WILLY BAYOT / stm32_adafruit

Dependents:   TDEMNucleo

Embed: (wiki syntax)

« Back to documentation index

Show/hide line numbers stm32f4xx_hal_conf.h Source File

stm32f4xx_hal_conf.h

00001 /**
00002   ******************************************************************************
00003   * @file    Demonstrations/Inc/stm32f4xx_hal_conf.h
00004   * @author  MCD Application Team
00005   * @version V1.0.0
00006   * @date    26-June-2014
00007   * @brief   HAL configuration file.
00008   ******************************************************************************
00009   * @attention
00010   *
00011   * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
00012   *
00013   * Redistribution and use in source and binary forms, with or without modification,
00014   * are permitted provided that the following conditions are met:
00015   *   1. Redistributions of source code must retain the above copyright notice,
00016   *      this list of conditions and the following disclaimer.
00017   *   2. Redistributions in binary form must reproduce the above copyright notice,
00018   *      this list of conditions and the following disclaimer in the documentation
00019   *      and/or other materials provided with the distribution.
00020   *   3. Neither the name of STMicroelectronics nor the names of its contributors
00021   *      may be used to endorse or promote products derived from this software
00022   *      without specific prior written permission.
00023   *
00024   * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
00025   * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
00026   * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
00027   * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
00028   * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
00029   * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
00030   * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
00031   * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
00032   * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
00033   * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
00034   *
00035   ******************************************************************************
00036   */ 
00037 
00038 /* Define to prevent recursive inclusion -------------------------------------*/
00039 #ifndef __STM32F4xx_HAL_CONF_H
00040 #define __STM32F4xx_HAL_CONF_H
00041 
00042 #ifdef __cplusplus
00043  extern "C" {
00044 #endif
00045 
00046 /* Exported types ------------------------------------------------------------*/
00047 /* Exported constants --------------------------------------------------------*/
00048 
00049 /* ########################## Module Selection ############################## */
00050 /**
00051   * @brief This is the list of modules to be used in the HAL driver 
00052   */
00053 #define HAL_MODULE_ENABLED         
00054 #define HAL_ADC_MODULE_ENABLED
00055 /* #define HAL_CAN_MODULE_ENABLED      */
00056 /* #define HAL_CRC_MODULE_ENABLED      */
00057 /* #define HAL_CRYP_MODULE_ENABLED     */
00058 /* #define HAL_DAC_MODULE_ENABLED      */
00059 /* #define HAL_DCMI_MODULE_ENABLED     */
00060 #define HAL_DMA_MODULE_ENABLED
00061 /* #define HAL_DMA2D_MODULE_ENABLED    */ 
00062 /* #define HAL_ETH_MODULE_ENABLED   */
00063 #define HAL_FLASH_MODULE_ENABLED 
00064 /* #define HAL_NAND_MODULE_ENABLED  */
00065 /* #define HAL_NOR_MODULE_ENABLED  */
00066 /* #define HAL_PCCARD_MODULE_ENABLED */
00067 /* #define HAL_SRAM_MODULE_ENABLED   */
00068 /* #define HAL_SDRAM_MODULE_ENABLED    */
00069 /* #define HAL_HASH_MODULE_ENABLED */
00070 #define HAL_GPIO_MODULE_ENABLED
00071 /* #define HAL_I2C_MODULE_ENABLED  */
00072 /* #define HAL_I2S_MODULE_ENABLED  */
00073 /* #define HAL_IWDG_MODULE_ENABLED */
00074 /* #define HAL_LTDC_MODULE_ENABLED */
00075 #define HAL_PWR_MODULE_ENABLED
00076 #define HAL_RCC_MODULE_ENABLED
00077 /* #define HAL_RNG_MODULE_ENABLED  */
00078 /* #define HAL_RTC_MODULE_ENABLED  */
00079 /* #define HAL_SAI_MODULE_ENABLED        */   
00080 /* #define HAL_SD_MODULE_ENABLED */
00081 #define HAL_SPI_MODULE_ENABLED
00082 /* #define HAL_TIM_MODULE_ENABLED  */
00083 /* #define HAL_UART_MODULE_ENABLED   */
00084 /* #define HAL_USART_MODULE_ENABLED  */
00085 /* #define HAL_IRDA_MODULE_ENABLED   */
00086 /* #define HAL_SMARTCARD_MODULE_ENABLED   */
00087 /* #define HAL_WWDG_MODULE_ENABLED    */
00088 #define HAL_CORTEX_MODULE_ENABLED   
00089 /* #define HAL_PCD_MODULE_ENABLED    */
00090 /* #define HAL_HCD_MODULE_ENABLED  */
00091 
00092 
00093 /* ########################## HSE/HSI Values adaptation ##################### */
00094 /**
00095   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
00096   *        This value is used by the RCC HAL module to compute the system frequency
00097   *        (when HSE is used as system clock source, directly or through the PLL).  
