Mouse code for the MacroRat
Diff: mbed-dev/targets/TARGET_Atmel/TARGET_SAM_CortexM0P/drivers/system/clock/TARGET_SAMR21/clock.c
- Revision:
- 18:6a4db94011d3
diff -r f713758f6238 -r 6a4db94011d3 mbed-dev/targets/TARGET_Atmel/TARGET_SAM_CortexM0P/drivers/system/clock/TARGET_SAMR21/clock.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev/targets/TARGET_Atmel/TARGET_SAM_CortexM0P/drivers/system/clock/TARGET_SAMR21/clock.c Sun May 14 23:18:57 2017 +0000 @@ -0,0 +1,1031 @@ +/** + * \file + * + * \brief SAM D21/R21/DA0/DA1 Clock Driver + * + * Copyright (C) 2013-2015 Atmel Corporation. All rights reserved. + * + * \asf_license_start + * + * \page License + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * + * 3. The name of Atmel may not be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * 4. This software may only be redistributed and used in connection with an + * Atmel microcontroller product. + * + * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE + * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR + * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + * \asf_license_stop + * + */ +/* + * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a> + */ +#include <clock.h> +#include <conf_clocks.h> +#include <system.h> + +#ifndef SYSCTRL_FUSES_OSC32K_ADDR +#if (SAMR21) || (SAMD) +# define SYSCTRL_FUSES_OSC32K_ADDR FUSES_OSC32K_CAL_ADDR +# define SYSCTRL_FUSES_OSC32K_Pos FUSES_OSC32K_CAL_Pos +#elif (SAML21) +# define SYSCTRL_FUSES_OSC32K_ADDR NVMCTRL_OTP4 +# define SYSCTRL_FUSES_OSC32K_Pos 6 + +#else +# define SYSCTRL_FUSES_OSC32K_ADDR SYSCTRL_FUSES_OSC32K_CAL_ADDR +# define SYSCTRL_FUSES_OSC32K_Pos SYSCTRL_FUSES_OSC32K_CAL_Pos +#endif +#endif + +/** + * \internal + * \brief DFLL-specific data container. + */ +struct _system_clock_dfll_config { + uint32_t control; + uint32_t val; + uint32_t mul; +}; + +/** + * \internal + * \brief DPLL-specific data container. + */ +struct _system_clock_dpll_config { + uint32_t frequency; +}; + + +/** + * \internal + * \brief XOSC-specific data container. + */ +struct _system_clock_xosc_config { + uint32_t frequency; +}; + +/** + * \internal + * \brief System clock module data container. + */ +struct _system_clock_module { + volatile struct _system_clock_dfll_config dfll; + +#ifdef FEATURE_SYSTEM_CLOCK_DPLL + volatile struct _system_clock_dpll_config dpll; +#endif + + volatile struct _system_clock_xosc_config xosc; + volatile struct _system_clock_xosc_config xosc32k; +}; + +/** + * \internal + * \brief Internal module instance to cache configuration values. + */ +static struct _system_clock_module _system_clock_inst = { + .dfll = { + .control = 0, + .val = 0, + .mul = 0, + }, + +#ifdef FEATURE_SYSTEM_CLOCK_DPLL + .dpll = { + .frequency = 0, + }, +#endif + .xosc = { + .frequency = 0, + }, + .xosc32k = { + .frequency = 0, + }, +}; + +/** + * \internal + * \brief Wait for sync to the DFLL control registers. + */ +static inline void _system_dfll_wait_for_sync(void) +{ + while (!(SYSCTRL->PCLKSR.reg & SYSCTRL_PCLKSR_DFLLRDY)) { + /* Wait for DFLL sync */ + } +} + +/** + * \internal + * \brief Wait for sync to the OSC32K control registers. + */ +static inline void _system_osc32k_wait_for_sync(void) +{ + while (!(SYSCTRL->PCLKSR.reg & SYSCTRL_PCLKSR_OSC32KRDY)) { + /* Wait for OSC32K sync */ + } +} + +static inline void _system_clock_source_dfll_set_config_errata_9905(void) +{ + + /* Disable ONDEMAND mode while writing configurations */ + SYSCTRL->DFLLCTRL.reg = _system_clock_inst.dfll.control & ~SYSCTRL_DFLLCTRL_ONDEMAND; + _system_dfll_wait_for_sync(); + + SYSCTRL->DFLLMUL.reg = _system_clock_inst.dfll.mul; + SYSCTRL->DFLLVAL.reg = _system_clock_inst.dfll.val; + + /* Write full configuration to DFLL control register */ + SYSCTRL->DFLLCTRL.reg = _system_clock_inst.dfll.control; +} + +/** + * \brief Retrieve the frequency of a clock