Mouse code for the MacroRat
mbed-dev/targets/TARGET_NUVOTON/TARGET_NUC472/device/StdDriver/nuc472_uart.h
- Committer:
- sahilmgandhi
- Date:
- 2017-06-03
- Revision:
- 46:b156ef445742
- Parent:
- 18:6a4db94011d3
File content as of revision 46:b156ef445742:
/**************************************************************************//** * @file uart.h * @version V1.00 * $Revision: 20 $ * $Date: 15/11/30 1:35p $ * @brief NUC472/NUC442 UART driver header file * * @note * Copyright (C) 2013 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #ifndef __UART_H__ #define __UART_H__ #ifdef __cplusplus extern "C" { #endif /** @addtogroup NUC472_442_Device_Driver NUC472/NUC442 Device Driver @{ */ /** @addtogroup NUC472_442_UART_Driver UART Driver @{ */ /** @addtogroup NUC472_442_UART_EXPORTED_CONSTANTS UART Exported Constants @{ */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_FCR constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_FIFO_RFITL_1BYTE (0x0 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 1 byte */ #define UART_FIFO_RFITL_4BYTES (0x1 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 4 bytes */ #define UART_FIFO_RFITL_8BYTES (0x2 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 8 bytes */ #define UART_FIFO_RFITL_14BYTES (0x3 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 14 bytes */ #define UART_FIFO_RTSTRGLV_1BYTE (0x0 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 1 byte */ #define UART_FIFO_RTSTRGLV_4BYTES (0x1 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 4 bytes */ #define UART_FIFO_RTSTRGLV_8BYTES (0x2 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 8 bytes */ #define UART_FIFO_RTSTRGLV_14BYTES (0x3 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 14 bytes */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_LCR constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_WORD_LEN_5 (0) /*!< UART_LINE setting to set UART word length to 5 bits */ #define UART_WORD_LEN_6 (1) /*!< UART_LINE setting to set UART word length to 6 bits */ #define UART_WORD_LEN_7 (2) /*!< UART_LINE setting to set UART word length to 7 bits */ #define UART_WORD_LEN_8 (3) /*!< UART_LINE setting to set UART word length to 8 bits */ #define UART_PARITY_NONE (0x0 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to set UART as no parity */ #define UART_PARITY_ODD (0x1 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to set UART as odd parity */ #define UART_PARITY_EVEN (0x3 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to set UART as even parity */ #define UART_PARITY_MARK (0x5 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to keep parity bit as '1' */ #define UART_PARITY_SPACE (0x7 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to keep parity bit as '0' */ #define UART_STOP_BIT_1 (0x0 << UART_LINE_NSB_Pos) /*!< UART_LINE setting for one stop bit */ #define UART_STOP_BIT_1_5 (0x1 << UART_LINE_NSB_Pos) /*!< UART_LINE setting for 1.5 stop bit when 5-bit word length */ #define UART_STOP_BIT_2 (0x1 << UART_LINE_NSB_Pos) /*!< UART_LINE setting for two stop bit when 6, 7, 8-bit word length */ /*---------------------------------------------------------------------------------------------------------*/ /* UART RTS LEVEL TRIGGER constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_RTS_IS_HIGH_LEV_TRG (0x1 << UART_MODEM_RTSACTLV_Pos) /*!< Set RTS is High Level Trigger */ #define UART_RTS_IS_LOW_LEV_TRG (0x0 << UART_MODEM_RTSACTLV_Pos) /*!