00098   */
00099 #if !defined  (HSE_VALUE) 
00100   #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
00101 #endif /* HSE_VALUE */
00102 
00103 #if !defined  (HSE_STARTUP_TIMEOUT)
00104   #define HSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for HSE start up, in ms */
00105 #endif /* HSE_STARTUP_TIMEOUT */
00106 
00107 /**
00108   * @brief Internal High Speed oscillator (HSI) value.
00109   *        This value is used by the RCC HAL module to compute the system frequency
00110   *        (when HSI is used as system clock source, directly or through the PLL). 
00111   */
00112 #if !defined  (HSI_VALUE)
00113   #define HSI_VALUE    ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
00114 #endif /* HSI_VALUE */
00115 
00116 /**
00117   * @brief Internal Low Speed oscillator (LSI) value.
00118   */
00119 #if !defined  (LSI_VALUE) 
00120  #define LSI_VALUE  ((uint32_t)40000)    
00121 #endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
00122                                              The real value may vary depending on the variations
00123                                              in voltage and temperature.  */
00124 /**
00125   * @brief External Low Speed oscillator (LSE) value.
00126   */
00127 #if !defined  (LSE_VALUE)
00128  #define LSE_VALUE  ((uint32_t)32768)    /*!< Value of the External Low Speed oscillator in Hz */
00129 #endif /* LSE_VALUE */
00130 
00131 /**
00132   * @brief External clock source for I2S peripheral
00133   *        This value is used by the I2S HAL module to compute the I2S clock source 
00134   *        frequency, this source is inserted directly through I2S_CKIN pad. 
00135   */
00136 #if !defined  (EXTERNAL_CLOCK_VALUE)
00137   #define EXTERNAL_CLOCK_VALUE    ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/
00138 #endif /* EXTERNAL_CLOCK_VALUE */
00139 
00140 /* Tip: To avoid modifying this file each time you need to use different HSE,
00141    ===  you can define the HSE value in your toolchain compiler preprocessor. */
00142 
00143 /* ########################### System Configuration ######################### */
00144 /**
00145   * @brief This is the HAL system configuration section
00146   */     
00147 #define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */
00148 #define  TICK_INT_PRIORITY            ((uint32_t)0x0F) /*!< tick interrupt priority */           
00149 #define  USE_RTOS                     0     
00150 #define  PREFETCH_ENABLE              1              
00151 #define  INSTRUCTION_CACHE_ENABLE     1
00152 #define  DATA_CACHE_ENABLE            1
00153 
00154 /* ########################## Assert Selection ############################## */
00155 /**
00156   * @brief Uncomment the line below to expanse the "assert_param" macro in the 
00157   *        HAL drivers code
00158   */
00159 /* #define USE_FULL_ASSERT    1 */
00160 
00161 /* ################## Ethernet peripheral configuration ##################### */
00162 
00163 /* Section 1 : Ethernet peripheral configuration */
00164 
00165 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
00166 #define MAC_ADDR0   2
00167 #define MAC_ADDR1   0
00168 #define MAC_ADDR2   0
00169 #define MAC_ADDR3   0
00170 #define MAC_ADDR4   0
00171 #define MAC_ADDR5   0
00172 
00173 /* Definition of the Ethernet driver buffers size and count */   
00174 #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
00175 #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
00176 #define ETH_RXBUFNB                    ((uint32_t)4)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
00177 #define ETH_TXBUFNB                    ((uint32_t)4)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
00178 
00179 /* Section 2: PHY configuration section */
00180 
00181 /* DP83848 PHY Address*/ 
00182 #define DP83848_PHY_ADDRESS             0x01
00183 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 
00184 #define PHY_RESET_DELAY                 ((uint32_t)0x000000FF)
00185 /* PHY Configuration delay */