source. + * + * Determines the current operating frequency of a given clock source. + * + * \param[in] clock_source Clock source to get the frequency + * + * \returns Frequency of the given clock source, in Hz. + */ +uint32_t system_clock_source_get_hz( + const enum system_clock_source clock_source) +{ + switch (clock_source) { + case SYSTEM_CLOCK_SOURCE_XOSC: + return _system_clock_inst.xosc.frequency; + + case SYSTEM_CLOCK_SOURCE_OSC8M: + return 8000000UL >> SYSCTRL->OSC8M.bit.PRESC; + + case SYSTEM_CLOCK_SOURCE_OSC32K: + return 32768UL; + + case SYSTEM_CLOCK_SOURCE_ULP32K: + return 32768UL; + + case SYSTEM_CLOCK_SOURCE_XOSC32K: + return _system_clock_inst.xosc32k.frequency; + + case SYSTEM_CLOCK_SOURCE_DFLL: + + /* Check if the DFLL has been configured */ + if (!(_system_clock_inst.dfll.control & SYSCTRL_DFLLCTRL_ENABLE)) + return 0; + + /* Make sure that the DFLL module is ready */ + _system_dfll_wait_for_sync(); + + /* Check if operating in closed loop mode */ + if (_system_clock_inst.dfll.control & SYSCTRL_DFLLCTRL_MODE) { + return system_gclk_chan_get_hz(SYSCTRL_GCLK_ID_DFLL48) * + (_system_clock_inst.dfll.mul & 0xffff); + } + + return 48000000UL; + +#ifdef FEATURE_SYSTEM_CLOCK_DPLL + case SYSTEM_CLOCK_SOURCE_DPLL: + if (!(SYSCTRL->DPLLSTATUS.reg & SYSCTRL_DPLLSTATUS_ENABLE)) { + return 0; + } + + return _system_clock_inst.dpll.frequency; +#endif + + default: + return 0; + } +} + +/** + * \brief Configure the internal OSC8M oscillator clock source. + * + * Configures the 8MHz (nominal) internal RC oscillator with the given + * configuration settings. + * + * \param[in] config OSC8M configuration structure containing the new config + */ +void system_clock_source_osc8m_set_config( + struct system_clock_source_osc8m_config *const config) +{ + SYSCTRL_OSC8M_Type temp = SYSCTRL->OSC8M; + + /* Use temporary struct to reduce register access */ + temp.bit.PRESC = config->prescaler; + temp.bit.ONDEMAND = config->on_demand; + temp.bit.RUNSTDBY = config->run_in_standby; + + SYSCTRL->OSC8M = temp; +} + +/** + * \brief Configure the internal OSC32K oscillator clock source. + * + * Configures the 32KHz (nominal) internal RC oscillator with the given + * configuration settings. + * + * \param[in] config OSC32K configuration structure containing the new config + */ +void system_clock_source_osc32k_set_config( + struct system_clock_source_osc32k_config *const config) +{ + SYSCTRL_OSC32K_Type temp = SYSCTRL->OSC32K; + + /* Update settings via a temporary struct to reduce register access */ + temp.bit.EN1K = config->enable_1khz_output; + temp.bit.EN32K = config->enable_32khz_output; + temp.bit.STARTUP = config->startup_time; + temp.bit.ONDEMAND = config->on_demand; + temp.bit.RUNSTDBY = config->run_in_standby; + temp.bit.WRTLOCK = config->write_once; + + SYSCTRL->OSC32K = temp; +} + +/** + * \brief Configure the external oscillator clock source. + * + * Configures the external oscillator clock source with the given configuration + * settings. + * + * \param[in] config External oscillator configuration structure containing + * the new config + */ +void system_clock_source_xosc_set_config( + struct system_clock_source_xosc_config *const config) +{ + SYSCTRL_XOSC_Type temp = SYSCTRL->XOSC; + + temp.bit.STARTUP = config->startup_time; + + if (config->external_clock == SYSTEM_CLOCK_EXTERNAL_CRYSTAL) { + temp.bit.XTALEN = 1; + } else { + temp.bit.XTALEN = 0; + } + + temp.bit.AMPGC = config->auto_gain_control; + + /* Set gain if automatic gain control is not selected */ + if (!config->auto_gain_control) { + if (config->frequency <= 2000000) { + temp.bit.GAIN = 0; + } else if (config->frequency <= 4000000) { + temp.bit.GAIN = 1; + } else if (config->frequency <= 8000000) { + temp.bit.GAIN = 2; + } else if (config->frequency <= 16000000) { + temp.bit.GAIN = 3; + } else if (config->frequency <= 30000000) { + temp.bit.GAIN = 4; + } + + } + + temp.bit.ONDEMAND = config->on_demand; + temp.bit.RUNSTDBY = config->run_in_standby; + + /* Store XOSC frequency for internal use */ + _system_clock_inst.xosc.frequency = config->frequency; + + SYSCTRL->XOSC = temp; +} + +/** + * \brief Configure the XOSC32K external 32KHz oscillator clock source. + * + * Configures the external 32KHz oscillator clock source with the given + * configuration settings. + * + * \param[in] config XOSC32K configuration structure containing the new config + */ +void system_clock_source_xosc32k_set_config( + struct system_clock_source_xosc32k_config *const config) +{ + SYSCTRL_XOSC32K_Type temp = SYSCTRL->XOSC32K; + + temp.bit.STARTUP = config->startup_time; + + if (config->external_clock == SYSTEM_CLOCK_EXTERNAL_CRYSTAL) { + temp.bit.XTALEN = 1; + } else { + temp.bit.XTALEN = 0; + } + + temp.bit.AAMPEN = config->auto_gain_control; + temp.bit.EN1K = config->enable_1khz_output; + temp.bit.EN32K = config->enable_32khz_output; + + temp.bit.ONDEMAND = config->on_demand; + temp.bit.RUNSTDBY = config->run_in_standby; + temp.bit.WRTLOCK = config->write_once; + + /* Cache the new frequency in case the user needs to check the current + * operating frequency later */ + _system_clock_inst.xosc32k.frequency = config->frequency; + + SYSCTRL->XOSC32K = temp; +} + +/** + * \brief Configure the DFLL clock source. + * + * Configures the Digital Frequency Locked Loop clock source with the given + * configuration settings. + * + * \note The DFLL will be running when this function returns, as the DFLL module + * needs to be enabled in order to perform the module configuration. + * + * \param[in] config DFLL configuration structure containing the new config + */ +void system_clock_source_dfll_set_config( + struct system_clock_source_dfll_config *const config) +{ + _system_clock_inst.dfll.val = + SYSCTRL_DFLLVAL_COARSE(config->coarse_value) | + SYSCTRL_DFLLVAL_FINE(config->fine_value); + + _system_clock_inst.dfll.control = + (uint32_t)config->wakeup_lock | + (uint32_t)config->stable_tracking | + (uint32_t)config->quick_lock | + (uint32_t)config->chill_cycle | + ((uint32_t)config->on_demand << SYSCTRL_DFLLCTRL_ONDEMAND_Pos); + + if (config->loop_mode == SYSTEM_CLOCK_DFLL_LOOP_MODE_CLOSED) { + + _system_clock_inst.dfll.mul = + SYSCTRL_DFLLMUL_CSTEP(config->coarse_max_step) | + SYSCTRL_DFLLMUL_FSTEP(config->fine_max_step) | + SYSCTRL_DFLLMUL_MUL(config->multiply_factor); + + /* Enable the closed loop mode */ + _system_clock_inst.dfll.control |= config->loop_mode; + } + if (config->loop_mode == SYSTEM_CLOCK_DFLL_LOOP_MODE_USB_RECOVERY) { + + _system_clock_inst.dfll.mul = + SYSCTRL_DFLLMUL_MUL(config->multiply_factor); + + /* Enable the USB recovery mode */ + _system_clock_inst.dfll.control |= config->loop_mode | + SYSCTRL_DFLLCTRL_BPLCKC; + } +} + +#ifdef FEATURE_SYSTEM_CLOCK_DPLL +/** + * \brief Configure the DPLL clock source. + * + * Configures the Digital Phase-Locked Loop clock source with the given + * configuration settings. + * + * \note The DPLL will be running when this function returns, as the DPLL module + * needs to be enabled in order to perform the module configuration. + * + * \param[in] config DPLL configuration structure containing the new config + */ +void system_clock_source_dpll_set_config( + struct system_clock_source_dpll_config *const config) +{ + + uint32_t tmpldr; + uint8_t tmpldrfrac; + uint32_t refclk; + + refclk = config->reference_frequency; + + /* Only reference clock REF1 can be divided */ + if (config->reference_clock == SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_XOSC) { + refclk = refclk / (2 * (config->reference_divider + 1)); + } + + /* Calculate LDRFRAC and LDR */ + tmpldr = (config->output_frequency << 4) / refclk; + tmpldrfrac = tmpldr & 0x0f; + tmpldr = (tmpldr >> 4) - 1; + + SYSCTRL->DPLLCTRLA.reg = + ((uint32_t)config->on_demand << SYSCTRL_DPLLCTRLA_ONDEMAND_Pos) | + ((uint32_t)config->run_in_standby << SYSCTRL_DPLLCTRLA_RUNSTDBY_Pos); + + SYSCTRL->DPLLRATIO.reg = + SYSCTRL_DPLLRATIO_LDRFRAC(tmpldrfrac) | + SYSCTRL_DPLLRATIO_LDR(tmpldr); + + SYSCTRL->DPLLCTRLB.reg = + SYSCTRL_DPLLCTRLB_DIV(config->reference_divider) | + ((uint32_t)config->lock_bypass << SYSCTRL_DPLLCTRLB_LBYPASS_Pos) | + SYSCTRL_DPLLCTRLB_LTIME(config->lock_time) | + SYSCTRL_DPLLCTRLB_REFCLK(config->reference_clock) | + ((uint32_t)config->wake_up_fast << SYSCTRL_DPLLCTRLB_WUF_Pos) | + ((uint32_t)config->low_power_enable << SYSCTRL_DPLLCTRLB_LPEN_Pos) | + SYSCTRL_DPLLCTRLB_FILTER(config->filter); + + /* + * Fck = Fckrx * (LDR + 1 + LDRFRAC / 16) + */ + _system_clock_inst.dpll.frequency = + (refclk * (((tmpldr + 1) << 4) + tmpldrfrac)) >> 4; +} +#endif + +/** + * \brief Writes the calibration values for a given oscillator clock source. + * + * Writes an oscillator calibration value to the given oscillator control + * registers. The acceptable ranges are: + * + * For OSC32K: + * - 7 bits (max value 128) + * For OSC8MHZ: + * - 8 bits (Max value 255) + * For OSCULP: + * - 5 bits (Max value 32) + * + * \note The frequency range parameter applies only when configuring the 8MHz + * oscillator and will be ignored for the other oscillators. + * + * \param[in] clock_source Clock source to calibrate + * \param[in] calibration_value Calibration value to write + * \param[in] freq_range Frequency range (8MHz oscillator only) + * + * \retval STATUS_OK The calibration value was written + * successfully. + * \retval STATUS_ERR_INVALID_ARG The setting is not valid for selected clock + * source. + */ +enum status_code system_clock_source_write_calibration( + const enum system_clock_source clock_source, + const uint16_t calibration_value, + const uint8_t freq_range) +{ + switch (clock_source) { + case SYSTEM_CLOCK_SOURCE_OSC8M: + + if (calibration_value > 0xfff || freq_range > 4) { + return STATUS_ERR_INVALID_ARG; + } + + SYSCTRL->OSC8M.bit.CALIB = calibration_value; + SYSCTRL->OSC8M.bit.FRANGE = freq_range; + break; + + case SYSTEM_CLOCK_SOURCE_OSC32K: + + if (calibration_value > 128) { + return STATUS_ERR_INVALID_ARG; + } + + _system_osc32k_wait_for_sync(); + SYSCTRL->OSC32K.bit.CALIB = calibration_value; + break; + + case SYSTEM_CLOCK_SOURCE_ULP32K: + + if (calibration_value > 32) { + return STATUS_ERR_INVALID_ARG; + } + + SYSCTRL->OSCULP32K.bit.CALIB = calibration_value; + break; + + default: + Assert(false); + return STATUS_ERR_INVALID_ARG; + + } + + return STATUS_OK; +} + +/** + * \brief Enables a clock source. + * + * Enables a clock source which has been previously configured. + * + * \param[in] clock_source Clock source to enable + * + * \retval STATUS_OK Clock source was enabled successfully and + * is ready + * \retval STATUS_ERR_INVALID_ARG The clock source is not available on this + * device + */ +enum status_code system_clock_source_enable( + const enum system_clock_source clock_source) +{ + switch (clock_source) { + case SYSTEM_CLOCK_SOURCE_OSC8M: + SYSCTRL->OSC8M.reg |= SYSCTRL_OSC8M_ENABLE; + return STATUS_OK; + + case SYSTEM_CLOCK_SOURCE_OSC32K: + SYSCTRL->OSC32K.reg |= SYSCTRL_OSC32K_ENABLE; + break; + + case SYSTEM_CLOCK_SOURCE_XOSC: + SYSCTRL->XOSC.reg |= SYSCTRL_XOSC_ENABLE; + break; + + case SYSTEM_CLOCK_SOURCE_XOSC32K: + SYSCTRL->XOSC32K.reg |= SYSCTRL_XOSC32K_ENABLE; + break; + + case SYSTEM_CLOCK_SOURCE_DFLL: + _system_clock_inst.dfll.control |= SYSCTRL_DFLLCTRL_ENABLE; + _system_clock_source_dfll_set_config_errata_9905(); + break; + +#ifdef FEATURE_SYSTEM_CLOCK_DPLL + case SYSTEM_CLOCK_SOURCE_DPLL: + SYSCTRL->DPLLCTRLA.reg |= SYSCTRL_DPLLCTRLA_ENABLE; + break; +#endif + + case SYSTEM_CLOCK_SOURCE_ULP32K: + /* Always enabled */ + return STATUS_OK; + + default: + Assert(false); + return STATUS_ERR_INVALID_ARG; + } + + return