Mouse code for the MacroRat
Diff: mbed-dev/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_hal_usart.h
- Revision:
- 18:6a4db94011d3
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_hal_usart.h Sun May 14 23:18:57 2017 +0000 @@ -0,0 +1,588 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_usart.h + * @author MCD Application Team + * @version V1.5.0 + * @date 06-May-2016 + * @brief Header file of USART HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_USART_H +#define __STM32F4xx_HAL_USART_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal_def.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @addtogroup USART + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup USART_Exported_Types USART Exported Types + * @{ + */ + +/** + * @brief USART Init Structure definition + */ +typedef struct +{ + uint32_t BaudRate; /*!< This member configures the Usart communication baud rate. + The baud rate is computed using the following formula: + - IntegerDivider = ((PCLKx) / (8 * (husart->Init.BaudRate))) + - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 8) + 0.5 */ + + uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame. + This parameter can be a value of @ref USART_Word_Length */ + + uint32_t StopBits; /*!< Specifies the number of stop bits transmitted. + This parameter can be a value of @ref USART_Stop_Bits */ + + uint32_t Parity; /*!< Specifies the parity mode. + This parameter can be a value of @ref USART_Parity + @note When parity is enabled, the computed parity is inserted + at the MSB position of the transmitted data (9th bit when + the word length is set to 9 data bits; 8th bit when the + word length is set to 8 data bits). */ + + uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled. + This parameter can be a value of @ref USART_Mode */ + + uint32_t CLKPolarity; /*!< Specifies the steady state of the serial clock. + This parameter can be a value of @ref USART_Clock_Polarity */ + + uint32_t CLKPhase; /*!< Specifies the clock transition on which the bit capture is made. + This parameter can be a value of @ref USART_Clock_Phase */ + + uint32_t CLKLastBit; /*!< Specifies whether the clock pulse corresponding to the last transmitted + data bit (MSB) has to be output on the SCLK pin in synchronous mode. + This parameter can be a value of @ref USART_Last_Bit */ +}USART_InitTypeDef; + +/** + * @brief HAL State structures definition + */ +typedef enum +{ + HAL_USART_STATE_RESET = 0x00U, /*!< Peripheral is not yet Initialized */ + HAL_USART_STATE_READY = 0x01U, /*!< Peripheral Initialized and ready for use */ + HAL_USART_STATE_BUSY = 0x02U, /*!< an internal process is ongoing */ + HAL_USART_STATE_BUSY_TX = 0x12U, /*!< Data Transmission process is ongoing */ + HAL_USART_STATE_BUSY_RX = 0x22U, /*!< Data Reception process is ongoing */ + HAL_USART_STATE_BUSY_TX_RX = 0x32U, /*!< Data Transmission Reception process is ongoing */ + HAL_USART_STATE_TIMEOUT = 0x03U, /*!< Timeout state */ + HAL_USART_STATE_ERROR = 0x04U /*!< Error */ +}HAL_USART_StateTypeDef; + +/** + * @brief USART handle Structure definition + */ +typedef struct +{ + USART_TypeDef *Instance; /* USART registers base address */ + + USART_InitTypeDef Init; /* Usart communication parameters */ + + uint8_t *pTxBuffPtr; /* Pointer to Usart Tx transfer Buffer */ + + uint16_t TxXferSize; /* Usart Tx Transfer size */ + + __IO uint16_t TxXferCount; /* Usart Tx Transfer Counter */ + + uint8_t *pRxBuffPtr; /* Pointer to Usart Rx transfer Buffer */ + + uint16_t RxXferSize; /* Usart Rx Transfer size */ + + __IO uint16_t RxXferCount; /* Usart Rx Transfer Counter */ + + DMA_HandleTypeDef *hdmatx; /* Usart Tx DMA Handle parameters */ + + DMA_HandleTypeDef *hdmarx; /* Usart Rx DMA Handle parameters */ + + HAL_LockTypeDef Lock; /* Locking object */ + + __IO HAL_USART_StateTypeDef State; /* Usart communication state */ + + __IO uint32_t ErrorCode; /* USART Error code */ + +}USART_HandleTypeDef; +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup USART_Exported_Constants USART Exported Constants + * @{ + */ + +/** @defgroup USART_Error_Code USART Error Code + * @brief USART Error Code + * @{ + */ +#define HAL_USART_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */ +#define HAL_USART_ERROR_PE ((uint32_t)0x00000001U) /*!