00186 #define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFF)
00187 
00188 #define PHY_READ_TO                     ((uint32_t)0x0000FFFF)
00189 #define PHY_WRITE_TO                    ((uint32_t)0x0000FFFF)
00190 
00191 /* Section 3: Common PHY Registers */
00192 
00193 #define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */
00194 #define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */
00195  
00196 #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
00197 #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
00198 #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
00199 #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
00200 #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
00201 #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
00202 #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
00203 #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
00204 #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
00205 #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
00206 
00207 #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
00208 #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
00209 #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
00210   
00211 /* Section 4: Extended PHY Registers */
00212 
00213 #define PHY_SR                          ((uint16_t)0x10)    /*!< PHY status register Offset                      */
00214 #define PHY_MICR                        ((uint16_t)0x11)    /*!< MII Interrupt Control Register                  */
00215 #define PHY_MISR                        ((uint16_t)0x12)    /*!< MII Interrupt Status and Misc. Control Register */
00216  
00217 #define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
00218 #define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
00219 #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
00220 
00221 #define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
00222 #define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
00223 
00224 #define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
00225 #define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
00226 
00227 /* Includes ------------------------------------------------------------------*/
00228 /**
00229   * @brief Include module's header file 
00230   */
00231 
00232 #ifdef HAL_RCC_MODULE_ENABLED
00233   #include "stm32f4xx_hal_rcc.h"
00234 #endif /* HAL_RCC_MODULE_ENABLED */
00235 
00236 #ifdef HAL_GPIO_MODULE_ENABLED
00237   #include "stm32f4xx_hal_gpio.h"
00238 #endif /* HAL_GPIO_MODULE_ENABLED */
00239 
00240 #ifdef HAL_DMA_MODULE_ENABLED
00241   #include "stm32f4xx_hal_dma.h"
00242 #endif /* HAL_DMA_MODULE_ENABLED */
00243    
00244 #ifdef HAL_CORTEX_MODULE_ENABLED
00245   #include "stm32f4xx_hal_cortex.h"
00246 #endif /* HAL_CORTEX_MODULE_ENABLED */
00247 
00248 #ifdef HAL_ADC_MODULE_ENABLED
00249   #include "stm32f4xx_hal_adc.h"
00250 #endif /* HAL_ADC_MODULE_ENABLED */
00251 
00252 #ifdef HAL_CAN_MODULE_ENABLED
00253   #include "stm32f4xx_hal_can.h"
00254 #endif /* HAL_CAN_MODULE_ENABLED */
00255 
00256 #ifdef HAL_CRC_MODULE_ENABLED
00257   #include "stm32f4xx_hal_crc.h"
00258 #endif /* HAL_CRC_MODULE_ENABLED */
00259 
00260 #ifdef HAL_CRYP_MODULE_ENABLED
00261   #include "stm32f4xx_hal_cryp.h" 
00262 #endif /* HAL_CRYP_MODULE_ENABLED */
00263 
00264 #ifdef HAL_DMA2D_MODULE_ENABLED
00265   #include "stm32f4xx_hal_dma2d.h"
00266 #endif /* HAL_DMA2D_MODULE_ENABLED */
00267 
00268 #ifdef HAL_DAC_MODULE_ENABLED
00269   #include "stm32f4xx_hal_dac.h"
00270 #endif /* HAL_DAC_MODULE_ENABLED */
00271 
00272 #ifdef HAL_DCMI_MODULE_ENABLED
00273   #include "stm32f4xx_hal_dcmi.h"
00274 #endif /* HAL_DCMI_MODULE_ENABLED */
00275 
00276 #ifdef HAL_ETH_MODULE_ENABLED
00277   #include "stm32f4xx_hal_eth.h"
00278 #endif /* HAL_ETH_MODULE_ENABLED */
00279 
00280 #ifdef HAL_FLASH_MODULE_ENABLED
00281   #include "stm32f4xx_hal_flash.h"
00282 #endif /* HAL_FLASH_MODULE_ENABLED */
00283  
00284 #ifdef HAL_SRAM_MODULE_ENABLED
