Diff: arch/TARGET_NXP/lpc_emac_config.h

Revision:

32:3534f0b45d38

Parent:

31:da93f0f73711

Child:

33:9de8bd8ca1c8

--- a/arch/TARGET_NXP/lpc_emac_config.h	Tue May 03 00:16:23 2016 +0100
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,111 +0,0 @@
-/**********************************************************************
-* $Id$		lpc_emac_config.h			2011-11-20
-*//**
-* @file		lpc_emac_config.h
-* @brief	PHY and EMAC configuration file
-* @version	1.0
-* @date		20 Nov. 2011
-* @author	NXP MCU SW Application Team
-* 
-* Copyright(C) 2011, NXP Semiconductor
-* All rights reserved.
-*
-***********************************************************************
-* Software that is described herein is for illustrative purposes only
-* which provides customers with programming information regarding the
-* products. This software is supplied "AS IS" without any warranties.
-* NXP Semiconductors assumes no responsibility or liability for the
-* use of the software, conveys no license or title under any patent,
-* copyright, or mask work right to the product. NXP Semiconductors
-* reserves the right to make changes in the software without
-* notification. NXP Semiconductors also make no representation or
-* warranty that such application will be suitable for the specified
-* use without further testing or modification.
-**********************************************************************/
-
-#ifndef __LPC_EMAC_CONFIG_H
-#define __LPC_EMAC_CONFIG_H
-
-#include "lwip/opt.h"
-
-#ifdef __cplusplus
-extern "C"
-{
-#endif
-
-/** @defgroup lwip_phy_config	LWIP PHY configuration
- * @ingroup lwip_phy
- *
- * Configuration options for the PHY connected to the LPC EMAC.
- * @{
- */
-
-/** \brief  The PHY address connected the to MII/RMII
- */
-#define LPC_PHYDEF_PHYADDR 1    /**< The PHY address on the PHY device. */
-
-/** \brief  Enable autonegotiation mode.
- *          If this is enabled, the PHY will attempt to auto-negotiate the
- *          best link mode if the PHY supports it. If this is not enabled,
- *          the PHY_USE_FULL_DUPLEX and PHY_USE_100MBS defines will be
- *          used to select the link mode. Note that auto-negotiation may
- *          take a few seconds to complete.
- */
-#define PHY_USE_AUTONEG 1 /**< Enables auto-negotiation mode. */
-
-/** \brief  Sets up the PHY interface to either full duplex operation or
- *          half duplex operation if PHY_USE_AUTONEG is not enabled.
- */
-#define PHY_USE_FULL_DUPLEX 1 /**< Sets duplex mode to full. */
-
-/** \brief  Sets up the PHY interface to either 100MBS operation or 10MBS
- *          operation if PHY_USE_AUTONEG is not enabled.
- */
-#define PHY_USE_100MBS 1 /**< Sets data rate to 100Mbps. */
-
-/**		  
- * @}
- */
-
-/** @defgroup lwip_emac_config	LWIP EMAC configuration
- * @ingroup lwip_emac
- *
- * Configuration options for the LPC EMAC.
- * @{
- */
-
-/** \brief  Selects RMII or MII connection type in the EMAC peripheral
- */
-#define LPC_EMAC_RMII 1         /**< Use the RMII or MII driver variant .*/
-
-/** \brief  Defines the number of descriptors used for RX. This
- *          must be a minimum value of 2.
- */
-#define LPC_NUM_BUFF_RXDESCS 3
-
-/** \brief  Defines the number of descriptors used for TX. Must
- *          be a minimum value of 2.
- */
-#define LPC_NUM_BUFF_TXDESCS (TCP_SND_QUEUELEN + 1)
-
-/** \brief  Set this define to 1 to enable bounce buffers for transmit pbufs
- *          that cannot be sent via the zero-copy method. Some chained pbufs
- *          may have a payload address that links to an area of memory that
- *          cannot be used for transmit DMA operations. If this define is
- *          set to 1, an extra check will be made with the pbufs. If a buffer
- *          is determined to be non-usable for zero-copy, a temporary bounce
- *          buffer will be created and used instead.
- */
-#define LPC_TX_PBUF_BOUNCE_EN 1
-
-/**		  
- * @}
- */
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __LPC_EMAC_CONFIG_H */
-
-/* --------------------------------- End Of File ------------------------------ */