< Parity error */ +#define HAL_USART_ERROR_NE ((uint32_t)0x00000002U) /*!< Noise error */ +#define HAL_USART_ERROR_FE ((uint32_t)0x00000004U) /*!< Frame error */ +#define HAL_USART_ERROR_ORE ((uint32_t)0x00000008U) /*!< Overrun error */ +#define HAL_USART_ERROR_DMA ((uint32_t)0x00000010U) /*!< DMA transfer error */ +/** + * @} + */ + +/** @defgroup USART_Word_Length USART Word Length + * @{ + */ +#define USART_WORDLENGTH_8B ((uint32_t)0x00000000U) +#define USART_WORDLENGTH_9B ((uint32_t)USART_CR1_M) +/** + * @} + */ + +/** @defgroup USART_Stop_Bits USART Number of Stop Bits + * @{ + */ +#define USART_STOPBITS_1 ((uint32_t)0x00000000U) +#define USART_STOPBITS_0_5 ((uint32_t)USART_CR2_STOP_0) +#define USART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1) +#define USART_STOPBITS_1_5 ((uint32_t)(USART_CR2_STOP_0 | USART_CR2_STOP_1)) +/** + * @} + */ + +/** @defgroup USART_Parity USART Parity + * @{ + */ +#define USART_PARITY_NONE ((uint32_t)0x00000000U) +#define USART_PARITY_EVEN ((uint32_t)USART_CR1_PCE) +#define USART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) +/** + * @} + */ + +/** @defgroup USART_Mode USART Mode + * @{ + */ +#define USART_MODE_RX ((uint32_t)USART_CR1_RE) +#define USART_MODE_TX ((uint32_t)USART_CR1_TE) +#define USART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE)) +/** + * @} + */ + +/** @defgroup USART_Clock USART Clock + * @{ + */ +#define USART_CLOCK_DISABLE ((uint32_t)0x00000000U) +#define USART_CLOCK_ENABLE ((uint32_t)USART_CR2_CLKEN) +/** + * @} + */ + +/** @defgroup USART_Clock_Polarity USART Clock Polarity + * @{ + */ +#define USART_POLARITY_LOW ((uint32_t)0x00000000U) +#define USART_POLARITY_HIGH ((uint32_t)USART_CR2_CPOL) +/** + * @} + */ + +/** @defgroup USART_Clock_Phase USART Clock Phase + * @{ + */ +#define USART_PHASE_1EDGE ((uint32_t)0x00000000U) +#define USART_PHASE_2EDGE ((uint32_t)USART_CR2_CPHA) +/** + * @} + */ + +/** @defgroup USART_Last_Bit USART Last Bit + * @{ + */ +#define USART_LASTBIT_DISABLE ((uint32_t)0x00000000U) +#define USART_LASTBIT_ENABLE ((uint32_t)USART_CR2_LBCL) +/** + * @} + */ + +/** @defgroup USART_NACK_State USART NACK State + * @{ + */ +#define USART_NACK_ENABLE ((uint32_t)USART_CR3_NACK) +#define USART_NACK_DISABLE ((uint32_t)0x00000000U) +/** + * @} + */ + +/** @defgroup USART_Flags USART Flags + * Elements values convention: 0xXXXX + * - 0xXXXX : Flag mask in the SR register + * @{ + */ +#define USART_FLAG_TXE ((uint32_t)0x00000080U) +#define USART_FLAG_TC ((uint32_t)0x00000040U) +#define USART_FLAG_RXNE ((uint32_t)0x00000020U) +#define USART_FLAG_IDLE ((uint32_t)0x00000010U) +#define USART_FLAG_ORE ((uint32_t)0x00000008U) +#define USART_FLAG_NE ((uint32_t)0x00000004U) +#define USART_FLAG_FE ((uint32_t)0x00000002U) +#define USART_FLAG_PE ((uint32_t)0x00000001U) +/** + * @} + */ + +/** @defgroup USART_Interrupt_definition USART Interrupts Definition + * Elements values convention: 0xY000XXXX + * - XXXX : Interrupt mask in the XX register + * - Y : Interrupt source register (2bits) + * - 01: CR1 register + * - 10: CR2 register + * - 11: CR3 register + * + * @{ + */ +#define USART_IT_PE ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_PEIE)) +#define USART_IT_TXE ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_TXEIE)) +#define USART_IT_TC ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_TCIE)) +#define