSELMOSI1 = p12, + SPI_PSELMISO1 = p13, + SPI_PSELSS1 = p14, + SPI_PSELSCK1 = p15, + + SPIS_PSELMOSI = p12, + SPIS_PSELMISO = p13, + SPIS_PSELSS = p14, + SPIS_PSELSCK = p15, + + LED_CONNECT = P0_18, + LED_MODE = P0_19, + OUT_LOW= P0_20, + SW1 = P0_16, + SW2 = P0_17, + + R_PWM = P0_28, + R_IN1 = P0_30, + R_IN2 = P0_0, + L_PWM = P0_29, + L_IN1 = P0_23, + L_IN2 = P0_24, + + MMC_SCK = P0_15, + MMC_CS = P0_14, + MMC_SDO = P0_13, + MMC_SDI = P0_12, + + R_ENC1 = P0_8, + R_ENC2 = P0_10, + L_ENC1 = P0_6, + L_ENC2 = P0_7, + + P1IN = P0_2, + P2IN = P0_3, + P3IN = P0_4, + P4IN = P0_5, + + I2C_SCL = P0_21, + I2C_SDA = P0_22, + + I2C_SCL0 = P0_21, //required definition for the i2c patch + I2C_SDA0 = P0_22, //required definition for the i2c patch + + // Not connected + NC = (int)0xFFFFFFFF + +} PinName; + +typedef enum { + PullNone = 0, + PullDown = 1, + PullUp = 3, + PullDefault = PullUp +} PinMode; + +#ifdef __cplusplus +} +#endif + +#endif