Diff: src/myproswift_periph.cpp

Revision:

34:029fc3b83f78

Child:

35:853be4d80ff3

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/src/myproswift_periph.cpp	Mon Sep 24 11:39:35 2018 +0000
@@ -0,0 +1,120 @@
+/*
+ ******************************************************************************
+ * file:   myswift_periph.cpp
+ *-----------------------------------------------------------------------------
+ */
+
+#include "myproswift_periph.h"
+
+/*
+ ******************************************************************************
+ * ADISense1000
+ *-----------------------------------------------------------------------------
+ */
+//connection information for initialising ADISense1000
+/*
+ADI_SENSE_CONNECTION connectionInfo = {
+    .type = ADI_SENSE_CONNECTION_TYPE_SPI,
+    .spi = {
+        .mosiPin    = SPI_MOSI,
+        .misoPin    = SPI_MISO,
+        .sckPin     = SPI_SCK,
+        .csPin      = D10,
+        .maxSpeedHz = 2000000,
+    },
+    .gpio = {
+        .resetPin     = D6,
+        .errorPin     = D3,
+        .alertPin     = D4,
+        .datareadyPin = D5,
+    },
+    .log = {
+        .txPin        = D1,
+        .rxPin        = D0,
+        .baudRate     = 115200,
+        .disableLogs  = false,
+    },
+};
+*/
+
+ADI_SENSE_CONNECTION connectionInfo = {
+    .type = ADI_SENSE_CONNECTION_TYPE_SPI,
+    .spi = {
+        .mosiPin    = 	SENSE_SPI_MOSI,
+        .misoPin    = 	SENSE_SPI_MISO,
+        .sckPin     = 	SENSE_SPI_SCK,
+        .csPin      = 	SENSE_SPI_CS,
+        .maxSpeedHz = 	SENSE_SPI_FREQUENCY,
+    },                  
+    .gpio = {           
+        .resetPin     = SENSE_RST_PIN,
+        .errorPin     = SENSE_ERROR_PIN,
+        .alertPin     = SENSE_ALERT_PIN,
+        .datareadyPin = SENSE_DREADY_PIN,
+    },
+    .log = {
+        /*
+        * #define PC_UART_TX_PIN   PA_11
+        * #define PC_UART_RX_PIN   PA_12
+        */
+        .txPin        = PA_11,
+        .rxPin        = PA_12,
+        .baudRate     = 115200,
+        .disableLogs  = false,
+    },
+};
+
+/*
+ ******************************************************************************
+ * Bluetooth Low Energy
+ *-----------------------------------------------------------------------------
+ */
+//reset pin of BLE module
+DigitalOut ble_rst(BLE_RST_PIN, 0);
+
+//flow control
+DigitalOut 	ble_Cts(BLE_CTS_PIN, 1);
+DigitalIn  	ble_Rts(BLE_RTS_PIN);
+
+//DigitalOut 	ble_Cts(BLE_CTS_PIN, 0);
+//DigitalIn  	ble_Rts(BLE_RTS_PIN, PullDown);
+
+Serial bleSerialDevice(BLE_SERIAL_TX, BLE_SERIAL_RX, BLE_BAUD_RATE);
+
+#ifdef BL652
+DigitalOut bleMode0(BLE_MODE_0_PIN, 0);
+DigitalOut bleMode1(BLE_MODE_1_PIN, 0);
+#endif
+
+
+/*
+ ******************************************************************************
+ * PC Serial
+ *-----------------------------------------------------------------------------
+ */
+
+//pointer initialised in adi_sense_Log.cpp using pins defined in this header
+Serial *gpUartDevice = new Serial(PC_UART_TX_PIN, PC_UART_RX_PIN, PC_UART_BAUDRATE);
+
+/*
+ ******************************************************************************
+ * Battery
+ *-----------------------------------------------------------------------------
+ */
+
+//pin for reading the current voltage of the battery
+//need solution to this. Battery ranges from 4.2V to 2V where the adc can only
+//read to 3.3V (VDD)
+//AnalogIn batteryV(BATTERY_V_PIN);
+
+/*
+ ******************************************************************************
+ * Status LED
+ *-----------------------------------------------------------------------------
+ */
+
+//flash when flash led is called, also iluminated when device boots successfully
+DigitalOut status_led(STATUS_LED_PIN, 0);
+//DigitalOut status_led1(PC_6, 0);
+
+