Mouse code for the MacroRat
Diff: mbed-dev/targets/TARGET_ARM_SSG/TARGET_MPS2/ethernet_api.c
- Revision:
- 18:6a4db94011d3
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev/targets/TARGET_ARM_SSG/TARGET_MPS2/ethernet_api.c Sun May 14 23:18:57 2017 +0000 @@ -0,0 +1,164 @@ +/* mbed Microcontroller Library + * Copyright (c) 2006-2015 ARM Limited + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +#include <string.h> + +#include "ethernet_api.h" +#include "mps2_ethernet_api.h" +#include "cmsis.h" +#include "mbed_interface.h" +#include "mbed_toolchain.h" +#include "mbed_error.h" +#include "ETH_MPS2.h" +#include "mbed_wait_api.h" + +#define TX_PKT_SIZE 256 +#define RX_PKT_SIZE 300 + +// Types +#undef FALSE +#undef TRUE +#define FALSE 0 +#define TRUE 1 + +/*---------------------------------------------------------------------------- + Ethernet Device initialize + *----------------------------------------------------------------------------*/ +int ethernet_init() +{ + int error; + error = 0; + + if(smsc9220_check_id()) { + error = TRUE; + } + + if(smsc9220_soft_reset()) { + error = TRUE; + } + + smsc9220_set_txfifo(5); + + // Sets automatic flow control thresholds, and backpressure + // threshold to defaults specified. + SMSC9220->AFC_CFG = 0x006E3740; + + if(smsc9220_wait_eeprom()) { + error = TRUE; + } + + // Configure GPIOs as LED outputs. + SMSC9220->GPIO_CFG = 0x70070000; + + smsc9220_init_irqs(); + + /* Configure MAC addresses here if needed. */ + + if(smsc9220_check_phy()) { + error = TRUE; + } + + if(smsc9220_reset_phy()) { + error = TRUE; + return error; + } + + wait_ms(100); + // Checking whether phy reset completed successfully. + { + unsigned short phyreset; + phyreset = 0; + smsc9220_phy_regread(SMSC9220_PHY_BCONTROL, &phyreset); + if(phyreset & (1 << 15)) { + error = TRUE; + return error; + } + } + + /* Advertise capabilities */ + smsc9220_advertise_cap(); + + + /* Begin to establish link */ + smsc9220_establish_link(); // bit [12] of BCONTROL seems self-clearing. + // Although it's not so in the manual. + + /* Interrupt threshold */ + SMSC9220->FIFO_INT = 0xFF000000; + + smsc9220_enable_mac_xmit(); + + smsc9220_enable_xmit(); + + SMSC9220->RX_CFG = 0; + + smsc9220_enable_mac_recv(); + + // Rx status FIFO level irq threshold + SMSC9220->FIFO_INT &= ~(0xFF); // Clear 2 bottom nibbles + + // This sleep is compulsory otherwise txmit/receive will fail. + wait_ms(2000); + return error; + +} + +/*---------------------------------------------------------------------------- + Ethernet Device Uninitialize + *----------------------------------------------------------------------------*/ +void ethernet_free() { +} + +int ethernet_write(const char *data, int size) +{ + return 0; +} + +int ethernet_send() +{ + return 0; +} + +int ethernet_receive() +{ + return 0; +} + +// Read from an recevied ethernet packet. +// After receive returnd a number bigger than 0 it is +// possible to read bytes from this packet. +// Read will write up to size bytes into data. +// It is possible to use read multible times. +// Each time read will start reading after the last read byte before. + +int ethernet_read(char *data, int dlen) +{ + return 0; +} + +void ethernet_address(char *mac) { + mbed_mac_address(mac); +} + +int ethernet_link(void) +{ + return 0; +} + +void ethernet_set_link(int speed, int duplex) +{ + smsc9220_establish_link(); +} +