File content as of revision 7:d2710f5d6f66:

#include "mbed.h"
#include <SPI.h>

#define DEBUG_SPI

#ifdef DEBUG_SPI
#define PRINTD(arg1,arg2...)    printf(arg1,##arg2)
#endif


#define SPI_MOSI    PA_7
#define SPI_MISO    PA_6
#define SPI_SCLK    PA_5
#define SPI_SSEL    PA_4

SPI spi_master(SPI_MOSI,SPI_MISO,SPI_SCLK); // MOSI, MISO, SCLK(CLK,SCK)
DigitalOut cs(SPI_SSEL);

Serial pc_serial(USBTX, USBRX);


void SPI_INIT()
{
    pc_serial.printf("Set SPI init..\n");
    pc_serial.printf("Set SPI format..\n");
    spi_master.format(8,0);
    pc_serial.printf("Set frequency to default..\n");
    //spi_master.frequency(50000000); // default 1MHz
    spi_master.frequency(1000000);
}
/*
void SPI_Write()
{
    char temp;
    int i,value;
    char response;
    char tx_cnt = -1;
    char rx_cnt = -1;
    char tx_buffer[255]={0};
    char rx_buffer[255]={0};
    PRINTD("\n==========MASTER==========\n");
    PRINTD("DATA SEND START...\n");
    PRINTD("Lock SPI BUS..\n");

    while(1)
    {
        
        temp=getchar();
        tx_buffer[++tx_cnt]=temp;
        if(temp==0x0d)
        {
            tx_buffer[tx_cnt]=0;
            PRINTD("\nData send Finish...\n");
            for(i=0;i<=tx_cnt;++i)
            {
                PRINTD("%c[%02x]",tx_buffer[i],tx_buffer[i]);
            }
            PRINTD("\n\n");
            spi_master.lock();
            for(i=0;i<=tx_cnt;++i)
            {
                value=tx_buffer[i];
                PRINTD("[M]write[%d]=%c[%02x]\n",i,value,value);
                cs=0;
                response=spi_master.write(value);
                cs=-1;
                PRINTD("[M]receive=%c[%x]\n",response,response);
                rx_buffer[++rx_cnt]=response;
            }
            spi_master.unlock();
            for(i=0;i<255;++i)
            {
                tx_buffer[i]=0;
            }
            for(i=0;i<=tx_cnt;i++)
            {
                PRINTD("init_tx_buffer[%d]=%c\n",i,tx_buffer[i]);
            }
            tx_cnt=-1;
        }
        else
        {
            PRINTD("%c[%02x]",tx_buffer[tx_cnt],tx_buffer[tx_cnt]);
        }
    }
}
*/

#define EEPROM_WREN         0x06        // Write Enable
#define EEPROM_WRDI         0x04        // Write Disable
#define EEPROM_RDSR         0x05        // Read Status Register
#define EEPROM_WRSR         0x01        // Write Status Register
#define EEPROM_READ         0x03        // Read EEPROM Memory
#define EEPROM_WRITE        0x02        // Write EEPROM Memory
#define EEPROM_MULTIREAD    0x07        // Write EEPROM Memory


enum cubeMenu { EEPROM_Write_Enable = 1 , 
                EEPROM_Write_Disable,
                EEPROM_Read_Status,
                EEPROM_Write_Status,
                EEPROM_Write_Memory,
                EEPROM_Read_Memory,
                TEST_Multi_Byte_Read,
                EXIT_Program = 9
                };

void print_menu(void)
{
    pc_serial.printf("\n\n\n\n\n\n\n"); 
     pc_serial.printf("-----------[MENU]----------\n");
     pc_serial.printf("1) Write Enable\n");//, cubeMenu.EEPROM_Write_Enable);
     pc_serial.printf("2) Write Disable\n");//, cubeMenu.EEPROM_Write_Disable);
     pc_serial.printf("3) Read Status Register\n");//, cubeMenu.EEPROM_Read_Status);
     pc_serial.printf("4) Write Status Register\n");//,cubeMenu.EEPROM_Write_Status);
     pc_serial.printf("5) Write Memory\n");//, cubeMenu.EEPROM_Write_Memory);
     pc_serial.printf("6) Read Memory\n");//, cubeMenu.EEPROM_Read_Memory);
     pc_serial.printf("7) multi byte read\n");//, cubeMenu.TEST_Multi_Byte_Read);
     pc_serial.printf("9) Exit program\n");//, cubeMenu.EXIT_Program);
     pc_serial.printf("---------------------------\n");
     pc_serial.printf("input menu : ");
}

