Mouse code for the MacroRat
Diff: mbed-dev/targets/TARGET_STM/TARGET_STM32F2/device/stm32f2xx_hal_uart.c
- Revision:
- 18:6a4db94011d3
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev/targets/TARGET_STM/TARGET_STM32F2/device/stm32f2xx_hal_uart.c Sun May 14 23:18:57 2017 +0000 @@ -0,0 +1,1954 @@ +/** + ****************************************************************************** + * @file stm32f2xx_hal_uart.c + * @author MCD Application Team + * @version V1.1.3 + * @date 29-June-2016 + * @brief UART HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Universal Asynchronous Receiver Transmitter (UART) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral Control functions + * + Peripheral State and Errors functions + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The UART HAL driver can be used as follows: + + (#) Declare a UART_HandleTypeDef handle structure. + + (#) Initialize the UART low level resources by implementing the HAL_UART_MspInit() API: + (##) Enable the USARTx interface clock. + (##) UART pins configuration: + (+++) Enable the clock for the UART GPIOs. + (+++) Configure these UART pins as alternate function pull-up. + (##) NVIC configuration if you need to use interrupt process (HAL_UART_Transmit_IT() + and HAL_UART_Receive_IT() APIs): + (+++) Configure the USARTx interrupt priority. + (+++) Enable the NVIC USART IRQ handle. + (##) DMA Configuration if you need to use DMA process (HAL_UART_Transmit_DMA() + and HAL_UART_Receive_DMA() APIs): + (+++) Declare a DMA handle structure for the Tx/Rx stream. + (+++) Enable the DMAx interface clock. + (+++) Configure the declared DMA handle structure with the required + Tx/Rx parameters. + (+++) Configure the DMA Tx/Rx Stream. + (+++) Associate the initialized DMA handle to the UART DMA Tx/Rx handle. + (+++) Configure the priority and enable the NVIC for the transfer complete + interrupt on the DMA Tx/Rx Stream. + + (#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware + flow control and Mode(Receiver/Transmitter) in the Init structure. + + (#) For the UART asynchronous mode, initialize the UART registers by calling + the HAL_UART_Init() API. + + (#) For the UART Half duplex mode, initialize the UART registers by calling + the HAL_HalfDuplex_Init() API. + + (#) For the LIN mode, initialize the UART registers by calling the HAL_LIN_Init() API. + + (#) For the Multi-Processor mode, initialize the UART registers by calling + the HAL_MultiProcessor_Init() API. + + [..] + (@) The specific UART interrupts (Transmission complete interrupt, + RXNE interrupt and Error Interrupts) will be managed using the macros + __HAL_UART_ENABLE_IT() and __HAL_UART_DISABLE_IT() inside the transmit + and receive process. + + [..] + (@) These APIs (HAL_UART_Init() and HAL_HalfDuplex_Init()) configure also the + low level Hardware GPIO, CLOCK, CORTEX...etc) by calling the customized + HAL_UART_MspInit() API. + + [..] + Three operation modes are available within this driver : + + *** Polling mode IO operation *** + ================================= + [..] + (+) Send an amount of data in blocking mode using HAL_UART_Transmit() + (+) Receive an amount of data in blocking mode using HAL_UART_Receive() + + *** Interrupt mode IO operation *** + =================================== + [..] + (+) Send an amount of data in non blocking mode using HAL_UART_Transmit_IT() + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode using HAL_UART_Receive_IT() + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + + *** DMA mode IO operation *** + ============================== + [..] + (+) Send an amount of data in non blocking mode (DMA) using HAL_UART_Transmit_DMA() + (+) At transmission end of half transfer HAL_UART_TxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxHalfCpltCallback + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode (DMA) using HAL_UART_Receive_DMA() + (+) At reception end of half transfer HAL_UART_RxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxHalfCpltCallback + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + (+) Pause the DMA Transfer using HAL_UART_DMAPause() + (+) Resume the DMA Transfer using HAL_UART_DMAResume() + (+) Stop the DMA Transfer using HAL_UART_DMAStop() + + *** UART HAL driver macros list *** + ============================================= + [..] + Below the list of most used macros in UART HAL driver. + + (+) __HAL_UART_ENABLE: Enable the UART peripheral + (+) __HAL_UART_DISABLE: Disable the UART peripheral + (+) __HAL_UART_GET_FLAG : Check whether the specified UART flag is set or not + (+) __HAL_UART_CLEAR_FLAG : Clear the specified UART pending flag + (+) __HAL_UART_ENABLE_IT: Enable the specified UART interrupt + (+) __HAL_UART_DISABLE_IT: Disable the specified UART interrupt + (+) __HAL_UART_GET_IT_SOURCE: Check whether the specified UART interrupt has occurred or not + + [..] + (@) You