Diff: inc/admw1001/admw1001_config.h

Revision:

77:d90214f44903

Parent:

75:434d91af4cc7

diff -r 93ad744c380d -r d90214f44903 inc/admw1001/admw1001_config.h
--- a/inc/admw1001/admw1001_config.h	Tue May 05 09:23:06 2020 +0000
+++ b/inc/admw1001/admw1001_config.h	Thu May 07 08:50:22 2020 +0000
@@ -58,8 +58,7 @@
 #define ADMW1001_SENSOR_COMMAND_MAX_LENGTH 7
 
 /*! ADMW1001 channel priority options */
-typedef enum
-{
+typedef enum {
     ADMW1001_CHANNEL_PRIORITY_0 = 0,
     ADMW1001_CHANNEL_PRIORITY_1,
     ADMW1001_CHANNEL_PRIORITY_2,
@@ -80,8 +79,7 @@
 }   ADMW1001_CHANNEL_PRIORITY;
 
 /*! ADMW1001 operating mode options */
-typedef enum
-{
+typedef enum {
     ADMW1001_OPERATING_MODE_SINGLECYCLE = 0,
     /*!< Executes a single measurement cycle and stops */
     ADMW1001_OPERATING_MODE_CONTINUOUS,
@@ -90,8 +88,7 @@
 }   ADMW1001_OPERATING_MODE;
 
 /*! ADMW1001 data ready mode options */
-typedef enum
-{
+typedef enum {
     ADMW1001_DATAREADY_PER_CONVERSION = 0,
     /*!< The DATAREADY signal is asserted after completion of each conversion
      *   - a single data sample only from the latest completed conversion is
@@ -112,8 +109,7 @@
 }   ADMW1001_DATAREADY_MODE;
 
 /*! ADMW1001 power mode options */
-typedef enum
-{
+typedef enum {
     ADMW1001_POWER_MODE_ACTIVE = 0,
     /*!< Part is fully powered up and either cycling through a sequence or awaiting a configuration */
     ADMW1001_POWER_MODE_HIBERNATION,
@@ -122,15 +118,14 @@
 }   ADMW1001_POWER_MODE;
 
 /*! ADMW1001 External Vref Buffer Mode options */
-typedef enum
-{
+typedef enum {
     ADMW1001_VREF_BUFF_MODE_DISABLE_BOTH = 0,
     /*!< Both Vref+ and Vref- buffers to be disabled */
     ADMW1001_VREF_BUFF_MODE_ONLY_POS,
     /*!< only Vref+ buffer to be disabled */
     ADMW1001_VREF_BUFF_MODE_ONLY_NEG,
     /*!< Only Vref- buffers to be disabled */
-    ADMW1001_VREF_BUFF_MODE_ENABLE_BOTH, 
+    ADMW1001_VREF_BUFF_MODE_ENABLE_BOTH,
     /*!< Both Vref+ and Vref- buffers to be Enabled */
 }   ADMW1001_VREF_BUFFER_MODE;
 
@@ -139,8 +134,7 @@
  *  Optionally select a measurement unit for final conversion results.
  *  Currently applicable only to specific temperature sensor types.
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_MEASUREMENT_UNIT_UNSPECIFIED = 0,
     /*!< No measurement unit specified */
     ADMW1001_MEASUREMENT_UNIT_CELSIUS,
@@ -150,8 +144,7 @@
 
 }   ADMW1001_MEASUREMENT_UNIT;
 