void spi_start(void)
{
    spi_master.lock();            
    cs = 0; 
    wait_us(0);
}
void spi_end(void)
{
    wait_us(10);
    cs = 1;         
    spi_master.unlock();
}
void spi_dummy_write(void)
{
    char dummy_read;
    spi_start();
    dummy_read = spi_master.write( 0x00 );
    spi_end();
}

/*
    @convertedData : converted Data
    @sourceBuf : ASCII data array
    @lenght : sourceBuf length
    
    @return : 0 is valid hex format, other is error
*/
int converHex(char * convertedData, char * sourceBuf, int length)
{
    int ret = 0;
    char tempBuf[length];
    *convertedData = 0;
    
    
    for(int iCnt = 0 ; iCnt < length ; iCnt++)
    {
        if( ('0' <= *(sourceBuf+iCnt)) && ('9' >= *(sourceBuf+iCnt)) )
        {
            tempBuf[iCnt] = (*(sourceBuf+iCnt) - 48); 
        }
        else if( ('A' <= *(sourceBuf+iCnt)) && ('F' >= *(sourceBuf+iCnt)) )
        {
            tempBuf[iCnt] = (*(sourceBuf+iCnt) - 55); 
        }
        else if( ('a' <= *(sourceBuf+iCnt)) && ('f' >= *(sourceBuf+iCnt)) )
        {          
            tempBuf[iCnt] = (*(sourceBuf+iCnt) - 87); 
        }
        else    // error
        {
            ret = -1;
            return ret;                    
        }  
    }
    
    //pc_serial.printf("[TEST] tempBuf[0] = 0x%02X\n", tempBuf[0]);
    //pc_serial.printf("[TEST] tempBuf[1] = 0x%02X\n", tempBuf[1]);
    *convertedData = ((tempBuf[0] & 0x0F) << 4) | (tempBuf[1] & 0x0F);
    //pc_serial.printf("[TEST] convertedData = 0x%02X\n", *convertedData);
    return ret;
}

// @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ main();
int main()
{
     char dummyRead;
     char inputMenuNum = 0;
     char statusReg = 0x00;
     char test_data[10]={0};
     
     int spiTxCnt = 0;
     int spiRxCnt = 0; 
     char spiTxReadyFlag = 0;
     
     
     int res;
     
     
     int spiRxTempBuf = 0;
     char serialRxBuf[255];
     char spiRxBuf[255];
     int serialRxLen = 0;
     
     char eepAddrBuf[2] = {0};
     char eepAddr = 0;
     
     char eepDataBuf[2] = {0};
     char eepData = 0;
     int eepReadData = 0;   
     int maxInputCnt = 0;
     
     
     
     int ret;
     
     SPI_INIT();
     spi_dummy_write();
     
     
     
     
     pc_serial.printf("\n\n========== SPI Master for EEPROM [Start] ==========\n");
     
     
     while(1)
     {
         print_menu();
         inputMenuNum = pc_serial.getc();
         
         pc_serial.printf("[DEBUG] input menu number = %c\n", inputMenuNum);
         
         if( ('0' < inputMenuNum) && ('9' >= inputMenuNum) )
         {
            inputMenuNum = inputMenuNum - 48;
         }
         else
         {
             pc_serial.printf("[INFO] correct input menu number.. please retry..\n");
             wait(1);
             continue;
         }
         
                  
         
         spi_start();
         switch(inputMenuNum)
         {
             case 1:        // Write Enable =================================[OK]
                pc_serial.printf("[DEBUG] Write Enable progress..\n");
                dummyRead = spi_master.write(EEPROM_WREN);            
             break;
             