can refer to the UART HAL driver header file for more useful macros + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f2xx_hal.h" + +/** @addtogroup STM32F2xx_HAL_Driver + * @{ + */ + +/** @defgroup UART UART + * @brief HAL UART module driver + * @{ + */ +#ifdef HAL_UART_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @addtogroup UART_Private_Constants + * @{ + */ +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/** @addtogroup UART_Private_Functions UART Private Functions + * @{ + */ +static void UART_EndTxTransfer(UART_HandleTypeDef *huart); +static void UART_EndRxTransfer(UART_HandleTypeDef *huart); +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma); +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAError(DMA_HandleTypeDef *hdma); +static void UART_DMAAbortOnError(DMA_HandleTypeDef *hdma); +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout); +static void UART_SetConfig (UART_HandleTypeDef *huart); +/** + * @} + */ + +/* Exported functions ---------------------------------------------------------*/ +/** @defgroup UART_Exported_Functions UART Exported Functions + * @{ + */ + +/** @defgroup UART_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim +=============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to initialize the USARTx or the UARTy + in asynchronous mode. + (+) For the asynchronous mode only these parameters can be configured: + (++) Baud Rate + (++) Word Length + (++) Stop Bit + (++) Parity: If the parity is enabled, then the MSB bit of the data written + in the data register is transmitted but is changed by the parity bit. + Depending on the frame length defined by the M bit (8-bits or 9-bits), + please refer to Reference manual for possible UART frame formats. + (++) Hardware flow control + (++) Receiver/transmitter modes + (++) Over Sampling Method + [..] + The HAL_UART_Init(), HAL_HalfDuplex_Init(), HAL_LIN_Init() and HAL_MultiProcessor_Init() APIs + follow respectively the UART asynchronous, UART Half duplex, LIN and Multi-Processor + configuration procedures (details for the procedures are available in reference manual (RM0329)). + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the UART mode according to the specified parameters in + * the UART_InitTypeDef and create the associated handle. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + if(huart->Init.HwFlowCtl != UART_HWCONTROL_NONE) + { + /* The hardware flow control is available only for USART1, USART2, USART3 and USART6 */ + assert_param(IS_UART_HWFLOW_INSTANCE(huart->Instance)); + assert_param(IS_UART_HARDWARE_FLOW_CONTROL(huart->Init.HwFlowCtl)); + } + else + { + assert_param(IS_UART_INSTANCE(huart->Instance)); + } + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In asynchronous mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN)); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState= HAL_UART_STATE_READY; + huart->RxState= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the half-duplex mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In half-duplex mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_IREN | USART_CR3_SCEN)); + + /* Enable the Half-Duplex mode by setting the HDSEL bit in the CR3 register */ + SET_BIT(huart->Instance->CR3, USART_CR3_HDSEL); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state*/ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState= HAL_UART_STATE_READY; + huart->RxState= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the LIN mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param BreakDetectLength: Specifies the LIN break detection length. + * This parameter can be one of the following values: + * @arg UART_LINBREAKDETECTLENGTH_10B: 10-bit break detection + * @arg UART_LINBREAKDETECTLENGTH_11B: 11-bit break detection + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + assert_param(IS_UART_LIN_BREAK_DETECT_LENGTH(BreakDetectLength)); + assert_param(IS_UART_LIN_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_LIN_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In LIN mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, USART_CR2_CLKEN); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_HDSEL | USART_CR3_IREN | USART_CR3_SCEN)); + + /* Enable the LIN mode by setting the LINEN bit in the CR2 register */ + SET_BIT(huart->Instance->CR2, USART_CR2_LINEN); + + /* Set the USART LIN Break detection length. */ + CLEAR_BIT(huart->Instance->CR2, USART_CR2_LBDL); + SET_BIT(huart->Instance->CR2, BreakDetectLength); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state*/ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState= HAL_UART_STATE_READY; + huart->RxState= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the Multi-Processor mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param Address: USART address + * @param WakeUpMethod: specifies the USART wake-up method. + * This