USART_IT_RXNE ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_RXNEIE)) +#define USART_IT_IDLE ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_IDLEIE)) + +#define USART_IT_LBD ((uint32_t)(USART_CR2_REG_INDEX << 28U | USART_CR2_LBDIE)) + +#define USART_IT_CTS ((uint32_t)(USART_CR3_REG_INDEX << 28U | USART_CR3_CTSIE)) +#define USART_IT_ERR ((uint32_t)(USART_CR3_REG_INDEX << 28U | USART_CR3_EIE)) +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup USART_Exported_Macros USART Exported Macros + * @{ + */ + +/** @brief Reset USART handle state + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @retval None + */ +#define __HAL_USART_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_USART_STATE_RESET) + +/** @brief Checks whether the specified Smartcard flag is set or not. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg USART_FLAG_TXE: Transmit data register empty flag + * @arg USART_FLAG_TC: Transmission Complete flag + * @arg USART_FLAG_RXNE: Receive data register not empty flag + * @arg USART_FLAG_IDLE: Idle Line detection flag + * @arg USART_FLAG_ORE: Overrun Error flag + * @arg USART_FLAG_NE: Noise Error flag + * @arg USART_FLAG_FE: Framing Error flag + * @arg USART_FLAG_PE: Parity Error flag + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_USART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__)) + +/** @brief Clears the specified Smartcard pending flags. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @param __FLAG__: specifies the flag to check. + * This parameter can be any combination of the following values: + * @arg USART_FLAG_TC: Transmission Complete flag. + * @arg USART_FLAG_RXNE: Receive data register not empty flag. + * + * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (Overrun + * error) and IDLE (Idle line detected) flags are cleared by software + * sequence: a read operation to USART_SR register followed by a read + * operation to USART_DR register. + * @note RXNE flag can be also cleared by a read to the USART_DR register. + * @note TC flag can be also cleared by software sequence: a read operation to + * USART_SR register followed by a write operation to USART_DR register. + * @note TXE flag is cleared only by a write to the USART_DR register. + * + * @retval None + */ +#define __HAL_USART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__)) + +/** @brief Clear the USART PE pending flag. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @retval None + */ +#define __HAL_USART_CLEAR_PEFLAG(__HANDLE__) \ + do{ \ + __IO uint32_t tmpreg = 0x00U; \ + tmpreg = (__HANDLE__)->Instance->SR; \ + tmpreg = (__HANDLE__)->Instance->DR; \ + UNUSED(tmpreg); \ + } while(0) + +/** @brief Clear the USART FE pending flag. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @retval None + */ +#define __HAL_USART_CLEAR_FEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clear the USART NE pending flag. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @retval None + */ +#define __HAL_USART_CLEAR_NEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clear the UART ORE pending flag. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @retval None + */ +#define __HAL_USART_CLEAR_OREFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clear the USART IDLE pending flag. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @retval None + */ +#define __HAL_USART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Enables or disables the specified USART interrupts. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @param __INTERRUPT__: specifies the USART interrupt source to check. + * This parameter can be one of the following values: + * @arg USART_IT_TXE: Transmit Data Register empty interrupt + * @arg USART_IT_TC: Transmission complete interrupt + * @arg USART_IT_RXNE: Receive Data register not empty interrupt + * @arg USART_IT_IDLE: Idle line detection interrupt + * @arg USART_IT_PE: Parity Error interrupt + * @arg USART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +#define __HAL_USART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28U) == 1U)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & USART_IT_MASK)): \ + (((__INTERRUPT__) >> 28U) == 2U)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & USART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & USART_IT_MASK))) +#define __HAL_USART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28U) == 1U)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & USART_IT_MASK)): \ + (((__INTERRUPT__) >> 28U) == 2U)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & USART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & USART_IT_MASK))) + +/** @brief Checks whether the specified USART interrupt has occurred or not. + * @param __HANDLE__: specifies the USART Handle. + * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral. + * @param __IT__: specifies the USART interrupt source to check. + * This parameter can be one of the following values: + * @arg USART_IT_TXE: Transmit Data Register empty interrupt + * @arg USART_IT_TC: Transmission complete interrupt + * @arg USART_IT_RXNE: Receive Data register not empty interrupt + * @arg USART_IT_IDLE: Idle line detection interrupt + * @arg USART_IT_ERR: Error interrupt + * @arg USART_IT_PE: Parity Error interrupt + * @retval The new state of __IT__ (TRUE or FALSE). + */ +#define __HAL_USART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28U) == 1U)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28U) == 2U)? \ + (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & USART_IT_MASK)) + +/** @brief Macro to enable the USART's one bit sample method + * @param __HANDLE__: specifies the USART Handle. + * @retval None + */ +#define __HAL_USART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT) + +/** @brief Macro to disable the USART's one bit sample method + * @param __HANDLE__: specifies the USART Handle. + * @retval None + */ +#define __HAL_USART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT)) + +/** @brief Enable USART + * @param __HANDLE__: specifies the USART Handle. + * USART Handle selects the USARTx peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_USART_ENABLE(__HANDLE__) ( (__HANDLE__)->Instance->CR1 |= USART_CR1_UE) + +/** @brief Disable USART + * @param __HANDLE__: specifies the USART Handle. + * USART Handle selects the USARTx peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_USART_DISABLE(__HANDLE__) ( (__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE) + +/** + * @} + */ +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup USART_Exported_Functions + * @{ + */ + +/** @addtogroup USART_Exported_Functions_Group1 + * @{ + */ +/* Initialization/de-initialization functions **********************************/ +HAL_StatusTypeDef HAL_USART_Init(USART_HandleTypeDef *husart); +HAL_StatusTypeDef HAL_USART_DeInit(USART_HandleTypeDef *husart); +void HAL_USART_MspInit(USART_HandleTypeDef *husart); +void HAL_USART_MspDeInit(USART_HandleTypeDef *husart); +/** + * @} + */ + +/** @addtogroup USART_Exported_Functions_Group2 + * @{ + */ +/* IO operation functions *******************************************************/ +HAL_StatusTypeDef HAL_USART_Transmit(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_USART_Receive(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_USART_TransmitReceive(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_USART_Transmit_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size); +HAL_StatusTypeDef HAL_USART_Receive_IT(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size); +HAL_StatusTypeDef