Repostiory containing DAPLink source code with Reset Pin workaround for HANI_IOT board.

Upstream: https://github.com/ARMmbed/DAPLink

Revision:
0:01f31e923fe2
diff -r 000000000000 -r 01f31e923fe2 source/family/wiznet/w7500/flash_blob.c
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/source/family/wiznet/w7500/flash_blob.c	Tue Apr 07 12:55:42 2020 +0200
@@ -0,0 +1,68 @@
+/**
+ * @file    flash_blob.c
+ * @brief   Flash algorithm for the W7500
+ *
+ * DAPLink Interface Firmware
+ * Copyright (c) 2009-2019, ARM Limited, All Rights Reserved
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "flash_blob.h"
+static const uint32_t w7500_flash_prog_blob[] = {
+    0xE00ABE00, 0x062D780D, 0x24084068, 0xD3000040, 0x1E644058, 0x1C49D1FA, 0x2A001E52, 0x4770D1F2,
+    0x4d27b430, 0x606c2400, 0x1e644d26, 0x4c26602c, 0x086d6925, 0x6125006d, 0x46a44c24, 0x4760bc30, 
+    0x47702000, 0x47702000, 0x2014b570, 0x21004c1c, 0x4d1c6061, 0x602c1e4c, 0x69224c1b, 0x006d0855, 
+    0x460b6125, 0x461a4c19, 0x200047a0, 0xb570bd70, 0x49132512, 0x604a2200, 0x17494b12, 0x4c126019, 
+    0x08496921, 0x61210049, 0x4c104601, 0x46284613, 0x200047a0, 0xb570bd70, 0x4b092422, 0x605d2500, 
+    0x175b4d08, 0x4d08602b, 0x085e692b, 0x612e0076, 0x4601460b, 0x4c054620, 0x200047a0, 0x0000bd70, 
+    0xe000ed00, 0xe000e180, 0xe000e000, 0x1fff1001, 0x00000000, 
+};
+
+/**
+* List of start and size for each size of flash sector
+* The size will apply to all sectors between the listed address and the next address
+* in the list.
+* The last pair in the list will have sectors starting at that address and ending
+* at address start + size.
+*/
+static const sector_info_t sectors_info[] = {
+    {0, 256},
+};
+
+static const program_target_t flash = {
+    0x20000041, // Init
+    0x20000045, // UnInit
+    0x20000049, // EraseChip
+    0x2000006F, // EraseSector
+    0x20000097, // ProgramPage
+    0x0,        // Verify
+    
+    // BKPT : start of blob + 1
+    // RSB  : blob start + header + rw data offset
+    // RSP  : stack pointer
+    {
+        0x20000000 + 0x00000001,
+        0x20000000 + 0x00000020 + 0x000000b0,
+        0x20000800
+    },
+
+    0x20000000 + 0x00000A00,   // mem buffer location
+    0x20000000,                // location to write prog_blob in target RAM
+    sizeof(w7500_flash_prog_blob), // prog_blob size
+    w7500_flash_prog_blob,         // address of prog_blob
+
+    // Do not modify. program_buffer_size of W7500 must be set to 0x00000100
+    0x00000100                 // ram_to_flash_bytes_to_be_written
+};