-typedef enum
-{
+typedef enum {
     ADMW1001_BUFFER_BYPASSS_DISABLED = 0,
     /*!< Buffer Bypass Disabled */
     ADMW1001_BUFFER_BYPASSS_ENABLED,
@@ -163,8 +156,7 @@
  *
  *  @note applicable only to ADC analog sensor channels
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_RTD_CURVE_EUROPEAN = 0,
     /*!< EUROPEAN RTD curve used. */
     ADMW1001_ADC_RTD_CURVE_AMERICAN,
@@ -179,8 +171,7 @@
  *
  *  @note applicable only to ADC analog sensor channels
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_GAIN_1X = 0,
     /*!< no amplification gain */
     ADMW1001_ADC_GAIN_2X,
@@ -203,8 +194,7 @@
  *  @note applicable only to ADC analog sensor channels, and
  *        specific sensor types
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_EXC_STATE_CYCLE_POWER = 0,
     /*!< Excitation for measurement is active only during measurement */
     ADMW1001_ADC_EXC_STATE_ALWAYS_ON,
@@ -217,8 +207,7 @@
  *  @note applicable only to ADC analog sensor channels, and
  *        specific sensor types
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_NO_EXTERNAL_EXC_CURRENT = -1,
     /*!< NO External excitation is provided */
     ADMW1001_ADC_EXC_CURRENT_EXTERNAL = 0,
@@ -240,8 +229,7 @@
  *
  *  @note applicable only to a diode sensor
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_100UA = 0,
     /**< 2 Current measurement 10uA 100uA        */
     ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_160UA,
@@ -266,8 +254,7 @@
  *  @note applicable only to ADC analog sensor channels, and
  *        specific sensor types
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_REFERENCE_VOLTAGE_INTERNAL = 0,
     /*!< Internal VRef - 1.2V */
     ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_1 = 1,
@@ -281,8 +268,7 @@
  *
  *  @note applicable only to ADC analog sensor channels
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_GND_SW_OPEN = 0,
     /*!< Ground switch not enabled for measurement. */
     ADMW1001_ADC_GND_SW_CLOSED,
@@ -294,8 +280,7 @@
  *
  *  @note applicable only to ADC analog sensor channels
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_DISABLE_CHOP = 0,
     /*!< chop performed. */
     ADMW1001_ENABLE_CHOP,
@@ -306,8 +291,7 @@
  *
  *  @note applicable only to ADC analog sensor channels
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_ADC_FILTER_SINC4 = 0,
     /*!< SINC4 - 4th order sinc response filter */
     ADMW1001_ADC_FILTER_SINC3,
@@ -321,29 +305,28 @@
  *  @note SF must be set in conjunction with chop mode
  *  and sinc filter type to achieve the desired sampling rate.
  */
-typedef enum
-{
-    ADMW1001_SF_122HZ  = 7,
-    /*!< SF setting for 122Hz sample rate. */
-    ADMW1001_SF_61HZ   = 31,
-    /*!< SF setting for 61Hz sample rate. */
-    ADMW1001_SF_30P5HZ = 51,
-    /*!< SF setting for 61Hz sample rate. */
-    ADMW1001_SF_10HZ   = 124,
-    /*!< SF setting for 10Hz sample rate. */
-    ADMW1001_SF_8P24HZ = 125,
-    /*!< SF setting for 8.24Hz sample rate. */
-    ADMW1001_SF_5HZ    = 127,
-    /*!< SF setting for 5Hz sample rate. */
+typedef enum {
+    ADMW1001_SF_7  = 7,
+    /*!< SF setting for fastest sampling rate, enable SINC4 filter. */
+    ADMW1001_SF_31   = 31,
+    /*!< SF setting for medium speed mode, enable SINC3 Filter. */
+    ADMW1001_SF_51 = 51,
+    /*!< SF setting for medium speed mode, enable SINC3 Filter. */
+    ADMW1001_SF_124   = 124,
+    /*!< SF setting for 60Hz rejection. */
+    ADMW1001_SF_125 = 125,
+    /*!< SF setting for 50Hz and 60Hz rejection when notch1p2 is enabled. Enable SINC3 Filter. */
+    ADMW1001_SF_127    = 127,
+    /*!< SF setting for Lowest noise, enable SINC3 Filter. */
 
 }   ADMW1001_SINC_FILTER_RANGE;
 
+
 /*! ADMW1001 I2C clock speed options
  *
  *  @note applicable only for I2C sensors
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_100K = 0,
     /*!< 100kHz I2C clock speed */
     ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_400K,
@@ -353,8 +336,7 @@
 
 
 /*! ADMW1001 Power Configuration options */
-typedef struct
-{
+typedef struct {
     ADMW1001_POWER_MODE        powerMode;
     /*!< Power mode selection */
 
@@ -365,8 +347,7 @@
  * @note required only when ADMW1001_OPERATING_MODE_MULTICYCLE is selected
  *       as the operatingMode (@ref ADMW1001_MEASUREMENT_CONFIG)
  */
-typedef struct
-{
+typedef struct {
     uint32_t    cyclesPerBurst;
     /*!< Number of cycles to complete for a single burst */
     uint32_t    burstInterval;
@@ -375,8 +356,7 @@
 }   ADMW1001_MULTICYCLE_CONFIG;
 
 /*! ADMW1001 Measurement Configuration options */
-typedef struct
-{
+typedef struct {
     ADMW1001_OPERATING_MODE    operatingMode;
     /*!< Operating mode - specifies how measurement cycles are scheduled */
     ADMW1001_DATAREADY_MODE    dataReadyMode;
@@ -411,11 +391,11 @@
     float32_t                   AVDDVoltage;
     /*!< AVDD Voltage.
      */
-     uint8_t                     extVrefBuffMode;
-     /*!< External Vref Buff mode.
+    uint8_t                     extVrefBuffMode;
+    /*!< External Vref Buff mode.
     uint32_t                    reserved1[3];
     /*!< Reserved for future use and ensure word alignment.
-     */
+    */
 
