Mouse code for the MacroRat
Diff: mbed-dev/drivers/Ethernet.h
- Revision:
- 18:6a4db94011d3
diff -r f713758f6238 -r 6a4db94011d3 mbed-dev/drivers/Ethernet.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev/drivers/Ethernet.h Sun May 14 23:18:57 2017 +0000 @@ -0,0 +1,176 @@ +/* mbed Microcontroller Library + * Copyright (c) 2006-2013 ARM Limited + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +#ifndef MBED_ETHERNET_H +#define MBED_ETHERNET_H + +#include "platform/platform.h" + +#if DEVICE_ETHERNET + +namespace mbed { +/** \addtogroup drivers */ +/** @{*/ + +/** An ethernet interface, to use with the ethernet pins. + * + * @Note Synchronization level: Not protected + * + * Example: + * @code + * // Read destination and source from every ethernet packet + * + * #include "mbed.h" + * + * Ethernet eth; + * + * int main() { + * char buf[0x600]; + * + * while(1) { + * int size = eth.receive(); + * if(size > 0) { + * eth.read(buf, size); + * printf("Destination: %02X:%02X:%02X:%02X:%02X:%02X\n", + * buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]); + * printf("Source: %02X:%02X:%02X:%02X:%02X:%02X\n", + * buf[6], buf[7], buf[8], buf[9], buf[10], buf[11]); + * } + * + * wait(1); + * } + * } + * @endcode + */ +class Ethernet { + +public: + + /** Initialise the ethernet interface. + */ + Ethernet(); + + /** Powers the hardware down. + */ + virtual ~Ethernet(); + + enum Mode { + AutoNegotiate, + HalfDuplex10, + FullDuplex10, + HalfDuplex100, + FullDuplex100 + }; + + /** Writes into an outgoing ethernet packet. + * + * It will append size bytes of data to the previously written bytes. + * + * @param data An array to write. + * @param size The size of data. + * + * @returns + * The number of written bytes. + */ + int write(const char *data, int size); + + /** Send an outgoing ethernet packet. + * + * After filling in the data in an ethernet packet it must be send. + * Send will provide a new packet to write to. + * + * @returns + * 0 if the sending was failed, + * or the size of the packet successfully sent. + */ + int send(); + + /** Recevies an arrived ethernet packet. + * + * Receiving an ethernet packet will drop the last received ethernet packet + * and make a new ethernet packet ready to read. + * If no ethernet packet is arrived it will return 0. + * + * @returns + * 0 if no ethernet packet is arrived, + * or the size of the arrived packet. + */ + int receive(); + + /** Read from an recevied ethernet packet. + * + * After receive returnd a number bigger than 0it is + * possible to read bytes from this packet. + * Read will write up to size bytes into data. + * + * It is possible to use read multible times. + * Each time read will start reading after the last read byte before. + * + * @returns + * The number of byte read. + */ + int read(char *data, int size); + + /** Gives the ethernet address of the mbed. + * + * @param mac Must be a pointer to a 6 byte char array to copy the ethernet address in. + */ + void address(char *mac); + + /** Returns if an ethernet link is pressent or not. It takes a wile after Ethernet initializion to show up. + * + * @returns + * 0 if no ethernet link is pressent, + * 1 if an ethernet link is pressent. + * + * Example: + * @code + * // Using the Ethernet link function + * #include "mbed.h" + * + * Ethernet eth; + * + * int main() { + * wait(1); // Needed after startup. + * if (eth.link()) { + * printf("online\n"); + * } else { + * printf("offline\n"); + * } + * } + * @endcode + */ + int link(); + + /** Sets the speed and duplex parameters of an ethernet link + * + * - AutoNegotiate Auto negotiate speed and duplex + * - HalfDuplex10 10 Mbit, half duplex + * - FullDuplex10 10 Mbit, full duplex + * - HalfDuplex100 100 Mbit, half duplex + * - FullDuplex100 100 Mbit, full duplex + * + * @param mode the speed and duplex mode to set the link to: + */ + void set_link(Mode mode); +}; + +} // namespace mbed + +#endif + +#endif + +/** @}*/