             
             
             case 2:        // Write Disable =================================[OK]             
                pc_serial.printf("[DEBUG] Write Disable progress..\n");
                dummyRead = spi_master.write(EEPROM_WRDI);                
             break;
             
             
             
             case 3:        // Read Status Register =================================[OK]
                pc_serial.printf("[DEBUG] Read Status Register progress..\n");
                spi_master.write(EEPROM_RDSR);  
                statusReg = spi_master.write(EEPROM_RDSR);     
                
                // TODO : print statusReg data to serial
                pc_serial.printf("[INFO] Status Register Data : 0x%02X\n", statusReg);
                                
             break;
             
             
             
             
             
             case 4:        // Write Status Register =================================
                pc_serial.printf("[DEBUG] Write Status Register progress..\n");
                // TODO : input data for serial
                
                    spi_master.write(EEPROM_WRSR);
                    spi_master.write(statusReg);
             break;
             
             
             
             
             
             case 5:        // Write Memory =================================
                pc_serial.printf("[DEBUG] Write Memory progress..\n");
                
                
                
                
                // EEPROM Address input
                
                maxInputCnt = 3;
                while(maxInputCnt--)
                {
                    pc_serial.printf("input Address (hex format : 00~FF) : ");
                    for(int iCnt = 0 ; iCnt < 2 ; ++iCnt)                
                    {   
                        eepAddrBuf[iCnt] = pc_serial.getc();    
                        pc_serial.printf("%c", eepAddrBuf[iCnt]); 
                    }
                    
                    ret = converHex(&eepAddr , eepAddrBuf, 2);
                    
                    if(0 == ret)
                    {
                        //pc_serial.printf("\n[DEBUG] before convert hex [0x%02x] \n", eepAddr);
                        break;
                    }
                    else        // error
                    {
                        pc_serial.printf("\n[INFO] hex formet error!\n");
                        continue;
                    }                     
                }
                
                
                if(0 == ret)
                {
                    // EEPROM data input
                    maxInputCnt = 3;
                    while(maxInputCnt--)
                    {
                        pc_serial.printf("\ninput Data (hex format : 00~FF) : ");
                        for(int iCnt = 0 ; iCnt < 2 ; ++iCnt)                
                        {   
                            eepDataBuf[iCnt] = pc_serial.getc();    
                            pc_serial.printf("%c", eepDataBuf[iCnt]); 
                        }
                        
                        int ret = converHex(&eepData , eepDataBuf, 2);
                        if(0 == ret)
                        {
                            
                            pc_serial.printf("\n[INFO] SPI Write Memory.... Start! \n");
                            //pc_serial.printf("\n[DEBUG] Addr[0x%02X] Data[0x%02X] \n", eepAddr, eepData);
                            
                            spi_master.write(EEPROM_RDSR);  
                            if(! (spi_master.write(EEPROM_RDSR) & 0x01) )
                            {                           
                                spi_master.write(EEPROM_WRITE);
                                spi_master.write(eepAddr);
                                spi_master.write(eepData);
                                pc_serial.printf("\n[INFO] SPI Write success \n");
                            }
                            else
                            {
                                pc_serial.printf("\n[INFO] SPI Write fail.. device is busy! \n");
                            }
                            
                            
                            break;
                        }
                        else        // error
                        {
                            pc_serial.printf("\n[INFO] hex formet error!\n");
                            continue;
                        }            
                    }
                }
                
                
             break;
             
             
             
             
             
             case 6:        // Read Memory =================================
                pc_serial.printf("[DEBUG] Read Memory progress..\n");
                
                // EEPROM Address input
                
                maxInputCnt = 3;
                while(maxInputCnt--)
                {
                    pc_serial.printf("input Address (hex format : 00~FF) : ");
                    for(int iCnt = 0 ; iCnt < 2 ; ++iCnt)                
                    {   
                        eepAddrBuf[iCnt] = pc_serial.getc();    
                        pc_serial.printf("%c", eepAddrBuf[iCnt]); 
                    }
                    
                    ret = converHex(&eepAddr , eepAddrBuf, 2);
                    
                    if(0 == ret)
                    {
                        //pc_serial.printf("\n[DEBUG] before convert hex [0x%02x] \n", eepAddr);
                        spi_master.write(EEPROM_READ);
                        spi_master.write(eepAddr);
                        