< Set RTS is Low Level Trigger */ /*---------------------------------------------------------------------------------------------------------*/ /* UART CTS LEVEL TRIGGER constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_CTS_IS_HIGH_LEV_TRG (0x1 << UART_MODEMSTS_CTSACTLV_Pos) /*!< Set CTS is High Level Trigger */ #define UART_CTS_IS_LOW_LEV_TRG (0x0 << UART_MODEMSTS_CTSACTLV_Pos) /*!< Set CTS is Low Level Trigger */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_FUNC_SEL constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_FUNCSEL_UART (0x0 << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_FUNCSEL setting to set UART Function (Default) */ #define UART_FUNCSEL_IrDA (0x2 << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_FUNCSEL setting to set IrDA Function */ #define UART_FUNCSEL_RS485 (0x3 << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_FUNCSEL setting to set RS485 Function */ /*---------------------------------------------------------------------------------------------------------*/ /* UART BAUDRATE MODE constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_BAUD_MODE0 (0) /*!< Set UART Baudrate Mode is Mode0 */ #define UART_BAUD_MODE2 (UART_BAUD_BAUDM1_Msk | UART_BAUD_BAUDM0_Msk) /*!< Set UART Baudrate Mode is Mode2 */ /*@}*/ /* end of group NUC472_442_UART_EXPORTED_CONSTANTS */ /** @addtogroup NUC472_442_UART_EXPORTED_FUNCTIONS UART Exported Functions @{ */ /** * @brief Calculate UART baudrate mode0 divider * * @param[in] u32SrcFreq UART clock frequency * @param[in] u32BaudRate Baudrate of UART module * * @return UART baudrate mode0 divider * \hideinitializer * */ #define UART_BAUD_MODE0_DIVIDER(u32SrcFreq, u32BaudRate) (((u32SrcFreq + (u32BaudRate*8)) / u32BaudRate >> 4)-2) /** * @brief Calculate UART baudrate mode2 divider * * @param[in] u32SrcFreq UART clock frequency * @param[in] u32BaudRate Baudrate of UART module * * @return UART baudrate mode2 divider * \hideinitializer */ #define UART_BAUD_MODE2_DIVIDER(u32SrcFreq, u32BaudRate) (((u32SrcFreq + (u32BaudRate/2)) / u32BaudRate)-2) /** * @brief Write Data to Tx data register * * @param[in] uart The base address of UART module. * @param[in] u8Data Data byte to transmit * * @return None * \hideinitializer */ #define UART_WRITE(uart, u8Data) (uart->DAT = (u8Data)) /** * @brief Read Rx data register * * @param[in] uart The base address of UART module. * * @return The oldest data byte in RX FIFO * \hideinitializer */ #define UART_READ(uart) (uart->DAT) /** * @brief Get Tx empty register value. * * @param[in] uart The base address of UART module * * @return Tx empty register value. * \hideinitializer */ #define UART_GET_TX_EMPTY(uart) (uart->FIFOSTS & UART_FIFOSTS_TXEMPTY_Msk) /** * @brief Get Rx empty register value. * * @param[in] uart The base address of UART module * * @return Rx empty register value. * \hideinitializer */ #define UART_GET_RX_EMPTY(uart) (uart->FIFOSTS & UART_FIFOSTS_RXEMPTY_Msk) /** * @brief Check specified uart port transmission is over. * * @param[in] uart The base address of UART module * * @return TE_Flag. * \hideinitializer */ #define UART_IS_TX_EMPTY(uart) ((uart->FIFOSTS & UART_FIFOSTS_TXEMPTYF_Msk) >> UART_FIFOSTS_TXEMPTYF_Pos) /** * @brief Wait specified uart port transmission is over * * @param[in] uart The base address of UART module * * @return None * \hideinitializer */ #define UART_WAIT_TX_EMPTY(uart) while(!