Diff: app/app_config.h

Revision:

1:edd760d6380f

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/app/app_config.h	Thu Sep 30 11:58:20 2021 +0100
@@ -0,0 +1,149 @@
+/*************************************************************************//**
+ *   @file   app_config.h
+ *   @brief  Configuration file for AD4696 device applications
+******************************************************************************
+* Copyright (c) 2021 Analog Devices, Inc.
+*
+* All rights reserved.
+*
+* This software is proprietary to Analog Devices, Inc. and its licensors.
+* By using this software you agree to the terms of the associated
+* Analog Devices Software License Agreement.
+*****************************************************************************/
+
+#ifndef APP_CONFIG_H
+#define APP_CONFIG_H
+
+/******************************************************************************/
+/***************************** Include Files **********************************/
+/******************************************************************************/
+
+#include <stdint.h>
+
+/******************************************************************************/
+/********************** Macros and Constants Definition ***********************/
+/******************************************************************************/
+
+/* List of supported platforms*/
+#define	MBED_PLATFORM		1
+
+/* Select the active platform */
+#define ACTIVE_PLATFORM		MBED_PLATFORM
+
+#if (ACTIVE_PLATFORM == MBED_PLATFORM)
+#include "app_config_mbed.h"
+
+/* Used to form a VCOM serial number */
+#define	FIRMWARE_NAME	"ad4696_mbed_iio_application"
+
+/* Redefine the init params structure mapping w.r.t. platform */
+#define bsy_gpio_extra_init_params mbed_gpio_bsy_extra_init_params
+#define ext_int_extra_init_params mbed_ext_int_extra_init_params
+#define uart_extra_init_params mbed_uart_extra_init_params
+#define spi_extra_init_params mbed_spi_extra_init_params
+#else
+#error "No/Invalid active platform selected"
+#endif
+
+// **** Note for User: ACTIVE_DEVICE selection **** //
+/* Define the device type here from the list of below device type defines
+ * (one at a time. Defining more than one device can result into compile error).
+ * e.g. #define DEV_AD4696 -> This will make AD4696 as an ACTIVE_DEVICE.
+ * The ACTIVE_DEVICE is default set to AD4696 if device type is not defined.
+ * */
+
+//#define DEV_AD4696
+
+#if defined(DEV_AD4696)
+#define ACTIVE_DEVICE		ID_AD4696
+#define ACTIVE_DEVICE_NAME	"AD4696"
+#elif defined(DEV_AD4695)
+#define ACTIVE_DEVICE		ID_AD4695
+#define ACTIVE_DEVICE_NAME	"AD4695"
+#else
+#warning No/Unsupported ADxxxxy symbol defined. AD4696 defined
+#define DEV_AD4696
+#define ACTIVE_DEVICE		ID_AD4696
+#define ACTIVE_DEVICE_NAME	"AD4696"
+#endif
+
+#if defined(DEV_AD4696)
+#define	NO_OF_CHANNELS		16
+#define ADC_RESOLUTION		16
+#elif defined(DEV_AD4695)
+#define	NO_OF_CHANNELS		16
+#define ADC_RESOLUTION		16
+#else
+/* Default config for AD4696 */
+#define	NO_OF_CHANNELS		16
+#define ADC_RESOLUTION		16
+#endif
+
+// **** Note for User: Polarity Mode selection **** //
+/* Since the pin pairing option is same for all the channels in
+ * standard sequencer mode, hence polarity mode for all the 
+ * channels is also kept same to avoid stale ADC output codes. 
+ * Make sure to change the JP6 jumper position on the Eval board to A 
+ * to use the PSEUDO_BIPOLAR_MODE. 
+ * 
+ * Select Pseudo bipolar mode (default is unipolar mode) for all the channels.
+ * e.g. #define PSEUDO_BIPOLAR_MODE -> This will enable the PSEUDO_BIPOLAR_MODE 
+ * for all the channels. 
+ * */
+ 
+//#define PSEUDO_BIPOLAR_MODE
+
+/* Pins to be used an interrupt to trigger callback function */
+#define EXT_TRIGGER_PIN 	CONVST_PIN
+
+/* ADC max count (full scale value) for unipolar inputs */
+#define ADC_MAX_COUNT_UNIPOLAR	(uint32_t)((1 << ADC_RESOLUTION) - 1)
+
+/* ADC max count (full scale value) for bipolar inputs */
+#define ADC_MAX_COUNT_BIPOLAR	(uint32_t)(1 << (ADC_RESOLUTION-1))
+
+/* Baud rate for IIO application UART interface */
+#define IIO_UART_BAUD_RATE	(230400)
+
+/****** Macros used to form a VCOM serial number ******/
+#if !defined(DEVICE_NAME)
+#define DEVICE_NAME		"DEV_AD4696"
+#endif
+
+#if !defined(PLATFORM_NAME)
+#define PLATFORM_NAME	"SDP_K1"
+#endif
+/******/
+
+/* Enable the VirtualCOM port connection/interface. By default serial communication
+ * is physical UART */
+//#define USE_VIRTUAL_COM_PORT
+
+#if defined(USE_VIRTUAL_COM_PORT)
+/* Below USB configurations (VID and PID) are owned and assigned by ADI.
+ * If intended to distribute software further, use the VID and PID owned by your
+ * organization */
+#define VIRTUAL_COM_PORT_VID	0x0456
+#define VIRTUAL_COM_PORT_PID	0xb66c
+/* Serial number string is formed as: application name + device (target) name + platform (host) name */
+#define VIRTUAL_COM_SERIAL_NUM	(FIRMWARE_NAME "_" DEVICE_NAME "_" PLATFORM_NAME)
+#endif
+
+/******************************************************************************/
+/********************** Variables and User Defined Data Types *****************/
+/******************************************************************************/
+
+/******************************************************************************/
+/************************ Public Declarations *********************************/
+/******************************************************************************/
+
+/* UART init parameters structure */
+extern struct uart_init_param uart_init_params;
+
+/* PWM descriptor */
+extern struct pwm_desc *pwm_desc;
+
+/* Initializing system peripherals */
+int32_t init_system(void);
+
+#endif //APP_CONFIG_H
\ No newline at end of file