STATUS_OK; + } + + /** + * \brief Disables a clock source. + * + * Disables a clock source that was previously enabled. + * + * \param[in] clock_source Clock source to disable + * + * \retval STATUS_OK Clock source was disabled successfully + * \retval STATUS_ERR_INVALID_ARG An invalid or unavailable clock source was + * given + */ + enum status_code system_clock_source_disable( + const enum system_clock_source clock_source) +{ + switch (clock_source) { + case SYSTEM_CLOCK_SOURCE_OSC8M: + SYSCTRL->OSC8M.reg &= ~SYSCTRL_OSC8M_ENABLE; + break; + + case SYSTEM_CLOCK_SOURCE_OSC32K: + SYSCTRL->OSC32K.reg &= ~SYSCTRL_OSC32K_ENABLE; + break; + + case SYSTEM_CLOCK_SOURCE_XOSC: + SYSCTRL->XOSC.reg &= ~SYSCTRL_XOSC_ENABLE; + break; + + case SYSTEM_CLOCK_SOURCE_XOSC32K: + SYSCTRL->XOSC32K.reg &= ~SYSCTRL_XOSC32K_ENABLE; + break; + + case SYSTEM_CLOCK_SOURCE_DFLL: + _system_clock_inst.dfll.control &= ~SYSCTRL_DFLLCTRL_ENABLE; + SYSCTRL->DFLLCTRL.reg = _system_clock_inst.dfll.control; + break; + +#ifdef FEATURE_SYSTEM_CLOCK_DPLL + case SYSTEM_CLOCK_SOURCE_DPLL: + SYSCTRL->DPLLCTRLA.reg &= ~SYSCTRL_DPLLCTRLA_ENABLE; + break; +#endif + + case SYSTEM_CLOCK_SOURCE_ULP32K: + /* Not possible to disable */ + + default: + Assert(false); + return STATUS_ERR_INVALID_ARG; + + } + + return STATUS_OK; + } + + /** + * \brief Checks if a clock source is ready. + * + * Checks if a given clock source is ready to be used. + * + * \param[in] clock_source Clock source to check if ready + * + * \returns Ready state of the given clock source. + * + * \retval true Clock source is enabled and ready + * \retval false Clock source is disabled or not yet ready + */ + bool system_clock_source_is_ready( + const enum system_clock_source clock_source) +{ + uint32_t mask = 0; + + switch (clock_source) { + case SYSTEM_CLOCK_SOURCE_OSC8M: + mask = SYSCTRL_PCLKSR_OSC8MRDY; + break; + + case SYSTEM_CLOCK_SOURCE_OSC32K: + mask = SYSCTRL_PCLKSR_OSC32KRDY; + break; + + case SYSTEM_CLOCK_SOURCE_XOSC: + mask = SYSCTRL_PCLKSR_XOSCRDY; + break; + + case SYSTEM_CLOCK_SOURCE_XOSC32K: + mask = SYSCTRL_PCLKSR_XOSC32KRDY; + break; + + case SYSTEM_CLOCK_SOURCE_DFLL: + if (CONF_CLOCK_DFLL_LOOP_MODE == SYSTEM_CLOCK_DFLL_LOOP_MODE_CLOSED) { + mask = (SYSCTRL_PCLKSR_DFLLRDY | + SYSCTRL_PCLKSR_DFLLLCKF | SYSCTRL_PCLKSR_DFLLLCKC); + } else { + mask = SYSCTRL_PCLKSR_DFLLRDY; + } + break; + +#ifdef FEATURE_SYSTEM_CLOCK_DPLL + case SYSTEM_CLOCK_SOURCE_DPLL: + return ((SYSCTRL->DPLLSTATUS.reg & + (SYSCTRL_DPLLSTATUS_CLKRDY | SYSCTRL_DPLLSTATUS_LOCK)) == + (SYSCTRL_DPLLSTATUS_CLKRDY | SYSCTRL_DPLLSTATUS_LOCK)); +#endif + + case SYSTEM_CLOCK_SOURCE_ULP32K: + /* Not possible to disable */ + return true; + + default: + return false; + } + + return ((SYSCTRL->PCLKSR.reg & mask) == mask); +} + +/* Include some checks for conf_clocks.h validation */ +#include "clock_config_check.h" + +#if !defined(__DOXYGEN__) +/** \internal + * + * Configures a Generic Clock Generator with the configuration from \c conf_clocks.h. + */ +# define _CONF_CLOCK_GCLK_CONFIG(n, unused) \ + if (CONF_CLOCK_GCLK_##n##_ENABLE == true) { \ + struct system_gclk_gen_config gclk_conf; \ + system_gclk_gen_get_config_defaults(&gclk_conf); \ + gclk_conf.source_clock = CONF_CLOCK_GCLK_##n##_CLOCK_SOURCE; \ + gclk_conf.division_factor = CONF_CLOCK_GCLK_##n##_PRESCALER; \ + gclk_conf.run_in_standby = CONF_CLOCK_GCLK_##n##_RUN_IN_STANDBY; \ + gclk_conf.output_enable = CONF_CLOCK_GCLK_##n##_OUTPUT_ENABLE; \ + system_gclk_gen_set_config(GCLK_GENERATOR_##n, &gclk_conf); \ + system_gclk_gen_enable(GCLK_GENERATOR_##n); \ + } + +/** \internal + * + * Configures a Generic Clock Generator with the configuration from \c conf_clocks.h, + * provided that it is not the main Generic Clock Generator channel. + */ +# define _CONF_CLOCK_GCLK_CONFIG_NONMAIN(n, unused) \ + if (n > 0) { _CONF_CLOCK_GCLK_CONFIG(n, unused); } +#endif + +/** \internal + * + * Switch all peripheral clock to a not enabled general clock + * to save power. + */ +static void _switch_peripheral_gclk(void) +{ + uint32_t gclk_id; + struct system_gclk_chan_config gclk_conf; + +#if CONF_CLOCK_GCLK_1_ENABLE == false + gclk_conf.source_generator = GCLK_GENERATOR_1; +#elif CONF_CLOCK_GCLK_2_ENABLE == false + gclk_conf.source_generator = GCLK_GENERATOR_2; +#elif CONF_CLOCK_GCLK_3_ENABLE == false + gclk_conf.source_generator = GCLK_GENERATOR_3; +#elif CONF_CLOCK_GCLK_4_ENABLE == false + gclk_conf.source_generator = GCLK_GENERATOR_4; +#elif CONF_CLOCK_GCLK_5_ENABLE == false + gclk_conf.source_generator = GCLK_GENERATOR_5; +#elif CONF_CLOCK_GCLK_6_ENABLE == false + gclk_conf.source_generator = GCLK_GENERATOR_6; +#elif CONF_CLOCK_GCLK_7_ENABLE == false + gclk_conf.source_generator = GCLK_GENERATOR_7; +#else + gclk_conf.source_generator = GCLK_GENERATOR_7; +#endif + + for (gclk_id = 0; gclk_id < GCLK_NUM; gclk_id++) { + system_gclk_chan_set_config(gclk_id, &gclk_conf); + } +} + +/** + * \brief Initialize clock system based on the configuration in conf_clocks.h. + * + * This function will apply the settings in conf_clocks.h when run from the user + * application. All clock sources and GCLK generators are running when this function + * returns. + * + * \note OSC8M is always enabled and if user selects other clocks for GCLK generators, + * the OSC8M default enable can be disabled after system_clock_init. Make sure the + * clock switch successfully before disabling OSC8M. + */ +void system_clock_init(void) +{ + /* Various bits in the INTFLAG register can be set to one at startup. + This will ensure that these bits are cleared */ + SYSCTRL->INTFLAG.reg = SYSCTRL_INTFLAG_BOD33RDY | SYSCTRL_INTFLAG_BOD33DET | + SYSCTRL_INTFLAG_DFLLRDY; + + system_flash_set_waitstates(CONF_CLOCK_FLASH_WAIT_STATES); + + /* Switch all peripheral clock to a not enabled general clock to save power. */ + _switch_peripheral_gclk(); + + /* XOSC */ +#if CONF_CLOCK_XOSC_ENABLE == true + struct system_clock_source_xosc_config xosc_conf; + system_clock_source_xosc_get_config_defaults(&xosc_conf); + + xosc_conf.external_clock = CONF_CLOCK_XOSC_EXTERNAL_CRYSTAL; + xosc_conf.startup_time = CONF_CLOCK_XOSC_STARTUP_TIME; + xosc_conf.auto_gain_control = CONF_CLOCK_XOSC_AUTO_GAIN_CONTROL; + xosc_conf.frequency = CONF_CLOCK_XOSC_EXTERNAL_FREQUENCY; + xosc_conf.on_demand = CONF_CLOCK_XOSC_ON_DEMAND; + xosc_conf.run_in_standby = CONF_CLOCK_XOSC_RUN_IN_STANDBY; + + system_clock_source_xosc_set_config(&xosc_conf); + system_clock_source_enable(SYSTEM_CLOCK_SOURCE_XOSC); +#endif + + + /* XOSC32K */ +#if CONF_CLOCK_XOSC32K_ENABLE == true + struct system_clock_source_xosc32k_config xosc32k_conf; + system_clock_source_xosc32k_get_config_defaults(&xosc32k_conf); + + xosc32k_conf.frequency = 32768UL; + xosc32k_conf.external_clock = CONF_CLOCK_XOSC32K_EXTERNAL_CRYSTAL; + xosc32k_conf.startup_time = CONF_CLOCK_XOSC32K_STARTUP_TIME; + xosc32k_conf.auto_gain_control = CONF_CLOCK_XOSC32K_AUTO_AMPLITUDE_CONTROL; + xosc32k_conf.enable_1khz_output = CONF_CLOCK_XOSC32K_ENABLE_1KHZ_OUPUT; + xosc32k_conf.enable_32khz_output = CONF_CLOCK_XOSC32K_ENABLE_32KHZ_OUTPUT; + xosc32k_conf.on_demand = false; + xosc32k_conf.run_in_standby = CONF_CLOCK_XOSC32K_RUN_IN_STANDBY; + + system_clock_source_xosc32k_set_config(&xosc32k_conf); + system_clock_source_enable(SYSTEM_CLOCK_SOURCE_XOSC32K); + while(!system_clock_source_is_ready(SYSTEM_CLOCK_SOURCE_XOSC32K)); + if (CONF_CLOCK_XOSC32K_ON_DEMAND) { + SYSCTRL->XOSC32K.bit.ONDEMAND = 1; + } +#endif + + + /* OSCK32K */ +#if CONF_CLOCK_OSC32K_ENABLE == true + SYSCTRL->OSC32K.bit.CALIB = + ((*(uint32_t *)SYSCTRL_FUSES_OSC32K_ADDR >> + SYSCTRL_FUSES_OSC32K_Pos) & 0x7Ful); + + struct system_clock_source_osc32k_config