(((uart->FIFOSTS) & UART_FIFOSTS_TXEMPTYF_Msk) >> UART_FIFOSTS_TXEMPTYF_Pos)) /** * @brief Check RDA_IF is set or not * * @param[in] uart The base address of UART module * * @return * 0 : The number of bytes in the RX FIFO is less than the RFITL * 1 : The number of bytes in the RX FIFO equals or larger than RFITL * \hideinitializer */ #define UART_IS_RX_READY(uart) ((uart->INTSTS & UART_INTSTS_RDAIF_Msk)>>UART_INTSTS_RDAIF_Pos) /** * @brief Check TX FIFO is full or not * * @param[in] uart The base address of UART module * * @return * 1 = TX FIFO is full * 0 = TX FIFO is not full * \hideinitializer */ #define UART_IS_TX_FULL(uart) ((uart->FIFOSTS & UART_FIFOSTS_TXFULL_Msk)>>UART_FIFOSTS_TXFULL_Pos) /** * @brief Check RX FIFO is full or not * * @param[in] uart The base address of UART module * * @return * 1 = RX FIFO is full * 0 = RX FIFO is not full * \hideinitializer * */ #define UART_IS_RX_FULL(uart) ((uart->FIFOSTS & UART_FIFOSTS_RXFULL_Msk)>>UART_FIFOSTS_RXFULL_Pos) /** * @brief Get Tx full register value * * @param[in] uart The base address of UART module * * @return Tx full register value * \hideinitializer */ #define UART_GET_TX_FULL(uart) (uart->FIFOSTS & UART_FIFOSTS_TXFULL_Msk) /** * @brief Get Rx full register value * * @param[in] uart The base address of UART module * * @return Rx full register value * \hideinitializer */ #define UART_GET_RX_FULL(uart) (uart->FIFOSTS & UART_FIFOSTS_RXFULL_Msk) /** * @brief Enable specified interrupt * * @param[in] uart The base address of UART module * @param[in] u32eIntSel Interrupt type select * - \ref UART_INTEN_TOCNTEN_Msk : Rx Time Out interrupt * - \ref UART_INTEN_WKCTSIEN_Msk : Wakeup interrupt * - \ref UART_INTEN_BUFERRIEN_Msk : Buffer Error interrupt * - \ref UART_INTEN_RXTOIEN_Msk : Rx time-out interrupt * - \ref UART_INTEN_MODEMIEN_Msk : Modem interrupt * - \ref UART_INTEN_RLSIEN_Msk : Rx Line status interrupt * - \ref UART_INTEN_THREIEN_Msk : Tx empty interrupt * - \ref UART_INTEN_RDAIEN_Msk : Rx ready interrupt * * @return None * \hideinitializer */ #define UART_ENABLE_INT(uart, u32eIntSel) (uart->INTEN |= (u32eIntSel)) /** * @brief Disable specified interrupt * * @param[in] uart The base address of UART module * @param[in] u32eIntSel Interrupt type select * - \ref UART_INTEN_TOCNTEN_Msk : Rx Time Out interrupt * - \ref UART_INTEN_WKCTSIEN_Msk : Wakeup interrupt * - \ref UART_INTEN_BUFERRIEN_Msk : Buffer Error interrupt * - \ref UART_INTEN_RXTOIEN_Msk : Rx time-out interrupt * - \ref UART_INTEN_MODEMIEN_Msk : Modem interrupt * - \ref UART_INTEN_RLSIEN_Msk : Rx Line status interrupt * - \ref UART_INTEN_THREIEN_Msk : Tx empty interrupt * - \ref UART_INTEN_RDAIEN_Msk : Rx ready interrupt * @return None * \hideinitializer */ #define UART_DISABLE_INT(uart, u32eIntSel) (uart->INTEN &= ~ (u32eIntSel)) /** * @brief Get specified interrupt flag/status * * @param[in] uart The base address of UART module * @param[in] u32eIntTypeFlag Interrupt type select * - \ref UART_INTSTS_HWBUFEINT_Msk : In DMA Mode, Buffer Error Interrupt Indicator. * - \ref UART_INTSTS_HWTOINT_Msk : In DMA Mode, Time-out Interrupt Indicator. * - \ref UART_INTSTS_HWMODINT_Msk : In DMA Mode, MODEM Status Interrupt Indicator. * - \ref UART_INTSTS_HWRLSINT_Msk : In DMA Mode, Receive Line Status Interrupt Indicator. * - \ref UART_INTSTS_HWBUFEIF_Msk : In DMA Mode, Buffer Error Interrupt Flag. * - \ref