FRDM-KL05Z

The FRDM-KL05Z is an ultra-low-cost development platform enabled by the Kinetis L Series KL0x MCU family built on the ARM® Cortex™-M0+ processor. Features include easy access to MCU I/O, battery-ready, low-power operation, a standard-based form factor with expansion board options and a built-in debug interface for flash programming and run-control. The FRDM-KL05Z is supported by a range of NXP and third-party development software.

Overview¶

The FRDM-KL05Z has been designed by NXP in collaboration with mbed for prototyping all sorts of devices, especially those requiring the size and price point offered by Cortex-M0+. It is packaged as a development board with connectors to break out to strip board and breadboard, and includes a built-in USB FLASH programmer.

It is based on the NXP KL05Z, with a 32-bit ARM Cortex-M0+ core running at 48MHz. It includes 32KB FLASH, 4KB RAM and lots of interfaces including SPI, I2C, ADC, DAC, PWM, Touch Sensor and other I/O interfaces.

The FRDM-KL05Z is fully supported in the mbed platform, so it gets access to the free tools and SDK that provides experienced embedded developers with powerful and productive tools for building proof-of-concepts. The pinout above shows the commonly used interfaces and their locations. Note that all the numbered pins (PT_XX) can also be used as DigitalIn and DigitalOut interfaces.

Pin names¶

• mbed pin-names

Features¶

• NXP KL05Z Kinetis KL4 MCU (MKL05Z32VFM4)
  • High performance ARM® Cortex™-M0+ Core
  • 48MHz, 4KB RAM, 32KB FLASH
  • SPI (1)
  • I2C (1)
  • UART (1)
  • PWM (8)
  • ADC (6)
  • DAC (1x 12bit)
  • Touch Sensor
  • GPIO (28)

• FRDM-KL05Z Onboard Sensors
  • MMA8451Q - 3-axis accelerometer
  • Capacitive touch sensor

• Evalution Form factor
  • 81mm x 53mm
  • 5V USB or 4.5-9V supply
  • Built-in USB drag 'n' drop FLASH programmer

• mbed HDK & SDK enabled
  • Drag-n-drop programming
  • USB Serial Port
  • CMSIS-DAP
  • Online development tools
  • Easy to use C/C++ SDK
  • Lots of published libraries and projects

• Status
  • Production

Where to buy¶

Firmware¶

Getting Started with mbed¶

1. Connect your microcontroller to a PC¶

Use the USB lead to connect your mbed to a PC. The status light will come on, indicating it has power. After a few seconds of activity, the PC will recognise the mbed Microcontroller as a standard USB drive.

Windows XP example	Mac OS X example

2. Click the MBED.HTM link to get logged in¶

Go to the new USB Drive, and click MBED.HTM to open it in a web browser.

If you do not have an mbed account, choose "Signup", and create your mbed Account. Otherwise, log in with your normal username and password.

This will give you access to the website, tools, libraries and documentation.

PC Configuration¶

Your mbed Microcontroller can appear on your computer as a serial port. On Mac and Linux, this will happen by default. For Windows, you need to install a driver:

From a host PC to communicate with mbed you will need a terminal application. This allows the mbed Microcontroller to print to your PC screen, and for you to send characters back to your mbed.

• Terminals - Using Terminal applications to communicate between the Host PC and the mbed Micrcontroller

Some terminal programs (e.g. TeraTerm) list the available serial ports by name. However, if you do need to know the identity of the serial port so that you can attach a terminal or an application to it:

	'''Windows'''		'''Mac'''		'''Linux'''
	Find the identity of the COM port by opening ''Device Manager''. To do this navigate ''Start -> Control Panel -> System -> Hardware -> Device Manager''.		To find the device name under Mac OS X, use the command ''ls /dev/tty.usbmodem*''		To find the device name under Linux, use the command ''ls /dev/ttyACM*''

Downloading A program¶

1. Save a program binary (.bin) to the FRDM Platform¶

Download the appropriate "Hello World!" binary:

• NXP FRDM-KL05Z: HelloWorld_KL05Z.bin

Note: the source code for this program will be seen in the next section.

Save the program binary file to your mbed Microcontroller Disk, just like you would with a normal USB disk. The Status LED will flash as the PC writes the file to the Microcontroller disk.

2. Press the Reset Button¶

When the Reset Button in pressed, the newest program on the mbed Microcontroller Disk will be loaded in to the Microcontroller FLASH memory. The Status LED will flash as this happens.

When the program is has been loaded onto the microcontroller, it will then start it running.

3. Hello World!¶

The Microcontroller is now running the program; flashing LED1 forever! If you reset the Microcontroller, or disconnect and reconnect the power, the program will simply restart.

4. To download a different program¶

It is the newest program on the mbed Microcontroller that is run after reset. We can therefore download a new program or overwrite an existing one to update the program that will run.

Hello World!¶

Where Next¶

Follow the guide to creating your own programs using the online compiler

• Create your own program

Technical Reference¶

Power¶

• USB powered or 4.5v - 9v on Vin pin
• Current (active): < _ _ _ mA
• Current (sleep): < _ _ _ mA
• 3.3v regulated output on VOUT to power peripherals
• 5.0v from USB available on 5v (only available when USB is connected unless extra regulator is added!)
• Digital IO pins are 3.3v, 4mA each, 400mA max total

Schematics¶

• NXP FRDM-KL05Z Schematic
• NXP FRDM-KL05Z User's Manual

Data Sheets¶

• NXP KL05 Data Sheet
• NXP KL05 Reference Manual
• NXP KL05 Errata Sheet
• NXP MMA8451Q Data Sheet

Interface Firmware¶

• CMSIS-DAP Interface Firmware

 Buy Now

You need to log in to post a discussion

Discussion topics

Topic	Replies	Last post
KL05Z, low power KL05Z Sleep Power Modes and RTC	8	27 Jan 2015 by Erik -
Freescale FRDM-KL06Z	1	23 May 2014 by Martin Kojtal
compiler, microlib Project export for FRDM-KL05Z not including microlib	1	09 May 2014 by Sam Grove
FRDM-KL25Z, HCSR04 Sumo Robot on FRDM-KL05Z.	0	27 Mar 2014 by Roman Kuzmin

Questions

1 answer

Serial TX,RX yoo uta
8 years, 10 months ago

FRDM-KL05z

2 answers

FDRM-KL05Z disconnects Roland Larsson
8 years, 10 months ago

FRDM-KL05z

1 answer

KE FRDM board on mbed soon? Thor Hall
9 years, 6 months ago

FRDM-KL05z

1 answer

Timer delays and interrupts interfere with UART output Sam Ryan
9 years, 9 months ago

delay, FRDM-KL05z, interrupt, Serial, UART

2 answers

Flash overflows with GCC export by adding UART K. N. L. V.
9 years, 11 months ago

FRDM-KL05z, gcc, gcc arm embdded

See more related questions