osc32k_conf; + system_clock_source_osc32k_get_config_defaults(&osc32k_conf); + + osc32k_conf.startup_time = CONF_CLOCK_OSC32K_STARTUP_TIME; + osc32k_conf.enable_1khz_output = CONF_CLOCK_OSC32K_ENABLE_1KHZ_OUTPUT; + osc32k_conf.enable_32khz_output = CONF_CLOCK_OSC32K_ENABLE_32KHZ_OUTPUT; + osc32k_conf.on_demand = CONF_CLOCK_OSC32K_ON_DEMAND; + osc32k_conf.run_in_standby = CONF_CLOCK_OSC32K_RUN_IN_STANDBY; + + system_clock_source_osc32k_set_config(&osc32k_conf); + system_clock_source_enable(SYSTEM_CLOCK_SOURCE_OSC32K); +#endif + + + /* DFLL Config (Open and Closed Loop) */ +#if CONF_CLOCK_DFLL_ENABLE == true + struct system_clock_source_dfll_config dfll_conf; + system_clock_source_dfll_get_config_defaults(&dfll_conf); + + dfll_conf.loop_mode = CONF_CLOCK_DFLL_LOOP_MODE; + dfll_conf.on_demand = false; + + /* Using DFLL48M COARSE CAL value from NVM Software Calibration Area Mapping + in DFLL.COARSE helps to output a frequency close to 48 MHz.*/ +#define NVM_DFLL_COARSE_POS 58 /* DFLL48M Coarse calibration value bit position.*/ +#define NVM_DFLL_COARSE_SIZE 6 /* DFLL48M Coarse calibration value bit size.*/ + + uint32_t coarse =( *((uint32_t *)(NVMCTRL_OTP4) + + (NVM_DFLL_COARSE_POS / 32)) + >> (NVM_DFLL_COARSE_POS % 32)) + & ((1 << NVM_DFLL_COARSE_SIZE) - 1); + /* In some revision chip, the coarse calibration value is not correct. */ + if (coarse == 0x3f) { + coarse = 0x1f; + } + dfll_conf.coarse_value = coarse; + + if (CONF_CLOCK_DFLL_LOOP_MODE == SYSTEM_CLOCK_DFLL_LOOP_MODE_OPEN) { + dfll_conf.fine_value = CONF_CLOCK_DFLL_FINE_VALUE; + } + +# if CONF_CLOCK_DFLL_QUICK_LOCK == true + dfll_conf.quick_lock = SYSTEM_CLOCK_DFLL_QUICK_LOCK_ENABLE; +# else + dfll_conf.quick_lock = SYSTEM_CLOCK_DFLL_QUICK_LOCK_DISABLE; +# endif + +# if CONF_CLOCK_DFLL_TRACK_AFTER_FINE_LOCK == true + dfll_conf.stable_tracking = SYSTEM_CLOCK_DFLL_STABLE_TRACKING_TRACK_AFTER_LOCK; +# else + dfll_conf.stable_tracking = SYSTEM_CLOCK_DFLL_STABLE_TRACKING_FIX_AFTER_LOCK; +# endif + +# if CONF_CLOCK_DFLL_KEEP_LOCK_ON_WAKEUP == true + dfll_conf.wakeup_lock = SYSTEM_CLOCK_DFLL_WAKEUP_LOCK_KEEP; +# else + dfll_conf.wakeup_lock = SYSTEM_CLOCK_DFLL_WAKEUP_LOCK_LOSE; +# endif + +# if CONF_CLOCK_DFLL_ENABLE_CHILL_CYCLE == true + dfll_conf.chill_cycle = SYSTEM_CLOCK_DFLL_CHILL_CYCLE_ENABLE; +# else + dfll_conf.chill_cycle = SYSTEM_CLOCK_DFLL_CHILL_CYCLE_DISABLE; +# endif + + if (CONF_CLOCK_DFLL_LOOP_MODE == SYSTEM_CLOCK_DFLL_LOOP_MODE_CLOSED) { + dfll_conf.multiply_factor = CONF_CLOCK_DFLL_MULTIPLY_FACTOR; + } + + dfll_conf.coarse_max_step = CONF_CLOCK_DFLL_MAX_COARSE_STEP_SIZE; + dfll_conf.fine_max_step = CONF_CLOCK_DFLL_MAX_FINE_STEP_SIZE; + + if (CONF_CLOCK_DFLL_LOOP_MODE == SYSTEM_CLOCK_DFLL_LOOP_MODE_USB_RECOVERY) { + dfll_conf.fine_value = 0x1ff; + dfll_conf.quick_lock = SYSTEM_CLOCK_DFLL_QUICK_LOCK_ENABLE; + dfll_conf.stable_tracking = SYSTEM_CLOCK_DFLL_STABLE_TRACKING_FIX_AFTER_LOCK; + dfll_conf.wakeup_lock = SYSTEM_CLOCK_DFLL_WAKEUP_LOCK_KEEP; + dfll_conf.chill_cycle = SYSTEM_CLOCK_DFLL_CHILL_CYCLE_DISABLE; + + dfll_conf.multiply_factor = 48000; + } + + system_clock_source_dfll_set_config(&dfll_conf); +#endif + + + /* OSC8M */ + struct system_clock_source_osc8m_config osc8m_conf; + system_clock_source_osc8m_get_config_defaults(&osc8m_conf); + + osc8m_conf.prescaler = CONF_CLOCK_OSC8M_PRESCALER; + osc8m_conf.on_demand = CONF_CLOCK_OSC8M_ON_DEMAND; + osc8m_conf.run_in_standby = CONF_CLOCK_OSC8M_RUN_IN_STANDBY; + + system_clock_source_osc8m_set_config(&osc8m_conf); + system_clock_source_enable(SYSTEM_CLOCK_SOURCE_OSC8M); + + + /* GCLK */ +#if CONF_CLOCK_CONFIGURE_GCLK == true + system_gclk_init(); + + /* Configure all GCLK generators except for the main generator, which + * is configured later after all other clock systems are set up */ + MREPEAT(GCLK_GEN_NUM, _CONF_CLOCK_GCLK_CONFIG_NONMAIN, ~); + +# if CONF_CLOCK_DFLL_ENABLE == true + /* Enable DFLL reference clock if in