UART_INTSTS_HWTOIF_Msk : In DMA Mode, Time-out Interrupt Flag. * - \ref UART_INTSTS_HWMODIF_Msk : In DMA Mode, MODEM Interrupt Flag. * - \ref UART_INTSTS_HWRLSIF_Msk : In DMA Mode, Receive Line Status Flag. * - \ref UART_INTSTS_LININT_Msk : LIN Bus Interrupt Indicator. * - \ref UART_INTSTS_BUFERRINT_Msk : Buffer Error Interrupt Indicator. * - \ref UART_INTSTS_RXTOINT_Msk : Time-out Interrupt Indicator. * - \ref UART_INTSTS_MODEMINT_Msk : Modem Status Interrupt Indicator. * - \ref UART_INTSTS_RLSINT_Msk : Receive Line Status Interrupt Indicator. * - \ref UART_INTSTS_THREINT_Msk : Transmit Holding Register Empty Interrupt Indicator. * - \ref UART_INTSTS_RDAINT_Msk : Receive Data Available Interrupt Indicator. * - \ref UART_INTSTS_LINIF_Msk : LIN Bus Flag. * - \ref UART_INTSTS_BUFERRIF_Msk : Buffer Error Interrupt Flag * - \ref UART_INTSTS_RXTOIF_Msk : Rx time-out interrupt Flag * - \ref UART_INTSTS_MODEMIF_Msk : Modem interrupt Flag * - \ref UART_INTSTS_RLSIF_Msk : Rx Line status interrupt Flag * - \ref UART_INTSTS_THREIF_Msk : Tx empty interrupt Flag * - \ref UART_INTSTS_RDAIF_Msk : Rx ready interrupt Flag * * @return * 0 = The specified interrupt is not happened. * 1 = The specified interrupt is happened. * \hideinitializer */ #define UART_GET_INT_FLAG(uart,u32eIntTypeFlag) ((uart->INTSTS & (u32eIntTypeFlag))?1:0) /** * @brief Set RTS pin is low * * @param[in] uart The base address of UART module * @return None */ __STATIC_INLINE void UART_CLEAR_RTS(UART_T* uart) { uart->MODEM |= UART_MODEM_RTSACTLV_Msk; uart->MODEM &= UART_MODEM_RTS_Msk; } /** * @brief Set RTS pin is high * * @param[in] uart The base address of UART module * @return None */ __STATIC_INLINE void UART_SET_RTS(UART_T* uart) { uart->MODEM |= UART_MODEM_RTSACTLV_Msk | UART_MODEM_RTS_Msk; } /** * @brief Clear RS-485 Address Byte Detection Flag * * @param[in] uart The base address of UART module * @return None * \hideinitializer */ #define UART_RS485_CLEAR_ADDR_FLAG(uart) (uart->FIFOSTS |= UART_FIFOSTS_ADDRDETF_Msk) /** * @brief Get RS-485 Address Byte Detection Flag * * @param[in] uart The base address of UART module * @return RS-485 Address Byte Detection Flag * \hideinitializer */ #define UART_RS485_GET_ADDR_FLAG(uart) ((uart->FIFOSTS & UART_FIFOSTS_ADDRDETF_Msk) >> UART_FIFOSTS_ADDRDETF_Pos) void UART_ClearIntFlag(UART_T* uart , uint32_t u32InterruptFlag); void UART_Close(UART_T* uart ); void UART_DisableFlowCtrl(UART_T* uart ); void UART_DisableInt(UART_T* uart, uint32_t u32InterruptFlag ); void UART_EnableFlowCtrl(UART_T* uart ); void UART_EnableInt(UART_T* uart, uint32_t u32InterruptFlag ); void UART_Open(UART_T* uart, uint32_t u32baudrate); uint32_t UART_Read(UART_T* uart, uint8_t *pu8RxBuf, uint32_t u32ReadBytes); void UART_SetLine_Config(UART_T* uart, uint32_t u32baudrate, uint32_t u32data_width, uint32_t u32parity, uint32_t u32stop_bits); void UART_SetTimeoutCnt(UART_T* uart, uint32_t u32TOC); void UART_SelectIrDAMode(UART_T* uart, uint32_t u32Buadrate, uint32_t u32Direction); void UART_SelectRS485Mode(UART_T* uart, uint32_t u32Mode, uint32_t u32Addr); uint32_t UART_Write(UART_T* uart,uint8_t *pu8TxBuf, uint32_t u32WriteBytes); /*@}*/ /* end of group NUC472_442_UART_EXPORTED_FUNCTIONS */ /*@}*/ /* end of group NUC472_442_UART_Driver */ /*@}*/ /* end of group NUC472_442_Device_Driver */ #ifdef __cplusplus } #endif #endif //__UART_H__ /*** (C) COPYRIGHT 2013 Nuvoton Technology Corp. ***/