parameter can be one of the following values: + * @arg UART_WAKEUPMETHOD_IDLELINE: Wake-up by an idle line detection + * @arg UART_WAKEUPMETHOD_ADDRESSMARK: Wake-up by an address mark + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + assert_param(IS_UART_WAKEUPMETHOD(WakeUpMethod)); + assert_param(IS_UART_ADDRESS(Address)); + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In Multi-Processor mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register */ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN)); + + /* Clear the USART address */ + CLEAR_BIT(huart->Instance->CR2, USART_CR2_ADD); + /* Set the USART address node */ + SET_BIT(huart->Instance->CR2, Address); + + /* Set the wake up method by setting the WAKE bit in the CR1 register */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_WAKE); + SET_BIT(huart->Instance->CR1, WakeUpMethod); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState= HAL_UART_STATE_READY; + huart->RxState= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief DeInitializes the UART peripheral. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DeInit(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + huart->gState = HAL_UART_STATE_BUSY; + + /* DeInit the low level hardware */ + HAL_UART_MspDeInit(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_RESET; + huart->RxState = HAL_UART_STATE_RESET; + + /* Process Lock */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief UART MSP Init. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_MspInit(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_UART_MspInit could be implemented in the user file + */ +} + +/** + * @brief UART MSP DeInit. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_MspDeInit(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_UART_MspDeInit could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group2 IO operation functions + * @brief UART Transmit and Receive functions + * +@verbatim + ============================================================================== + ##### IO operation functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to manage the UART asynchronous + and Half duplex data transfers. + + (#) There are two modes of transfer: + (++) Blocking mode: The communication is performed in polling mode. + The HAL status of all data processing is returned by the same function + after finishing transfer. + (++) Non blocking mode: The communication is performed using Interrupts + or DMA, these APIs return the HAL status. + The end of the data processing will be indicated through the + dedicated UART IRQ when using Interrupt mode or the DMA IRQ when + using DMA mode. + The HAL_UART_TxCpltCallback(), HAL_UART_RxCpltCallback() user callbacks + will be executed respectively at the end of the transmit or receive process. + The HAL_UART_ErrorCallback() user callback will be executed when + a communication error is detected. + + (#) Blocking mode APIs are: + (++) HAL_UART_Transmit() + (++) HAL_UART_Receive() + + (#) Non Blocking mode APIs with Interrupt are: + (++) HAL_UART_Transmit_IT() + (++) HAL_UART_Receive_IT() + (++) HAL_UART_IRQHandler() + + (#) Non Blocking mode functions with DMA are: + (++) HAL_UART_Transmit_DMA() + (++) HAL_UART_Receive_DMA() + + (#) A set of Transfer Complete Callbacks are provided in non blocking mode: + (++) HAL_UART_TxCpltCallback() + (++) HAL_UART_RxCpltCallback() + (++) HAL_UART_ErrorCallback() + + [..] + (@) In the Half duplex communication, it is forbidden to run the transmit + and receive process in parallel, the UART state HAL_UART_STATE_BUSY_TX_RX + can't be useful. + +@endverbatim + * @{ + */ + +/** + * @brief Sends an amount of data in blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @param Timeout: Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + uint32_t tickstart = 0U; + + /* Check that a Tx process is not already ongoing */ + if(huart->gState == HAL_UART_STATE_READY) + { + if((pData == NULL ) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_BUSY_TX; + + /* Init tickstart for timeout managment */ + tickstart = HAL_GetTick(); + + huart->TxXferSize = Size; + huart->TxXferCount = Size; + while(huart->TxXferCount > 0U) + { + huart->TxXferCount--; + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + tmp = (uint16_t*) pData; + huart->Instance->DR = (*tmp & (uint16_t)0x01FFU); + if(huart->Init.Parity == UART_PARITY_NONE) + { + pData +=2; + } + else + { + pData +=1; + } + } + else + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + huart->Instance->DR = (*pData++ & (uint8_t)0xFFU); + } + } + + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* At end of Tx process, restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be received + * @param Timeout: Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + uint32_t tickstart = 0U; + + /* Check that a Rx process is not already