closed loop mode */ + if (CONF_CLOCK_DFLL_LOOP_MODE == SYSTEM_CLOCK_DFLL_LOOP_MODE_CLOSED) { + struct system_gclk_chan_config dfll_gclk_chan_conf; + + system_gclk_chan_get_config_defaults(&dfll_gclk_chan_conf); + dfll_gclk_chan_conf.source_generator = CONF_CLOCK_DFLL_SOURCE_GCLK_GENERATOR; + system_gclk_chan_set_config(SYSCTRL_GCLK_ID_DFLL48, &dfll_gclk_chan_conf); + system_gclk_chan_enable(SYSCTRL_GCLK_ID_DFLL48); + } +# endif + +# if CONF_CLOCK_DPLL_ENABLE == true + /* Enable DPLL internal lock timer and reference clock */ + struct system_gclk_chan_config dpll_gclk_chan_conf; + system_gclk_chan_get_config_defaults(&dpll_gclk_chan_conf); + if (CONF_CLOCK_DPLL_LOCK_TIME != SYSTEM_CLOCK_SOURCE_DPLL_LOCK_TIME_DEFAULT) { + dpll_gclk_chan_conf.source_generator = CONF_CLOCK_DPLL_LOCK_GCLK_GENERATOR; + system_gclk_chan_set_config(SYSCTRL_GCLK_ID_FDPLL32K, &dpll_gclk_chan_conf); + system_gclk_chan_enable(SYSCTRL_GCLK_ID_FDPLL32K); + } + + if (CONF_CLOCK_DPLL_REFERENCE_CLOCK == SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_GCLK) { + dpll_gclk_chan_conf.source_generator = CONF_CLOCK_DPLL_REFERENCE_GCLK_GENERATOR; + system_gclk_chan_set_config(SYSCTRL_GCLK_ID_FDPLL, &dpll_gclk_chan_conf); + system_gclk_chan_enable(SYSCTRL_GCLK_ID_FDPLL); + } +# endif +#endif + + + /* DFLL Enable (Open and Closed Loop) */ +#if CONF_CLOCK_DFLL_ENABLE == true + system_clock_source_enable(SYSTEM_CLOCK_SOURCE_DFLL); + while(!system_clock_source_is_ready(SYSTEM_CLOCK_SOURCE_DFLL)); + if (CONF_CLOCK_DFLL_ON_DEMAND) { + SYSCTRL->DFLLCTRL.bit.ONDEMAND = 1; + } +#endif + + /* DPLL */ +#ifdef FEATURE_SYSTEM_CLOCK_DPLL +# if (CONF_CLOCK_DPLL_ENABLE == true) + + /* Enable DPLL reference clock */ + if (CONF_CLOCK_DPLL_REFERENCE_CLOCK == SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_XOSC32K) { + /* XOSC32K should have been enabled for DPLL_REF0 */ + Assert(CONF_CLOCK_XOSC32K_ENABLE); + } else if (CONF_CLOCK_DPLL_REFERENCE_CLOCK == SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_XOSC) { + /* XOSC should have been enabled for DPLL_REF1 */ + Assert(CONF_CLOCK_XOSC_ENABLE); + } else if (CONF_CLOCK_DPLL_REFERENCE_CLOCK == SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_GCLK) { + /* GCLK should have been enabled */ + Assert(CONF_CLOCK_CONFIGURE_GCLK); + } else { + Assert(false); + } + + struct system_clock_source_dpll_config dpll_config; + system_clock_source_dpll_get_config_defaults(&dpll_config); + + dpll_config.on_demand = false; + dpll_config.run_in_standby = CONF_CLOCK_DPLL_RUN_IN_STANDBY; + dpll_config.lock_bypass = CONF_CLOCK_DPLL_LOCK_BYPASS; + dpll_config.wake_up_fast = CONF_CLOCK_DPLL_WAKE_UP_FAST; + dpll_config.low_power_enable = CONF_CLOCK_DPLL_LOW_POWER_ENABLE; + + dpll_config.filter = CONF_CLOCK_DPLL_FILTER; + dpll_config.lock_time = CONF_CLOCK_DPLL_LOCK_TIME; + + dpll_config.reference_clock = CONF_CLOCK_DPLL_REFERENCE_CLOCK; + dpll_config.reference_frequency = CONF_CLOCK_DPLL_REFERENCE_FREQUENCY; + dpll_config.reference_divider = CONF_CLOCK_DPLL_REFERENCE_DIVIDER; + dpll_config.output_frequency = CONF_CLOCK_DPLL_OUTPUT_FREQUENCY; + + system_clock_source_dpll_set_config(&dpll_config); + system_clock_source_enable(SYSTEM_CLOCK_SOURCE_DPLL); + while(!system_clock_source_is_ready(SYSTEM_CLOCK_SOURCE_DPLL)); + if (CONF_CLOCK_DPLL_ON_DEMAND) { + SYSCTRL->DPLLCTRLA.bit.ONDEMAND = 1; + } + +# endif +#endif + + /* CPU and BUS clocks */ + system_cpu_clock_set_divider(CONF_CLOCK_CPU_DIVIDER); + + system_apb_clock_set_divider(SYSTEM_CLOCK_APB_APBA, CONF_CLOCK_APBA_DIVIDER); + system_apb_clock_set_divider(SYSTEM_CLOCK_APB_APBB, CONF_CLOCK_APBB_DIVIDER); + system_apb_clock_set_divider(SYSTEM_CLOCK_APB_APBC, CONF_CLOCK_APBC_DIVIDER); + + /* GCLK 0 */ +#if CONF_CLOCK_CONFIGURE_GCLK == true + /* Configure the main GCLK last as it might depend on other generators */ + _CONF_CLOCK_GCLK_CONFIG(0, ~); +#endif +}