 }   ADMW1001_MEASUREMENT_CONFIG;
 
@@ -424,8 +404,7 @@
  *  @note applicable only to ADC analog sensor channels, and
  *        specific sensor types
  */
-typedef struct
-{
+typedef struct {
     ADMW1001_ADC_EXC_CURRENT              outputLevel;
     /*!< Excitation current output level */
     ADMW1001_ADC_EXC_CURRENT_DIODE_RATIO  diodeRatio;
@@ -438,8 +417,7 @@
  *
  *  @note applicable only to ADC analog sensor channels
  */
-typedef struct
-{
+typedef struct {
     ADMW1001_ADC_FILTER_TYPE    type;
     /*!< Filter type selection */
     ADMW1001_SINC_FILTER_RANGE  sf;
@@ -455,8 +433,7 @@
  *
  *  @note applicable only to ADC analog sensor channels
  */
-typedef struct
-{
+typedef struct {
     ADMW1001_ADC_SENSOR_TYPE        sensor;
     /*!< Sensor type selection */
     ADMW1001_ADC_RTD_CURVE          rtdCurve;
@@ -470,7 +447,7 @@
     ADMW1001_ADC_REFERENCE_TYPE     reference;
     /*!< ADC Reference configuration */
     uint8_t                         bufferBypass;
-     /*!< Buffer Bypass configuration */
+    /*!< Buffer Bypass configuration */
     uint8_t                         reserved0[2];
     /*!< Reserved for future use and ensure word alignment. */
     uint32_t                        reserved1[6];
@@ -481,8 +458,7 @@
 /*! ADMW1001 look-up table selection
  *  Select table used to linearise the measurement.
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_LUT_DEFAULT  = 0,
     /*!< Default LUT */
     ADMW1001_LUT_CUSTOM   = 1,
@@ -496,8 +472,7 @@
  *
  *  @note applicable only to SPI and I2C digital sensor channels
  */
-typedef enum
-{
+typedef enum {
     ADMW1001_DIGITAL_SENSOR_DATA_CODING_NONE = 0,
     /**< None/Invalid - data format is ignored if coding is set to this value */
     ADMW1001_DIGITAL_SENSOR_DATA_CODING_UNIPOLAR,
@@ -514,8 +489,7 @@
  *
  *  @note applicable only to SPI and I2C digital sensor channels
  */
-typedef struct
-{
+typedef struct {
     ADMW1001_DIGITAL_SENSOR_DATA_CODING coding;
     /**< Data Encoding of Sensor Result */
     bool littleEndian;
@@ -538,8 +512,7 @@
  *
  *  @note applicable only to digital sensor channels
  */
-typedef struct
-{
+typedef struct {
     bool                                            useCustomCommsConfig;
     /*!< Optional parameter to enable user digital communication settings */
     ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED   i2cClockSpeed;
@@ -551,8 +524,7 @@
  *
  *  @note applicable only to I2C digital sensor channels
  */
-typedef struct
-{
+typedef struct {
     ADMW1001_I2C_SENSOR_TYPE                sensor;
     /*!< Sensor type selection */
     uint8_t                                 deviceAddress;
@@ -574,8 +546,7 @@
 
 
 /*! ADMW1001 Measurement Channel configuration details */
-typedef struct
-{
+typedef struct {
     bool                                enableChannel;
     /*!< Option to include this channel in normal measurement cycles */
     bool                                disablePublishing;
@@ -652,8 +623,7 @@
      *   ID.  Lower numbers indicate higher priority, with 0 being the highest.
      *   Set to 0 if not required.
      */
-    union
-    {
+    union {
         ADMW1001_ADC_CHANNEL_CONFIG     adcChannelConfig;
         /*!< ADC channel configuration - applicable only to ADC channels */
         ADMW1001_I2C_CHANNEL_CONFIG     i2cChannelConfig;
@@ -667,8 +637,7 @@
 }   ADMW1001_CHANNEL_CONFIG;
 
 /*! ADMW1001 Diagnostics configuration details */
-typedef struct
-{
+typedef struct {
     bool                                disableGlobalDiag;
     /*!< Option to disable the following diagnostic checks on the ADC:
      *   - Reference Detection errors
@@ -692,8 +661,7 @@
 
 
 /*! ADMW1001 Device configuration details */
-typedef struct
-{
+typedef struct {
     ADMW1001_POWER_CONFIG           power;
     /*!< Power configuration details */
     ADMW1001_MEASUREMENT_CONFIG     measurement;