00285   #include "stm32f4xx_hal_sram.h"
00286 #endif /* HAL_SRAM_MODULE_ENABLED */
00287 
00288 #ifdef HAL_NOR_MODULE_ENABLED
00289   #include "stm32f4xx_hal_nor.h"
00290 #endif /* HAL_NOR_MODULE_ENABLED */
00291 
00292 #ifdef HAL_NAND_MODULE_ENABLED
00293   #include "stm32f4xx_hal_nand.h"
00294 #endif /* HAL_NAND_MODULE_ENABLED */
00295 
00296 #ifdef HAL_PCCARD_MODULE_ENABLED
00297   #include "stm32f4xx_hal_pccard.h"
00298 #endif /* HAL_PCCARD_MODULE_ENABLED */ 
00299   
00300 #ifdef HAL_SDRAM_MODULE_ENABLED
00301   #include "stm32f4xx_hal_sdram.h"
00302 #endif /* HAL_SDRAM_MODULE_ENABLED */      
00303 
00304 #ifdef HAL_HASH_MODULE_ENABLED
00305  #include "stm32f4xx_hal_hash.h"
00306 #endif /* HAL_HASH_MODULE_ENABLED */
00307 
00308 #ifdef HAL_I2C_MODULE_ENABLED
00309  #include "stm32f4xx_hal_i2c.h"
00310 #endif /* HAL_I2C_MODULE_ENABLED */
00311 
00312 #ifdef HAL_I2S_MODULE_ENABLED
00313  #include "stm32f4xx_hal_i2s.h"
00314 #endif /* HAL_I2S_MODULE_ENABLED */
00315 
00316 #ifdef HAL_IWDG_MODULE_ENABLED
00317  #include "stm32f4xx_hal_iwdg.h"
00318 #endif /* HAL_IWDG_MODULE_ENABLED */
00319 
00320 #ifdef HAL_LTDC_MODULE_ENABLED
00321  #include "stm32f4xx_hal_ltdc.h"
00322 #endif /* HAL_LTDC_MODULE_ENABLED */
00323 
00324 #ifdef HAL_PWR_MODULE_ENABLED
00325  #include "stm32f4xx_hal_pwr.h"
00326 #endif /* HAL_PWR_MODULE_ENABLED */
00327 
00328 #ifdef HAL_RNG_MODULE_ENABLED
00329  #include "stm32f4xx_hal_rng.h"
00330 #endif /* HAL_RNG_MODULE_ENABLED */
00331 
00332 #ifdef HAL_RTC_MODULE_ENABLED
00333  #include "stm32f4xx_hal_rtc.h"
00334 #endif /* HAL_RTC_MODULE_ENABLED */
00335 
00336 #ifdef HAL_SAI_MODULE_ENABLED
00337  #include "stm32f4xx_hal_sai.h"
00338 #endif /* HAL_SAI_MODULE_ENABLED */
00339 
00340 #ifdef HAL_SD_MODULE_ENABLED
00341  #include "stm32f4xx_hal_sd.h"
00342 #endif /* HAL_SD_MODULE_ENABLED */
00343 
00344 #ifdef HAL_SPI_MODULE_ENABLED
00345  #include "stm32f4xx_hal_spi.h"
00346 #endif /* HAL_SPI_MODULE_ENABLED */
00347 
00348 #ifdef HAL_TIM_MODULE_ENABLED
00349  #include "stm32f4xx_hal_tim.h"
00350 #endif /* HAL_TIM_MODULE_ENABLED */
00351 
00352 #ifdef HAL_UART_MODULE_ENABLED
00353  #include "stm32f4xx_hal_uart.h"
00354 #endif /* HAL_UART_MODULE_ENABLED */
00355 
00356 #ifdef HAL_USART_MODULE_ENABLED
00357  #include "stm32f4xx_hal_usart.h"
00358 #endif /* HAL_USART_MODULE_ENABLED */
00359 
00360 #ifdef HAL_IRDA_MODULE_ENABLED
00361  #include "stm32f4xx_hal_irda.h"
00362 #endif /* HAL_IRDA_MODULE_ENABLED */
00363 
00364 #ifdef HAL_SMARTCARD_MODULE_ENABLED
00365  #include "stm32f4xx_hal_smartcard.h"
00366 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
00367 
00368 #ifdef HAL_WWDG_MODULE_ENABLED
00369  #include "stm32f4xx_hal_wwdg.h"
00370 #endif /* HAL_WWDG_MODULE_ENABLED */
00371 
00372 #ifdef HAL_PCD_MODULE_ENABLED
00373  #include "stm32f4xx_hal_pcd.h"
00374 #endif /* HAL_PCD_MODULE_ENABLED */
00375 
00376 #ifdef HAL_HCD_MODULE_ENABLED
00377  #include "stm32f4xx_hal_hcd.h"
00378 #endif /* HAL_HCD_MODULE_ENABLED */
00379    
00380 /* Exported macro ------------------------------------------------------------*/
00381 #ifdef  USE_FULL_ASSERT
00382 /**
00383   * @brief  The assert_param macro is used for function's parameters check.
00384   * @param  expr: If expr is false, it calls assert_failed function
00385   *         which reports the name of the source file and the source
00386   *         line number of the call that failed. 
00387   *         If expr is true, it returns no value.
00388   * @retval None
00389   */
00390   #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
00391 /* Exported functions ------------------------------------------------------- */
00392   void assert_failed(uint8_t* file, uint32_t line);
00393 #else
00394   #define assert_param(expr) ((void)0)
00395 #endif /* USE_FULL_ASSERT */
00396 
00397 
00398 #ifdef __cplusplus
00399 }
00400 #endif
00401 
00402 #endif /* __STM32F4xx_HAL_CONF_H */
00403 
00404 
00405 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/