                        
                        eepReadData = spi_master.write(0);
                        
                        
                        pc_serial.printf("\n[DEBUG] Read EEPROM Addr[0x%02X] Data[0x%02X] \n", eepAddr, eepReadData);
                        break;
                    }
                    else        // error
                    {
                        pc_serial.printf("\n[INFO] hex formet error!\n");
                        continue;
                    }                     
                }
                
                
                
             break;
             
             
             case 7:
                pc_serial.printf("\n[DEBUG] TEST_Multi_Byte_Read\n");
                
                maxInputCnt = 3;
                while(maxInputCnt--)
                {
                    pc_serial.printf("input Address (hex format : 00~FF) : ");
                    for(int iCnt = 0 ; iCnt < 2 ; ++iCnt)                
                    {   
                        eepAddrBuf[iCnt] = pc_serial.getc();    
                        pc_serial.printf("%c", eepAddrBuf[iCnt]); 
                    }
                    
                    ret = converHex(&eepAddr , eepAddrBuf, 2);
                    
                    if(0 == ret)
                    {
                        spi_master.write(EEPROM_MULTIREAD);
                        spi_master.write(eepAddr); 
                        
                        
                        for(int i=0;i<10;i++)
                        {   
                            //test_data[i] = spi_master.write(0);
                            //spi_master.write(++eepAddr); 
                            test_data[i] = spi_master.write(0);
                            
                        }
                        
                        for(int i=0;i<10;i++)
                        {   
                            printf("\n[DEBUG] Read EEPROM Data[0x%02X]\n",test_data[i]);
                        }
                        
                        //pc_serial.printf("\n[DEBUG] Read EEPROM Addr[0x%02X]\n", eepAddr);
                        break;
                    }
                    else        // error
                    {
                        pc_serial.printf("\n[INFO] hex formet error!\n");
                        continue;
                    }                     
                }
                
                
             break;
             
             
             
             
             
             case 9:
                spi_end();
                pc_serial.printf("exit program... thank you\n");
                //return 0;   
             default:             
         }
         spi_end();
        
     }
     

     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     while(1)
     {        
        if(0 != pc_serial.readable())       // wait serial input..
        {   
            pc_serial.scanf("%s", serialRxBuf);
            serialRxLen = strlen(serialRxBuf);
            pc_serial.printf("len=[%d] %s\n", serialRxLen, serialRxBuf);
            spiTxReadyFlag = 1;
        }        
        if(1 == spiTxReadyFlag)
        {
            // SPI Send Start
            spi_master.lock();            
            cs = 0;   
            for(spiTxCnt = 0 ; spiTxCnt < serialRxLen + 1 ; ++spiTxCnt)
            {
                //printf("send Cnt[%d] [0x%02X]\n", spiTxCnt, serialRxBuf[spiTxCnt]);                         
                spi_master.write(serialRxBuf[spiTxCnt]);
                //res=spi_master.write(serialRxBuf[spiTxCnt]);
                //PRINTD("res=%c 0x[%02x]\n",res,res);
                //spiRxBuf[spiRxCnt++]=res;
            }   
            cs = 1;         
            spi_master.unlock();
            spiTxReadyFlag = 0;
        }
        
        
        
        /* TODO " ----(SPI)-----> master --> serial " */
        
        
#if 0        
        if(res!=0)
        {
            PRINTD("res=%d\n",res);
            PRINTD("res=%s\n",spiRxBuf);
        }
#endif
        
        
     }
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
#if 0   // 161005_BDK_backup2 start
    int send_data;
    SPI_INIT();   
    while(1)
    {
        SPI_Write();   
    }
#endif  // 161005_BDK_backup2 end
    return 0;
}