Mouse code for the MacroRat
mbed-dev/targets/TARGET_NUVOTON/TARGET_M451/device/StdDriver/m451_i2c.c
- Committer:
- sahilmgandhi
- Date:
- 2017-06-03
- Revision:
- 46:b156ef445742
- Parent:
- 18:6a4db94011d3
File content as of revision 46:b156ef445742:
/**************************************************************************//** * @file i2c.c * @version V3.00 * $Revision: 23 $ * $Date: 15/08/11 10:26a $ * @brief M451 series I2C driver source file * * @note * Copyright (C) 2014~2015 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #include "M451Series.h" /** @addtogroup Standard_Driver Standard Driver @{ */ /** @addtogroup I2C_Driver I2C Driver @{ */ /** @addtogroup I2C_EXPORTED_FUNCTIONS I2C Exported Functions @{ */ /** * @brief Enable specify I2C Controller and set Clock Divider * * @param[in] i2c Specify I2C port * @param[in] u32BusClock The target I2C bus clock in Hz * * @return Actual I2C bus clock frequency * * @details The function enable the specify I2C Controller and set proper Clock Divider * in I2C CLOCK DIVIDED REGISTER (I2CLK) according to the target I2C Bus clock. * I2C Bus clock = PCLK / (4*(divider+1). * */ uint32_t I2C_Open(I2C_T *i2c, uint32_t u32BusClock) { uint32_t u32Div; u32Div = (uint32_t)(((SystemCoreClock * 10) / (u32BusClock * 4) + 5) / 10 - 1); /* Compute proper divider for I2C clock */ i2c->CLKDIV = u32Div; /* Enable I2C */ i2c->CTL |= I2C_CTL_I2CEN_Msk; return (SystemCoreClock / ((u32Div + 1) << 2)); } /** * @brief Disable specify I2C Controller * * @param[in] i2c Specify I2C port * * @return None * * @details Reset I2C Controller and disable specify I2C port. * */ void I2C_Close(I2C_T *i2c) { /* Reset I2C Controller */ if((uint32_t)i2c == I2C0_BASE) { SYS->IPRST1 |= SYS_IPRST1_I2C0RST_Msk; SYS->IPRST1 &= ~SYS_IPRST1_I2C0RST_Msk; } else if((uint32_t)i2c == I2C1_BASE) { SYS->IPRST1 |= SYS_IPRST1_I2C1RST_Msk; SYS->IPRST1 &= ~SYS_IPRST1_I2C1RST_Msk; } /* Disable I2C */ i2c->CTL &= ~I2C_CTL_I2CEN_Msk; } /** * @brief Clear Time-out Counter flag * * @param[in] i2c Specify I2C port * * @return None * * @details When Time-out flag will be set, use this function to clear I2C Bus Time-out counter flag . * */ void I2C_ClearTimeoutFlag(I2C_T *i2c) { i2c->TOCTL |= I2C_TOCTL_TOIF_Msk; } /** * @brief Set Control bit of I2C Controller * * @param[in] i2c Specify I2C port * @param[in] u8Start Set I2C START condition * @param[in] u8Stop Set I2C STOP condition * @param[in] u8Si Clear SI flag * @param[in] u8Ack Set I2C ACK bit * * @return None * * @details The function set I2C Control bit of I2C Bus protocol. * */ void I2C_Trigger(I2C_T *i2c, uint8_t u8Start, uint8_t u8Stop, uint8_t u8Si, uint8_t u8Ack) { uint32_t u32Reg = 0; if(u8Start) u32Reg |= I2C_CTL_STA; if(u8Stop) u32Reg |= I2C_CTL_STO; if(u8Si) u32Reg |= I2C_CTL_SI; if(u8Ack) u32Reg |= I2C_CTL_AA; i2c->CTL = (i2c->CTL & ~0x3C) | u32Reg; } /** * @brief Disable Interrupt of I2C Controller * * @param[in] i2c Specify I2C port * * @return None * * @details The function is used for disable I2C interrupt * */ void I2C_DisableInt(I2C_T *i2c) { i2c->CTL &= ~I2C_CTL_INTEN_Msk; } /** * @brief Enable Interrupt of I2C Controller * * @param[in] i2c Specify I2C port * * @return None * * @details The function is used for enable I2C interrupt * */ void I2C_EnableInt(I2C_T *i2c) { i2c->CTL |= I2C_CTL_INTEN_Msk; } /** * @brief Get I2C Bus Clock * * @param[in] i2c Specify I2C port * * @return The actual I2C Bus clock in Hz * * @details To get the actual I2C Bus Clock frequency. */ uint32_t I2C_GetBusClockFreq(I2C_T *i2c) { uint32_t u32Divider = i2c->CLKDIV; return (SystemCoreClock / ((u32Divider + 1) << 2)); } /** * @brief Set I2C Bus Clock * * @param[in] i2c Specify I2C port * @param[in] u32BusClock The target I2C Bus Clock in Hz * * @return The actual I2C Bus Clock in Hz * * @details To set the actual I2C Bus Clock frequency. */ uint32_t I2C_SetBusClockFreq(I2C_T *i2c, uint32_t u32BusClock) { uint32_t u32Div; u32Div = (uint32_t)(((SystemCoreClock * 10) / (u32BusClock * 4) + 5) / 10 - 1); /* Compute proper divider for I2C clock */ i2c->CLKDIV = u32Div; return (SystemCoreClock / ((u32Div + 1) << 2)); } /** * @brief Get Interrupt Flag * * @param[in] i2c Specify I2C port * * @return I2C interrupt flag status * * @details To get I2C Bus interrupt flag. */ uint32_t I2C_GetIntFlag(I2C_T *i2c) { return ((i2c->CTL & I2C_CTL_SI_Msk) == I2C_CTL_SI_Msk ? 1 : 0); } /** * @brief Get I2C Bus Status Code * * @param[in] i2c Specify I2C port * * @return I2C Status Code * * @details To get I2C Bus Status Code. */ uint32_t I2C_GetStatus(I2C_T *i2c) { return (i2c->STATUS); } /** * @brief Read a Byte from I2C Bus * * @param[in] i2c Specify I2C port * * @return I2C Data * * @details To read a bytes data from specify I2C port. */ uint8_t I2C_GetData(I2C_T *i2c) { return (i2c->DAT); } /** * @brief Send a byte to I2C Bus * * @param[in] i2c Specify I2C port * @param[in] u8Data The data to send to I2C bus * * @return None * * @details This function is used to write a byte to specified I2C port */ void I2C_SetData(I2C_T *i2c, uint8_t u8Data) { i2c->DAT = u8Data; } /** * @brief Set 7-bit Slave Address and GC Mode * * @param[in] i2c Specify I2C port * @param[in] u8SlaveNo Set the number of I2C address register (0~3) * @param[in] u8SlaveAddr 7-bit slave address * @param[in] u8GCMode Enable/Disable GC mode (I2C_GCMODE_ENABLE / I2C_GCMODE_DISABLE) * * @return None * * @details This function is used to set 7-bit slave addresses in I2C SLAVE ADDRESS REGISTER (I2CADDR0~3) * and enable GC Mode. * */ void I2C_SetSlaveAddr(I2C_T *i2c, uint8_t u8SlaveNo, uint8_t u8SlaveAddr, uint8_t u8GCMode) { switch(u8SlaveNo) { case 1: i2c->ADDR1 = (u8SlaveAddr << 1) | u8GCMode; break; case 2: i2c->ADDR2 = (u8SlaveAddr << 1) | u8GCMode; break; case 3: i2c->ADDR3 = (u8SlaveAddr << 1) | u8GCMode; break; case 0: default: i2c->ADDR0 = (u8SlaveAddr << 1) | u8GCMode; break; } } /** * @brief Configure the mask bits of 7-bit Slave Address * * @param[in] i2c Specify I2C port * @param[in] u8SlaveNo Set the number of I2C address mask register (0~3) * @param[in] u8SlaveAddrMask A byte for slave address mask * * @return None * * @details This function is used to set 7-bit slave addresses. * */ void I2C_SetSlaveAddrMask(I2C_T *i2c, uint8_t u8SlaveNo, uint8_t u8SlaveAddrMask) { switch(u8SlaveNo) { case 1: i2c->ADDRMSK1 = u8SlaveAddrMask << 1; break; case 2: i2c->ADDRMSK2 = u8SlaveAddrMask << 1; break; case 3: i2c->ADDRMSK3 = u8SlaveAddrMask << 1; break; case 0: default: i2c->ADDRMSK0 = u8SlaveAddrMask << 