ongoing */ + if(huart->RxState == HAL_UART_STATE_READY) + { + if((pData == NULL ) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->RxState = HAL_UART_STATE_BUSY_RX; + + /* Init tickstart for timeout managment */ + tickstart = HAL_GetTick(); + + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + /* Check the remain data to be received */ + while(huart->RxXferCount > 0U) + { + huart->RxXferCount--; + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + tmp = (uint16_t*) pData ; + if(huart->Init.Parity == UART_PARITY_NONE) + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x01FFU); + pData +=2; + } + else + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x00FFU); + pData +=1; + } + + } + else + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if(huart->Init.Parity == UART_PARITY_NONE) + { + *pData++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x00FFU); + } + else + { + *pData++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x007FU); + } + + } + } + + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + /* Check that a Tx process is not already ongoing */ + if(huart->gState == HAL_UART_STATE_READY) + { + if((pData == NULL ) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_BUSY_TX; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the UART Transmit data register empty Interrupt */ + SET_BIT(huart->Instance->CR1, USART_CR1_TXEIE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in non blocking mode + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be received + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + /* Check that a Rx process is not already ongoing */ + if(huart->RxState == HAL_UART_STATE_READY) + { + if((pData == NULL ) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->RxState = HAL_UART_STATE_BUSY_RX; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + SET_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Enable the UART Parity Error and Data Register not empty Interrupts */ + SET_BIT(huart->Instance->CR1, USART_CR1_PEIE | USART_CR1_RXNEIE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t *tmp; + + /* Check that a Tx process is not already ongoing */ + if(huart->gState == HAL_UART_STATE_READY) + { + if((pData == NULL ) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_BUSY_TX; + + /* Set the UART DMA transfer complete callback */ + huart->hdmatx->XferCpltCallback = UART_DMATransmitCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmatx->XferHalfCpltCallback = UART_DMATxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmatx->XferErrorCallback = UART_DMAError; + + /* Set the DMA abort callback */ + huart->hdmatx->XferAbortCallback = NULL; + + /* Enable the UART transmit DMA Stream */ + tmp = (uint32_t*)&pData; + HAL_DMA_Start_IT(huart->hdmatx, *(uint32_t*)tmp, (uint32_t)&huart->Instance->DR, Size); + + /* Clear the TC flag in the SR register by writing 0 to it */ + __HAL_UART_CLEAR_FLAG(huart, UART_FLAG_TC); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in non blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be received + * @note When the UART parity is enabled (PCE = 1) the data received contain the parity bit. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t *tmp; + + /* Check that a Rx process is not already ongoing */ + if(huart->RxState == HAL_UART_STATE_READY) + { + if((pData == NULL ) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->RxState = HAL_UART_STATE_BUSY_RX; + + /* Set the UART DMA transfer complete callback */ + huart->hdmarx->XferCpltCallback = UART_DMAReceiveCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmarx->XferHalfCpltCallback = UART_DMARxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmarx->XferErrorCallback = UART_DMAError; + + /* Set the DMA abort callback */ + huart->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA Stream */ + tmp = (uint32_t*)&pData; + HAL_DMA_Start_IT(huart->hdmarx, (uint32_t)&huart->Instance->DR, *(uint32_t*)tmp, Size); + + /* Enable the UART Parity Error Interrupt */ + SET_BIT(huart->Instance->CR1, USART_CR1_PEIE); + + /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + SET_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Enable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Pauses the DMA Transfer. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart) +{ + uint32_t dmarequest = 0x00U; + + /* Process Locked */ + __HAL_LOCK(huart); + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT); + if((huart->gState == HAL_UART_STATE_BUSY_TX) && dmarequest) + { + /* Disable the UART DMA Tx request */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + } + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if((huart->RxState == HAL_UART_STATE_BUSY_RX) && dmarequest) + { + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE); + CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Disable the UART DMA Rx request */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Resumes the DMA Transfer. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + if(huart->gState == HAL_UART_STATE_BUSY_TX) + { + /* Enable the UART DMA Tx request */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAT); + } + if(huart->RxState == HAL_UART_STATE_BUSY_RX) + { + /* Clear the Overrun flag before resuming the Rx transfer*/ + __HAL_UART_CLEAR_OREFLAG(huart); + + /* Reenable PE and ERR (Frame error, noise error, overrun error) interrupts */ + SET_BIT(huart->Instance->CR1, USART_CR1_PEIE); + SET_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Enable the UART DMA Rx request */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Stops the DMA Transfer. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart) +{ + uint32_t dmarequest = 0x00U; + /* The Lock is not implemented on this API to allow the user application + to call the HAL UART API under callbacks HAL_UART_TxCpltCallback() / HAL_UART_RxCpltCallback(): + when calling HAL_DMA_Abort() API the DMA TX/RX Transfer complete interrupt is generated + and the correspond call back is executed HAL_UART_TxCpltCallback() / HAL_UART_RxCpltCallback() + */ + + /* Stop UART DMA Tx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT); + if((huart->gState == HAL_UART_STATE_BUSY_TX) && dmarequest) + { + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Abort the UART DMA Tx channel */ + if(huart->hdmatx != NULL) + { + HAL_DMA_Abort(huart->hdmatx); + } + UART_EndTxTransfer(huart); + } + + /* Stop UART DMA Rx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if((huart->RxState == HAL_UART_STATE_BUSY_RX) && dmarequest) + { + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx channel */ + if(huart->hdmarx != NULL) + { + HAL_DMA_Abort(huart->hdmarx); + } + UART_EndRxTransfer(huart); + } + + return HAL_OK; +} + +/** + * @brief This function handles UART interrupt request. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +void HAL_UART_IRQHandler(UART_HandleTypeDef *huart) +{ + uint32_t isrflags = READ_REG(huart->Instance->SR); + uint32_t cr1its = READ_REG(huart->Instance->CR1); + uint32_t cr3its = READ_REG(huart->Instance->CR3); + uint32_t errorflags = 0x00U; + uint32_t dmarequest = 0x00U; + + /* If no error occurs */ + errorflags = (isrflags & (uint32_t)(USART_SR_PE | USART_SR_FE | USART_SR_ORE | USART_SR_NE)); + if(errorflags == RESET) + { + /* UART in mode Receiver -------------------------------------------------*/ + if(((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET)) + { + UART_Receive_IT(huart); + return; + } + } + + /* If some errors occur */ + if((errorflags != RESET) && (((cr3its & USART_CR3_EIE) != RESET) || ((cr1its & (USART_CR1_RXNEIE | USART_CR1_PEIE)) != RESET))) + { + /* UART parity error interrupt occurred ----------------------------------*/ + if(((isrflags & USART_SR_PE) != RESET) && ((cr1its & USART_CR1_PEIE) != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_PE; + } + + /* UART noise error interrupt occurred -----------------------------------*/ + if(((isrflags & USART_SR_NE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_NE; + } + + /* UART frame error interrupt occurred -----------------------------------*/ + if(((isrflags & USART_SR_FE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_FE; + } + + /* UART Over-Run interrupt occurred --------------------------------------*/ + if(((isrflags & USART_SR_ORE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_ORE; + } + + /* Call UART Error Call back function if need be --------------------------*/ + if(huart->ErrorCode != HAL_UART_ERROR_NONE) + { + /* UART in mode Receiver -----------------------------------------------*/ + if(((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET)) + { + UART_Receive_IT(huart); + } + + /* If Overrun error occurs, or if any error occurs in DMA mode reception, + consider error as blocking */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if(((huart->ErrorCode & HAL_UART_ERROR_ORE) != RESET) || dmarequest) + { + /* Blocking error : transfer is aborted + Set the UART state ready to be able to start again the process, + Disable Rx Interrupts, and disable Rx DMA request, if ongoing */ + UART_EndRxTransfer(huart); + + /* Disable the UART DMA Rx request if enabled */ + if(HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx channel */ + if(huart->hdmarx != NULL) + { + /* Set the UART DMA Abort callback : + will lead to call HAL_UART_ErrorCallback() at end of DMA abort procedure */ + huart->hdmarx->XferAbortCallback = UART_DMAAbortOnError; + if(HAL_DMA_Abort_IT(huart->hdmarx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + huart->hdmarx->XferAbortCallback(huart->hdmarx); + } + } + else + { + /* Call user error callback */ + HAL_UART_ErrorCallback(huart); + } + } + else + { + /* Call user error callback */ + HAL_UART_ErrorCallback(huart); + } + } + else + { + /* Non Blocking error : transfer could go on. + Error is notified to user through user error callback */ + HAL_UART_ErrorCallback(huart); + huart->ErrorCode = HAL_UART_ERROR_NONE; + } + } + return; + } /* End if some error occurs */ + + /* UART in mode Transmitter ------------------------------------------------*/ + if(((isrflags & USART_SR_TXE) != RESET) && ((cr1its & USART_CR1_TXEIE) != RESET)) + { + UART_Transmit_IT(huart); + return; + } + + /* UART in mode Transmitter end --------------------------------------------*/ + if(((isrflags & USART_SR_TC) != RESET) && ((cr1its & USART_CR1_TCIE) != RESET)) + { + UART_EndTransmit_IT(huart); + return; + } +} + +/** + * @brief Tx Transfer completed callbacks. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_UART_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Tx Half Transfer completed callbacks. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_UART_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Rx Transfer completed callbacks. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_UART_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Rx Half Transfer completed callbacks. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_UART_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief UART error callbacks. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_UART_ErrorCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group3 Peripheral Control functions + * @brief UART control functions + * +@verbatim + ============================================================================== + ##### Peripheral Control functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to control the UART: + (+) HAL_LIN_SendBreak() API can be helpful to transmit the break character. + (+) HAL_MultiProcessor_EnterMuteMode() API can be helpful to enter the UART in mute mode. + (+) HAL_MultiProcessor_ExitMuteMode() API can be helpful to exit the UART mute mode by software. + +@endverbatim + * @{ + */ + +/** + * @brief Transmits break characters. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /* Send break characters */ + SET_BIT(huart->Instance->CR1, USART_CR1_SBK); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enters the UART in mute mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /* Enable the USART mute mode by setting the RWU bit in the CR1 register */ + SET_BIT(huart->Instance->CR1, USART_CR1_RWU); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Exits the UART mute mode: wake up software. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the USART mute mode by clearing the RWU bit in the CR1 register */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_RWU); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART transmitter and disables the UART receiver. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg = 0x00; + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /*-------------------------- USART CR1 Configuration -----------------------*/ + tmpreg = huart->Instance->CR1; + + /* Clear TE and RE bits */ + tmpreg &= (uint32_t)~((uint32_t)(USART_CR1_TE | USART_CR1_RE)); + + /* Enable the USART's transmit interface by setting the TE bit in the USART CR1 register */ + tmpreg |= (uint32_t)USART_CR1_TE; + + /* Write to USART CR1 */ + WRITE_REG(huart->Instance->CR1, (uint32_t)tmpreg); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART receiver and disables the UART transmitter. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg = 0x00U; + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /*-------------------------- USART CR1 Configuration -----------------------*/ + tmpreg = huart->Instance->CR1; + + /* Clear TE and RE bits */ + tmpreg &= (uint32_t)~((uint32_t)(USART_CR1_TE | USART_CR1_RE)); + + /* Enable the USART's receive interface by setting the RE bit in the USART CR1 register */ + tmpreg |= (uint32_t)USART_CR1_RE; + + /* Write to USART CR1 */ + WRITE_REG(huart->Instance->CR1, (uint32_t)tmpreg); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group4 Peripheral State and Errors functions + * @brief UART State and Errors functions + * +@verbatim + ============================================================================== + ##### Peripheral State and Errors functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to return the State of + UART communication process, return Peripheral Errors occurred during communication + process + (+) HAL_UART_GetState() API can be helpful to check in run-time the state of the UART peripheral. + (+) HAL_UART_GetError() check in run-time errors that could be occurred during communication. + +@endverbatim + * @{ + */ + +/** + * @brief Returns the UART state. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL state + */ +HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart) +{ + uint32_t temp1= 0x00U, temp2 = 0x00U; + temp1 = huart->gState; + temp2 = huart->RxState; + + return (HAL_UART_StateTypeDef)(temp1 | temp2); +} + +/** + * @brief Return the UART error code + * @param huart : pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART. + * @retval UART Error Code + */ +uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart) +{ + return huart->ErrorCode; +} + +/** + * @} + */ + +/** + * @brief DMA UART transmit process complete callback. + * @param hdma: DMA handle + * @retval None + */ +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + /* DMA Normal mode*/ + if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U) + { + huart->TxXferCount = 0U; + + /* Disable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Enable the UART Transmit Complete Interrupt */ + SET_BIT(huart->Instance->CR1, USART_CR1_TCIE); + + } + /* DMA Circular mode */ + else + { + HAL_UART_TxCpltCallback(huart); + } +} + +/** + * @brief DMA UART transmit process half complete callback + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = (UART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_UART_TxHalfCpltCallback(huart); +} + +/** + * @brief DMA UART receive process complete callback. + * @param hdma: DMA handle + * @retval None + */ +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + /* DMA Normal mode*/ + if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U) + { + huart->RxXferCount = 0U; + + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE); + CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Disable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + } + HAL_UART_RxCpltCallback(huart); +} + +/** + * @brief DMA UART receive process half complete callback + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = (UART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_UART_RxHalfCpltCallback(huart); +} + +/** + * @brief DMA UART communication error callback. + * @param hdma: DMA handle + * @retval None + */ +static void UART_DMAError(DMA_HandleTypeDef *hdma) +{ + uint32_t dmarequest = 0x00U; + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + + /* Stop UART DMA Tx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT); + if((huart->gState == HAL_UART_STATE_BUSY_TX) && dmarequest) + { + huart->TxXferCount = 0U; + UART_EndTxTransfer(huart); + } + + /* Stop UART DMA Rx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if((huart->RxState == HAL_UART_STATE_BUSY_RX) && dmarequest) + { + huart->RxXferCount = 0U; + UART_EndRxTransfer(huart); + } + + huart->ErrorCode |= HAL_UART_ERROR_DMA; + HAL_UART_ErrorCallback(huart); +} + +/** + * @brief This function handles UART Communication Timeout. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param Flag: specifies the UART flag to check. + * @param Status: The new Flag status (SET or RESET). + * @param Timeout: Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout) +{ + /* Wait until flag is set */ + while((__HAL_UART_GET_FLAG(huart, Flag) ? SET : RESET) == Status) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0U)||((HAL_GetTick() - Tickstart ) > Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE)); + CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_TIMEOUT; + } + } + } + + return HAL_OK; +} + +/** + * @brief End ongoing Tx transfer on UART peripheral (following error detection or Transmit completion). + * @param huart: UART handle. + * @retval None + */ +static void UART_EndTxTransfer(UART_HandleTypeDef *huart) +{ + /* Disable TXEIE and TCIE interrupts */ + CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE)); + + /* At end of Tx process, restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; +} + +/** + * @brief End ongoing Rx transfer on UART peripheral (following error detection or Reception completion). + * @param huart: UART handle. + * @retval None + */ +static void UART_EndRxTransfer(UART_HandleTypeDef *huart) +{ + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); + CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; +} + +/** + * @brief DMA UART communication abort callback, when initiated by HAL services on Error + * (To be called at end of DMA Abort procedure following error occurrence). + * @param hdma DMA handle. + * @retval None + */ +static void UART_DMAAbortOnError(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + huart->RxXferCount = 0U; + huart->TxXferCount = 0U; + + HAL_UART_ErrorCallback(huart); +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart) +{ + uint16_t* tmp; + + /* Check that a Tx process is ongoing */ + if(huart->gState == HAL_UART_STATE_BUSY_TX) + { + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + tmp = (uint16_t*) huart->pTxBuffPtr; + huart->Instance->DR = (uint16_t)(*tmp & (uint16_t)0x01FFU); + if(huart->Init.Parity == UART_PARITY_NONE) + { + huart->pTxBuffPtr += 2; + } + else + { + huart->pTxBuffPtr += 1; + } + } + else + { + huart->Instance->DR = (uint8_t)(*huart->pTxBuffPtr++ & (uint8_t)0x00FFU); + } + + if(--huart->TxXferCount == 0) + { + /* Disable the UART Transmit Complete Interrupt */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_TXEIE); + + /* Enable the UART Transmit Complete Interrupt */ + SET_BIT(huart->Instance->CR1, USART_CR1_TCIE); + } + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Wraps up transmission in non blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart) +{ + /* Disable the UART Transmit Complete Interrupt */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_TCIE); + + /* Tx process is ended, restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + + HAL_UART_TxCpltCallback(huart); + + return HAL_OK; +} + +/** + * @brief Receives an amount of data in non blocking mode + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart) +{ + uint16_t* tmp; + + /* Check that a Rx process is ongoing */ + if(huart->RxState == HAL_UART_STATE_BUSY_RX) + { + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + tmp = (uint16_t*) huart->pRxBuffPtr; + if(huart->Init.Parity == UART_PARITY_NONE) + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x01FFU); + huart->pRxBuffPtr += 2U; + } + else + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x00FFU); + huart->pRxBuffPtr += 1U; + } + } + else + { + if(huart->Init.Parity == UART_PARITY_NONE) + { + *huart->pRxBuffPtr++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x00FFU); + } + else + { + *huart->pRxBuffPtr++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x007FU); + } + } + + if(--huart->RxXferCount == 0) + { + /* Disable the UART Parity Error Interrupt and RXNE interrupt*/ + CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); + + /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Rx process is completed, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + + HAL_UART_RxCpltCallback(huart); + + return HAL_OK; + } + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Configures the UART peripheral. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +static void UART_SetConfig(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg = 0x00U; + + /* Check the parameters */ + assert_param(IS_UART_BAUDRATE(huart->Init.BaudRate)); + assert_param(IS_UART_STOPBITS(huart->Init.StopBits)); + assert_param(IS_UART_PARITY(huart->Init.Parity)); + assert_param(IS_UART_MODE(huart->Init.Mode)); + + /*-------------------------- USART CR2 Configuration -----------------------*/ + tmpreg = huart->Instance->CR2; + + /* Clear STOP[13:12] bits */ + tmpreg &= (uint32_t)~((uint32_t)USART_CR2_STOP); + + /* Configure the UART Stop Bits: Set STOP[13:12] bits according to huart->Init.StopBits value */ + tmpreg |= (uint32_t)huart->Init.StopBits; + + /* Write to USART CR2 */ + WRITE_REG(huart->Instance->CR2, (uint32_t)tmpreg); + + /*-------------------------- USART CR1 Configuration -----------------------*/ + tmpreg = huart->Instance->CR1; + + /* Clear M, PCE, PS, TE and RE bits */ + tmpreg &= (uint32_t)~((uint32_t)(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | \ + USART_CR1_RE | USART_CR1_OVER8)); + + /* Configure the UART Word Length, Parity and mode: + Set the M bits according to huart->Init.WordLength value + Set PCE and PS bits according to huart->Init.Parity value + Set TE and RE bits according to huart->Init.Mode value + Set OVER8 bit according to huart->Init.OverSampling value */ + tmpreg |= (uint32_t)huart->Init.WordLength | huart->Init.Parity | huart->Init.Mode | huart->Init.OverSampling; + + /* Write to USART CR1 */ + WRITE_REG(huart->Instance->CR1, (uint32_t)tmpreg); + + /*-------------------------- USART CR3 Configuration -----------------------*/ + tmpreg = huart->Instance->CR3; + + /* Clear CTSE and RTSE bits */ + tmpreg &= (uint32_t)~((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE)); + + /* Configure the UART HFC: Set CTSE and RTSE bits according to huart->Init.HwFlowCtl value */ + tmpreg |= huart->Init.HwFlowCtl; + + /* Write to USART CR3 */ + WRITE_REG(huart->Instance->CR3, (uint32_t)tmpreg); + + /* Check the Over Sampling */ + if(huart->Init.OverSampling == UART_OVERSAMPLING_8) + { + /*-------------------------- USART BRR Configuration ---------------------*/ + if((huart->Instance == USART1) || (huart->Instance == USART6)) + { + huart->Instance->BRR = UART_BRR_SAMPLING8(HAL_RCC_GetPCLK2Freq(), huart->Init.BaudRate); + } + else + { + huart->Instance->BRR = UART_BRR_SAMPLING8(HAL_RCC_GetPCLK1Freq(), huart->Init.BaudRate); + } + } + else + { + /*-------------------------- USART BRR Configuration ---------------------*/ + if((huart->Instance == USART1) || (huart->Instance == USART6)) + { + huart->Instance->BRR = UART_BRR_SAMPLING16(HAL_RCC_GetPCLK2Freq(), huart->Init.BaudRate); + } + else + { + huart->Instance->BRR = UART_BRR_SAMPLING16(HAL_RCC_GetPCLK1Freq(), huart->Init.BaudRate); + } + } +} + +/** + * @} + */ + +#endif /* HAL_UART_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/