Diff: app/app_config_mbed.h

Revision:

2:7b2b268ea49c

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/app/app_config_mbed.h	Wed Jul 20 18:12:00 2022 +0530
@@ -0,0 +1,84 @@
+/***************************************************************************//**
+ *   @file    app_config_mbed.h
+ *   @brief   Header file for Mbed platform configurations
+********************************************************************************
+ * Copyright (c) 2021-22 Analog Devices, Inc.
+ * All rights reserved.
+ *
+ * This software is proprietary to Analog Devices, Inc. and its licensors.
+ * By using this software you agree to the terms of the associated
+ * Analog Devices Software License Agreement.
+*******************************************************************************/
+
+#ifndef APP_CONFIG_MBED_H_
+#define APP_CONFIG_MBED_H_
+
+/******************************************************************************/
+/***************************** Include Files **********************************/
+/******************************************************************************/
+
+#include <stdint.h>
+#include <PinNames.h>
+
+#include "no_os_gpio.h"
+#include "mbed_uart.h"
+#include "mbed_irq.h"
+#include "mbed_gpio_irq.h"
+#include "mbed_spi.h"
+#include "mbed_gpio.h"
+
+/******************************************************************************/
+/********************** Macros and Constants Definition ***********************/
+/******************************************************************************/
+
+/* Select b/w Arduino or SDP-120 pin header (default is Arduino) */
+//#define  SDP_120
+
+#ifdef SDP_120
+/* Pin mapping of SDP-K1 w.r.t SDP-120 connector */
+#define SPI_CSB			SDP_SPI_CS_A
+#define SPI_HOST_SDO	SDP_SPI_MOSI
+#define SPI_HOST_SDI	SDP_SPI_MISO
+#define SPI_SCK			SDP_SPI_SCK
+
+#define MBED_CONV_MON	SDP_GPIO_1
+#else
+/* Pin mapping of SDP-K1 w.r.t Arduino connector */
+#define SPI_CSB			ARDUINO_UNO_D10
+#define SPI_HOST_SDO	ARDUINO_UNO_D11
+#define SPI_HOST_SDI	ARDUINO_UNO_D12
+#define SPI_SCK			ARDUINO_UNO_D13
+
+#define MBED_CONV_MON	ARDUINO_UNO_D2
+#endif
+
+#if defined(AD4130_WLCSP_PACKAGE_TYPE)
+#define	CONV_MON	MBED_CONV_MON
+#else
+#define	CONV_MON	ARDUINO_UNO_D2		// Conversion interrupt source pin (The selected interrupt source pin 
+// e.g. MCLK or GPIO needs to be tied to D2 pin on Arduino header).
+// The selection of interrupt source is done in 'iio_data_capture_init' function
+#endif
+
+/* Common pin mapping on SDP-K1 */
+#define UART_TX			CONSOLE_TX
+#define	UART_RX			CONSOLE_RX
+#define LED_GPO			LED3
+
+/* Select FS scaler value for the default user config mode.
+ * This is not a max FS value that can be set into device but rather a value to
+ * achieve max approximate ODR in the firmware for a given platform/setup.
+ * Max ODR is derived by testing the firmware on SDP-K1 controller board
+ * @10Mhz SPI clock. The max possible ODR can vary from board to board and
+ * data continuity is not guaranteed above this ODR on IIO client */
+#define FS_CONFIG_VALUE		1	// ODR = 2.4KSPS
+
+/******************************************************************************/
+/********************** Public/Extern Declarations ****************************/
+/******************************************************************************/
+
+extern struct mbed_gpio_irq_init_param mbed_ext_int_extra_init_params;
+extern struct mbed_uart_init_param mbed_uart_extra_init_params;
+extern struct mbed_spi_init_param mbed_spi_extra_init_params;
+
+#endif /* APP_CONFIG_MBED_H_ */