1; break; } } /** * @brief Enable Time-out Counter Function and support Long Time-out * * @param[in] i2c Specify I2C port * @param[in] u8LongTimeout Configure DIV4 to enable Long Time-out (0/1) * * @return None * * @details This function enable Time-out Counter function and configure DIV4 to support Long * Time-out. * */ void I2C_EnableTimeout(I2C_T *i2c, uint8_t u8LongTimeout) { if(u8LongTimeout) i2c->TOCTL |= I2C_TOCTL_TOCDIV4_Msk; else i2c->TOCTL &= ~I2C_TOCTL_TOCDIV4_Msk; i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk; } /** * @brief Disable Time-out Counter Function * * @param[in] i2c Specify I2C port * * @return None * * @details To disable Time-out Counter function in I2CTOC register. * */ void I2C_DisableTimeout(I2C_T *i2c) { i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk; } /** * @brief Enable I2C Wake-up Function * * @param[in] i2c Specify I2C port * * @return None * * @details To enable Wake-up function of I2C Wake-up control register. * */ void I2C_EnableWakeup(I2C_T *i2c) { i2c->WKCTL |= I2C_WKCTL_WKEN_Msk; } /** * @brief Disable I2C Wake-up Function * * @param[in] i2c Specify I2C port * * @return None * * @details To disable Wake-up function of I2C Wake-up control register. * */ void I2C_DisableWakeup(I2C_T *i2c) { i2c->WKCTL &= ~I2C_WKCTL_WKEN_Msk; } /** * @brief To get SMBus Status * * @param[in] i2c Specify I2C port * * @return SMBus status * * @details To get the Bus Management status of I2C_BUSSTS register * */ uint32_t I2C_SMBusGetStatus(I2C_T *i2c) { return (i2c->BUSSTS); } /** * @brief Clear SMBus Interrupt Flag * * @param[in] i2c Specify I2C port * @param[in] u8SMBusIntFlag Specify SMBus interrupt flag * * @return None * * @details To clear flags of I2C_BUSSTS status register if interrupt set. * */ void I2C_SMBusClearInterruptFlag(I2C_T *i2c, uint8_t u8SMBusIntFlag) { i2c->BUSSTS |= u8SMBusIntFlag; } /** * @brief Set SMBus Bytes Counts of Transmission or Reception * * @param[in] i2c Specify I2C port * @param[in] u32PktSize Transmit / Receive bytes * * @return None * * @details The transmission or receive byte number in one transaction when PECEN is set. The maximum is 255 bytes. * */ void I2C_SMBusSetPacketByteCount(I2C_T *i2c, uint32_t u32PktSize) { i2c->PKTSIZE = u32PktSize; } /** * @brief Init SMBus Host/Device Mode * * @param[in] i2c Specify I2C port * @param[in] u8HostDevice Init SMBus port mode(I2C_SMBH_ENABLE(1)/I2C_SMBD_ENABLE(0)) * * @return None * * @details Using SMBus communication must specify the port is a Host or a Device. * */ void I2C_SMBusOpen(I2C_T *i2c, uint8_t u8HostDevice) { /* Clear BMHEN, BMDEN of BUSCTL Register */ i2c->BUSCTL &= ~(I2C_BUSCTL_BMHEN_Msk | I2C_BUSCTL_BMDEN_Msk); /* Set SMBus Host/Device Mode, and enable Bus Management*/ if(u8HostDevice == I2C_SMBH_ENABLE) i2c->BUSCTL |= (I2C_BUSCTL_BMHEN_Msk | I2C_BUSCTL_BUSEN_Msk); else i2c->BUSCTL |= (I2C_BUSCTL_BMDEN_Msk | I2C_BUSCTL_BUSEN_Msk); } /** * @brief Disable SMBus function * * @param[in] i2c Specify I2C port * * @return None * * @details Disable all SMBus function include Bus disable, CRC check, Acknowledge by manual, Host/Device Mode. * */ void I2C_SMBusClose(I2C_T *i2c) { i2c->BUSCTL = 0x00; } /** * @brief Enable SMBus PEC Transmit Function * * @param[in] i2c Specify I2C