HAL_USART_TransmitReceive_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size); +HAL_StatusTypeDef HAL_USART_Transmit_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size); +HAL_StatusTypeDef HAL_USART_Receive_DMA(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size); +HAL_StatusTypeDef HAL_USART_TransmitReceive_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size); +HAL_StatusTypeDef HAL_USART_DMAPause(USART_HandleTypeDef *husart); +HAL_StatusTypeDef HAL_USART_DMAResume(USART_HandleTypeDef *husart); +HAL_StatusTypeDef HAL_USART_DMAStop(USART_HandleTypeDef *husart); + +void HAL_USART_IRQHandler(USART_HandleTypeDef *husart); +void HAL_USART_TxCpltCallback(USART_HandleTypeDef *husart); +void HAL_USART_TxHalfCpltCallback(USART_HandleTypeDef *husart); +void HAL_USART_RxCpltCallback(USART_HandleTypeDef *husart); +void HAL_USART_RxHalfCpltCallback(USART_HandleTypeDef *husart); +void HAL_USART_TxRxCpltCallback(USART_HandleTypeDef *husart); +void HAL_USART_ErrorCallback(USART_HandleTypeDef *husart); +/** + * @} + */ + +/** @addtogroup USART_Exported_Functions_Group3 + * @{ + */ +/* Peripheral State functions ************************************************/ +HAL_USART_StateTypeDef HAL_USART_GetState(USART_HandleTypeDef *husart); +uint32_t HAL_USART_GetError(USART_HandleTypeDef *husart); +/** + * @} + */ + +/** + * @} + */ +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private constants ---------------------------------------------------------*/ +/** @defgroup USART_Private_Constants USART Private Constants + * @{ + */ +/** @brief USART interruptions flag mask + * + */ +#define USART_IT_MASK ((uint32_t) USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE | USART_CR1_RXNEIE | \ + USART_CR1_IDLEIE | USART_CR2_LBDIE | USART_CR3_CTSIE | USART_CR3_EIE ) + +#define USART_CR1_REG_INDEX 1U +#define USART_CR2_REG_INDEX 2U +#define USART_CR3_REG_INDEX 3U +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup USART_Private_Macros USART Private Macros + * @{ + */ +#define IS_USART_NACK_STATE(NACK) (((NACK) == USART_NACK_ENABLE) || \ + ((NACK) == USART_NACK_DISABLE)) +#define IS_USART_LASTBIT(LASTBIT) (((LASTBIT) == USART_LASTBIT_DISABLE) || \ + ((LASTBIT) == USART_LASTBIT_ENABLE)) +#define IS_USART_PHASE(CPHA) (((CPHA) == USART_PHASE_1EDGE) || ((CPHA) == USART_PHASE_2EDGE)) +#define IS_USART_POLARITY(CPOL) (((CPOL) == USART_POLARITY_LOW) || ((CPOL) == USART_POLARITY_HIGH)) +#define IS_USART_CLOCK(CLOCK) (((CLOCK) == USART_CLOCK_DISABLE) || \ + ((CLOCK) == USART_CLOCK_ENABLE)) +#define IS_USART_WORD_LENGTH(LENGTH) (((LENGTH) == USART_WORDLENGTH_8B) || \ + ((LENGTH) == USART_WORDLENGTH_9B)) +#define IS_USART_STOPBITS(STOPBITS) (((STOPBITS) == USART_STOPBITS_1) || \ + ((STOPBITS) == USART_STOPBITS_0_5) || \ + ((STOPBITS) == USART_STOPBITS_1_5) || \ + ((STOPBITS) == USART_STOPBITS_2)) +#define IS_USART_PARITY(PARITY) (((PARITY) == USART_PARITY_NONE) || \ + ((PARITY) == USART_PARITY_EVEN) || \ + ((PARITY) == USART_PARITY_ODD)) +#define IS_USART_MODE(MODE) ((((MODE) & (uint32_t)0xFFF3) == 0x00U) && ((MODE) != (uint32_t)0x00U)) +#define IS_USART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 10500001U) + +#define USART_DIV(_PCLK_, _BAUD_) (((_PCLK_)*25U)/(2U*(_BAUD_))) +#define USART_DIVMANT(_PCLK_, _BAUD_) (USART_DIV((_PCLK_), (_BAUD_))/100U) +#define USART_DIVFRAQ(_PCLK_, _BAUD_) (((USART_DIV((_PCLK_), (_BAUD_)) - (USART_DIVMANT((_PCLK_), (_BAUD_)) * 100U)) * 16U + 50U) / 100U) +#define USART_BRR(_PCLK_, _BAUD_) ((USART_DIVMANT((_PCLK_), (_BAUD_)) << 4U)|(USART_DIVFRAQ((_PCLK_), (_BAUD_)) & 0x0FU)) +/** + * @} + */ + +/* Private functions ---------------------------------------------------------*/ +/** @defgroup USART_Private_Functions USART Private Functions + * @{ + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_USART_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/