Diff: source/hic_hal/freescale/kl26z/gpio.c

Revision:

0:01f31e923fe2

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/source/hic_hal/freescale/kl26z/gpio.c	Tue Apr 07 12:55:42 2020 +0200
@@ -0,0 +1,93 @@
+/**
+ * @file    gpio.c
+ * @brief
+ *
+ * DAPLink Interface Firmware
+ * Copyright (c) 2009-2016, ARM Limited, All Rights Reserved
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "gpio.h"
+
+static void busy_wait(uint32_t cycles)
+{
+    volatile uint32_t i;
+    i = cycles;
+
+    while (i > 0) {
+        i--;
+    }
+}
+
+void gpio_init(void)
+{
+    SIM->SCGC5 |= SIM_SCGC5_PORTA_MASK | SIM_SCGC5_PORTB_MASK | SIM_SCGC5_PORTC_MASK | SIM_SCGC5_PORTD_MASK | SIM_SCGC5_PORTE_MASK;
+    // configure pin as GPIO
+    PIN_HID_LED_PORT->PCR[PIN_HID_LED_BIT] = PORT_PCR_MUX(1);
+    PIN_MSC_LED_PORT->PCR[PIN_MSC_LED_BIT] = PORT_PCR_MUX(1);
+    PIN_CDC_LED_PORT->PCR[PIN_CDC_LED_BIT] = PORT_PCR_MUX(1);
+    PIN_SW_RESET_PORT->PCR[PIN_SW_RESET_BIT] = PORT_PCR_MUX(1);
+    PIN_POWER_EN_PORT->PCR[PIN_POWER_EN_BIT] = PORT_PCR_MUX(1);
+    // led off
+    gpio_set_hid_led(GPIO_LED_OFF);
+    gpio_set_cdc_led(GPIO_LED_OFF);
+    gpio_set_msc_led(GPIO_LED_OFF);
+    // power regulator on
+    PIN_POWER_EN_GPIO->PDOR |= PIN_POWER_EN;
+    // set as output
+    PIN_HID_LED_GPIO->PDDR |= PIN_HID_LED;
+    PIN_MSC_LED_GPIO->PDDR |= PIN_MSC_LED;
+    PIN_CDC_LED_GPIO->PDDR |= PIN_CDC_LED;
+    PIN_POWER_EN_GPIO->PDDR |= PIN_POWER_EN;
+    // set as input
+    PIN_SW_RESET_GPIO->PDDR &= ~PIN_SW_RESET;
+
+    // Let the voltage rails stabilize.  This is especailly important
+    // during software resets, since the target's 3.3v rail can take
+    // 20-50ms to drain.  During this time the target could be driving
+    // the reset pin low, causing the bootloader to think the reset
+    // button is pressed.
+    // Note: With optimization set to -O2 the value 1000000 delays for ~85ms
+    busy_wait(1000000);
+}
+
+void gpio_set_hid_led(gpio_led_state_t state)
+{
+    (GPIO_LED_ON == state) ? (PIN_HID_LED_GPIO->PCOR = PIN_HID_LED) : (PIN_HID_LED_GPIO->PSOR = PIN_HID_LED);
+}
+
+void gpio_set_cdc_led(gpio_led_state_t state)
+{
+    (GPIO_LED_ON == state) ? (PIN_CDC_LED_GPIO->PCOR = PIN_CDC_LED) : (PIN_CDC_LED_GPIO->PSOR = PIN_CDC_LED);
+}
+
+void gpio_set_msc_led(gpio_led_state_t state)
+{
+    (GPIO_LED_ON == state) ? (PIN_MSC_LED_GPIO->PCOR = PIN_MSC_LED) : (PIN_MSC_LED_GPIO->PSOR = PIN_MSC_LED);
+}
+
+uint8_t gpio_get_reset_btn_no_fwrd(void)
+{
+    return 0;
+}
+
+uint8_t gpio_get_reset_btn_fwrd(void)
+{
+    return (PIN_SW_RESET_GPIO->PDIR & PIN_SW_RESET) ? 0 : 1;
+}
+
+void gpio_set_board_power(bool powerEnabled)
+{
+}