port * @param[in] u8PECTxEn CRC transmit enable(PECTX_ENABLE) or disable(PECTX_DISABLE) * * @return None * * @details When enable CRC check function, the Host or Device needs to transmit CRC byte. * */ void I2C_SMBusPECTxEnable(I2C_T *i2c, uint8_t u8PECTxEn) { i2c->BUSCTL &= ~I2C_BUSCTL_PECTXEN_Msk; if(u8PECTxEn) i2c->BUSCTL |= (I2C_BUSCTL_PECEN_Msk | I2C_BUSCTL_PECTXEN_Msk); else i2c->BUSCTL |= I2C_BUSCTL_PECEN_Msk; } /** * @brief Get SMBus CRC value * * @param[in] i2c Specify I2C port * * @return A byte is packet error check value * * @details The CRC check value after a transmission or a reception by count by using CRC8 * */ uint8_t I2C_SMBusGetPECValue(I2C_T *i2c) { return i2c->PKTCRC; } /** * @brief Calculate Time-out of SMBus idle period * * @param[in] i2c Specify I2C port * @param[in] us Time-out length(us) * @param[in] u32Hclk I2C peripheral clock frequency * * @return None * * @details This function is used to set SMBus Time-out length when bus is in Idle state. * */ void I2C_SMBusIdleTimeout(I2C_T *i2c, uint32_t us, uint32_t u32Hclk) { uint32_t u32Div, u32Hclk_kHz; i2c->BUSCTL |= I2C_BUSCTL_TIDLE_Msk; u32Hclk_kHz = u32Hclk / 1000; u32Div = (((us * u32Hclk_kHz) / 1000) >> 2) - 1; if(u32Div > 255) { i2c->BUSTOUT = 0xFF; } else { i2c->BUSTOUT = u32Div; } } /** * @brief Calculate Time-out of SMBus active period * * @param[in] i2c Specify I2C port * @param[in] ms Time-out length(ms) * @param[in] u32Pclk peripheral clock frequency * * @return None * * @details This function is used to set SMBus Time-out length when bus is in active state. * Time-out length is calculate the SCL line "one clock" pull low timing. * */ void I2C_SMBusTimeout(I2C_T *i2c, uint32_t ms, uint32_t u32Pclk) { uint32_t u32Div, u32Pclk_kHz; i2c->BUSCTL &= ~I2C_BUSCTL_TIDLE_Msk; /* DIV4 disabled */ i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk; u32Pclk_kHz = u32Pclk / 1000; u32Div = ((ms * u32Pclk_kHz) / (16 * 1024)) - 1; if(u32Div <= 0xFF) { i2c->BUSTOUT = u32Div; return; } /* DIV4 enabled */ i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk; i2c->BUSTOUT = (((ms * u32Pclk_kHz) / (16 * 1024 * 4)) - 1) & 0xFF; //The max value is 255 } /** * @brief Calculate Cumulative Clock low Time-out of SMBus active period * * @param[in] i2c Specify I2C port * @param[in] ms Time-out length(ms) * @param[in] u32Pclk peripheral clock frequency * * @return None * * @details This function is used to set SMBus Time-out length when bus is in Active state. * Time-out length is calculate the SCL line "clocks" low cumulative timing. * */ void I2C_SMBusClockLoTimeout(I2C_T *i2c, uint32_t ms, uint32_t u32Pclk) { uint32_t u32Div, u32Pclk_kHz; i2c->BUSCTL &= ~I2C_BUSCTL_TIDLE_Msk; /* DIV4 disabled */ i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk; u32Pclk_kHz = u32Pclk / 1000; u32Div = ((ms * u32Pclk_kHz) / (16 * 1024)) - 1; if(u32Div <= 0xFF) { i2c->CLKTOUT = u32Div; return; } /* DIV4 enabled */ i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk; i2c->CLKTOUT = (((ms * u32Pclk_kHz) / (16 * 1024 * 4)) - 1) & 0xFF; //The max value is 255 } /*@}*/ /* end of group I2C_EXPORTED_FUNCTIONS */ /*@}*/ /* end of group I2C_Driver */ /*@}*/ /* end of group Standard_Driver */ /*** (C) COPYRIGHT 2014~2015 Nuvoton Technology Corp. ***/